General Lab Products, Bellco Glass
-
Impeller Assembly 50-500mL
Bellco GlassGlass shaft impeller assembly for 1967-style hanging bar spinner flask. Consist of ptfe magnet holder and ptfe coated magnet. Glass shaft ptfe magnet Size: 50-500ml
-
Vessel Flange Gasket 10 For Bioreactor Vessels
Bellco GlassVessel flange gasket 10l for bioreactor vessels
-
Thermowell Assembly 3L
Bellco GlassThermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube. Thermowell assemblies for 1965 and 1967-style angled sidearm…
-
Impeller Assembly 25mL
Bellco GlassGlass shaft impeller assembly for 1967-style hanging bar spinner flask. Consist of ptfe magnet holder and ptfe coated magnet. Glass shaft ptfe magnet Size: 25ml
-
The bellco sample system attaches to the headplate of a bioreactor allowing the user to take repeated aseptic samples into a standard 50ml disposable conical tube. The sampler is designed to connect to an existing pipe by mounting under the nut of a headplate stud. Samples are taken by evacuating…
-
Stainless Steel 3-Port Assembly 500mL 70mm
Bellco GlassSize: 500ml Seam welded w/ electropolish finish 3-port w/ siphon, fill & vent tubes Includes: 45mm pp cap & silicone gasket Dimensions: 1/4? x 5/32? Longest tube: 2 5/8? at bend Neck: 70mm
-
Heating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Heating blanket - benchmark Flask size: 3l Watts: 295 Heating @ 5 watts per sq in Male iec connector for use with temperature controller Dimensions: 2"…
-
Compression Reducer Fitting 1/2 - 1/4"
Bellco GlassThese fittings are designed specifically for the bellco control systems and fit through a 5/16" fitting on the stainless steel headplate. Stainless steel Size: 1/2" – ¼"
-
Micro-carrier Impeller Assembly 500mL
Bellco GlassImpeller assembly for micro-carrier spinner flasks. Consist of magnet holder, silicone plug, magnet, and ptfe paddle. Impeller size: 500ml Paddle dimensions: 1" x 3"
-
3-Port Thermowell Assembly 15L
Bellco GlassThermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube. Port Thermowell assembly For low profile 3l vessel Material: 316l…
-
Bellco Heating Blanket 115V-36L Low Watt 375 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 36l Watts: 375 - low wattage Dimension (in.): 5 x 48 3…
-
IOB Impeller Assembly 500mL 70mm
Bellco GlassStainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks Cap size: 70mm Flask size: 500ml Paddle: 2" x 2"
-
-
Material: 316l SST with electropolish finish - outside only Dimensions: 1/2" od x .430"id x 18" l
-
Stainless Steel 2-Port Assembly 6L
Bellco GlassAll port assemblies are manufactured from 316l stainless steel and have an electropolish finish. 2- port assemblies have siphon and vent tubes. 3-port assemblies have siphon, fill tube and vent tubes. All port assemblies include a 45mm blue polypropylene screw cap and white silicone gasket. Size:…
-
3-Port Sparger Assembly w/ Holes 36L
Bellco Glass316-l stainless steel ra32 or better finish .040? drilled holes sparger for low profile vertical side arm vessels. Threaded end is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket. Triple tube configuration with vent, fill/sample and sparge.
-
Stainless Steel Condenser For 3L Bioreactor
Bellco GlassStainless steel condenser for 3l bioreactor
-
Round Bottom Marine Impeller 15L
Bellco GlassDimensions: 1/2? od x 12 1/2? long Stainless steel 4? od right hand pitch marine prop & e-clip Material: 316l stainless steel with electropolish finish For round bottom omni vessel (1964-88405) Need l/f head plate, over head drive motor
-
Bellco Heating Blanket 230V-8L 375 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 8l Watts: 375 Dimension (in.): 3 x 26.5 2 latches 6ft…
-
Silicone Headplate O-Ring 10L #274
Bellco GlassSilicone headplate o-ring for 10l bioreactor systems. Material: red silicone rubber Dimensions: od x id: 5.762?x 0.139? thick Size: #274
-
Natural Micro-Tube 1.5mL Bulk Packed - Snap Top
Bellco GlassSize: 1.5ml Material: homo-polymer polypropylene Color: natural Bulk packed
-
Large Flange Z/Z Paddle 36L
Bellco GlassManufactured from 316l stainless steel with electropolish finish. Ra 32 finish or better inside and out. Ideal use for cell culture and reduces shear in delicate cell culture. Blade dimension: 5 3/4 x 2? Shaft oal: 14 1/2? Constructed of 316l electropolished stainless steel Marine impeller includes…
-
Flexgrip Chuck For 10mm Pestle Glass & Stirrer Rods
Bellco GlassIdeal use for pestle glass and stirrer rods. Used with homogenizer drive. Size: 10mm
-
Stainless Steel Probe Capseal 1L w/ PTFE IOB 4 Ports
Bellco GlassThe stainless steel 100mm iob probe cap seal is manufactured from 316l stainless steel and has a red-silicone sealing gasket with a 100mm blue polypropylene screw cap. The stainless steel probe cap seal has four accessory ports surrounding a centrally located internal impeller assembly. Two of…
-
Manufactured from 316l stainless steel with ra32 finish or better inside and out. The assemblies attach to the headplate.
-
Sparger w/ Holes 3L
Bellco Glass316 l stainless steel sparger assembly with drilled holes for 3-liter bioreactor vessel. .250x.152 Welded flange,"3/8" Silicone 'o' ring
-
-
316l stainless steel bent harvesting tube for 15l flat bottom omni vessel. Use with large flange head-plate. Size: 1/2" x 20" Id: .430"
-
3-Port Harvest Assembly 8L
Bellco GlassMaterial: 316l SST with electropolish finish, ra 32 or better, inside & out Dimensions: harvest tube (3/8" od) - 1" above slug, 15" insertion length Addition tube (1/4"od) - 1" above slug, 2 21/64" below Vent tube (1/4" od) - 1" above slug, .975" below Supply with 45mm pp blue open top screw cap &…
-
Thermowell Assembly 1L
Bellco GlassThermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube Thermowell assemblies for 1965 and 1967-style angled sidearm…
-
Large Flange O-Ring Only 200mm
Bellco Glass200 mm large flange 0-ring for use with SST flange clamp. 200 mm 0-ring Red silicone rubber construction
-
Micro-Carrier Impeller Assembly 100-250mL
Bellco GlassImpeller assembly for micro-carrier spinner flasks. Consist of magnet holder, silicone plug, magnet, and ptfe paddle. Impeller size: 100-250ml Paddle dimensions: 1" x 2"