General Lab Products
-
Bellco Heating Blanket 230V-3L 150 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 3l Watts: 150 Dimension (in.): 2 x 17.5 1 latch 6ft cord…
-
Stainless Steel Shaft Assembly 15-36L
Bellco GlassManufactured from 316l stainless steel. Impeller assembly for micro-carrier spinner flasks. 1965 series micro-carrier spinner flask Size: 15-36l
-
Glass Micro-Carrier Impeller Shaft 15-36L
Bellco GlassManufactured from type 1 class a Borosilicate glass. For spinner flasks 3l to 36l Dimensions: 9mm x 500mm long
-
Digital IOB Insect System 3L 115v
Bellco GlassDesigned for growing insect cell cultures such as sf9 and sf21 cells. The system comes complete with all accessories needed to grow your insect culture line for expression. Consist of: 7785-d2005 digital 5-position magnetic stirrer, 115v 1965-13000 micro-carrier spinner flask, 3l 1965-60030 iob…
-
Bellco Heating Blanket 230V-500mL 50 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 500ml Watts: 50 Dimension (in.): 1 x 10.5 1 latch 6ft…
-
Micro-Carrier Screw Cap Assembly 70mm 100-500mL
Bellco GlassPolypropylene screw cap with silicone gasket pouring ring and compression fitting.
-
Heat / Cool Coil 15L
Bellco GlassHeating and cooling coils are used for cell culture temperature manipulation within the bioreactor vessel. Must be hooked up to a water circulating mechanism for heating or cooling. Fits through ports on a stainless steel head plate. 316l electropolished stainless steel For cell culture temperature…
-
-
Compression Fitting 12mm
Bellco GlassBellco compression fittings are designed using our standard 45mm blue polypropylene open top caps and white silicone gaskets. A wide variety of fittings are available to allow ph and do monitoring via insertion of these probes into sidearms or vessels. Bellco probe adapters are designed to allow…
-
Process Micro-Carrier Insect System 3L 115v
Bellco GlassDesigned for growing insect cell cultures such as sf9 and sf21 cells. The system comes complete with all accessories needed to grow your insect culture line for expression. Consist of: 7785-p2005 process 5-position magnetic stirrer, 115v 1965-03000 micro-carrier spinner flask complete, 3l…
-
Flexgrip Chuck For 10mm Pestle Glass & Stirrer Rods
Bellco GlassIdeal use for pestle glass and stirrer rods. Used with homogenizer drive. Size: 10mm
-
PE, 1 to 1 1/2 gpm. Flexible discharge tube and hose hook with tapered adapter fit 1 to 5 gal containers or cans. Internal flapper valve prevents reverse flow.Uses: mild solvents, light oils, corrosives, dilute acid/caustics, liquid waxes, and disinfectants. Barrel: 21 in. L. Hose: 38 L x 1 in. diameter.
-
Stainless steel curved harvesting tube for 5l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 5l Dimensions: 1/4" x 5/32 x 14 1/4"
-
Stainless steel curved harvesting tube for 36l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 36l Dimensions: 1/4" x 5/32 x 24"
-
Thermowell Assembly 15L
Bellco GlassThermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube. Thermowell assemblies for 1965 and 1967-style angled sidearm…
-
Stainless Steal Bioreactor Headplate 7L
Bellco GlassManufactured from 316l stainless steel with ra 32 finish or better inside and out. Fittings are sold separately as part of the system.
-
Micro-Carrier Impeller Assembly 1-3L
Bellco GlassImpeller assembly for micro-carrier spinner flasks. Consist of magnet holder, silicone plug, magnet, and ptfe paddle. Impeller size: 1-3l Paddle dimensions: 1 3/4" x 4 1/4" Consist of: Magnet holder: a523-207 Silicone plug: a523-200 Magnet: 1975-0300a Ptfe paddle: a523-206
-
Low Profile 3-Port Sparger w/ Frit 6L
Bellco Glass316-l stainless steel ra32 or better finish 10 micron porosity stainless steel frit for low profile vertical side arm vessels. Frit is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket Triple tube configuration with vent, fill/sample and sparge.
-
2-port air stone stainless steel sparger assembly is designed for the sparging of gases into the vessel liquid media. This design allows access through the side arms with a screw on cap assembly. Fully autoclavable. Sparger assembly for 6l l/p over head drive vessel Fits thru a 45mm sidearm 316l…
-
Straight Harvesting Tube 7.5L 1/4"
Bellco GlassMaterial: 316l SST with ra finish of 32 micro inch or better- inside & out Dimensions: 1/4" od x 5/32"id x 7.5" long
-
Aldrich® Pump N' Pour can adapter NPTM 2 in.
MilliporeSigmaManufactured of PBT Polybutylene Terephthalate, an extremely tough and chemically resistant plastic material. Use adapter to pour directly from can or to adapt hand pump. See. AL-222 for instructions on installation. Legal Information: Aldrich is a registered trademark of Sigma-Aldrich Co. LLC
-
Thermowell assembly is manufactured from 316l stainless steel with 32ra finish or better. It can be used with rtd temperature sensor. Includes polypropylene screw cap and silicone gasket. There are also tubes for addition media and vent. Thermowell assemblies attach to the sidearms with a screw cap…
-
Removable baffle for large flange vessels. Material: SST 36l with electropolish finish Dimensions: 1 1/2" wide x 10 1/2" long Fits on any 1/4" od SST tube inside vessel Recommend: 2 per vessel Z-shaped
-
3-Port Sparger Assembly w/ Frit 8L
Bellco Glass316-l stainless steel ra32 or better finish 10 micron porosity stainless steel frit for low profile vertical side arm vessels. Frit is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket Triple tube configuration with vent, fill/sample and sparge.
-
3-Port Sparger Assembly w/ Frit 36L
Bellco Glass316-l stainless steel ra32 or better finish 10 micron porosity stainless steel frit for low profile vertical side arm vessels. Frit is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket Triple tube configuration with vent, fill/sample and sparge.
-
Metal Stone Sparger 15L For Flat Bottom Omni Vessels
Bellco GlassMetal stone sparger 15l for flat or round bottom omni vessels. Sparger inserts through stainless steel headplate fitting. 4 1/2?wide x 20 1/2? long 316 l stainless steel ra 32 finish or better Stainless steel frit
-
Stainless Steel Bent Harvesting Tube 15L 1/4"x20"
Bellco Glass316l stainless steel bent harvesting tube for 15l flat bottom omni vessel. Use with large flange head-plate. Size: 1/4" x 20" Id: 5/32"
-
Valley Heating Blanket 115V-6L 300 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 6l Watts: 300 Dimension (in.): 3 x 22 2 latches 6ft cord…
-
Four-digit hand-held tally counter chrome-plated
MilliporeSigmaEquipped with recording lever, reset knob, and finger ring.
-
Metal Stone Sparger 5L For Round Bottom Omni Vessels
Bellco GlassMetal stone sparger 5l for flat or round bottom omni vessels. Sparger inserts through stainless steel headplate fitting. 4 1/2?wide x 14? long 316 l stainless steel ra 32 finish or better Stainless steel frit
-
Thermowell Assembly 36L
Bellco GlassThermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube. Thermowell assemblies for 1965 and 1967-style angled sidearm…
-
Stainless Steel Bent Harvesting Tube 5L 1/4"x16"
Bellco Glass316l stainless steel bent harvesting tube for 5l flat bottom omni vessel. Use with large flange head-plate. Size: 1/4" x 16" Id: 5/32"