Sparging accessory for vertical sidearm spinner flasks. Manufactured from 316l stainless steel with electropolish finish. Includes polypropylene cap with 1/4? white compression fitting and white silicone gasket. .040 inch hole for aeration of fermentation cultures where shear force is less critical.

Stainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks. Cap size: 100mm Flask size: 15l Paddle: 9 1/2" x 6"

Large flange air stone sparger for large flange vessels. Fits through stainless steel head plate fitting. These spargers fit through a 5/16? fitting. 316 l stainless steel Ra 32 finish or better Acrodisc filter assembly, 0.2 micron

316 l stainless steel construction

Manufactured from type 1 class a Borosilicate glass. For spinner flasks 3l to 36l Dimensions: 9mm x 500mm long

Material: 316l SST with electropolish finish, ra 32 or better, inside & out Dimensions: harvest tube (3/8" od) - 1" above slug, 15" insertion length Addition tube (1/4"od) - 1" above slug, 2 21/64" below Vent tube (1/4" od) - 1" above slug, .975" below Supply with 45mm pp blue open top screw cap &…

Impeller assembly for micro-carrier spinner flasks. Consist of magnet holder, silicone plug, magnet, and ptfe paddle. Impeller size: 1-3l Paddle dimensions: 1 3/4" x 4 1/4" Consist of: Magnet holder: a523-207 Silicone plug: a523-200 Magnet: 1975-0300a Ptfe paddle: a523-206

Size: 1l Seam welded w/ electropolish finish 3-port w/ siphon, fill & vent tubes Includes: 45mm pp cap & silicone gasket

Heating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 500ml Watts: 50 Dimension (in.): 1 x 10.5 1 latch 6ft…

316l stainless steel bent harvesting tube for 15l flat bottom omni vessel. Use with large flange head-plate. Size: 1/4" x 20" Id: 5/32"

Thermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube. Port Thermowell assembly For low profile 3l vessel Material: 316l…

Stainless steel curved harvesting tube for 8l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 8l Dimensions: 1/2" x .430 x 20"

Stainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks. Cap size: 100mm Flask size: 6l Paddle: 6 3/4" x 5" Overall length: 10 1/2"

Metal stone sparger 15l round bottom Metal stone sparger 15l for flat or round bottom omni vessels. Sparger inserts through stainless steel headplate fitting. 4 1/2?wide x 23 1/2? long 316 l stainless steel ra 32 finish or better Stainless steel frit

Heating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 8l Watts: 375 Dimension (in.): 3 x 26.5 2 latches 6ft…

Sparger for vertical sidearm spinner flasks. Includes polypropylene cap with 1/4? compression fitting and white silicone gasket. Material: 316l stainless steel with electropolish finish Ra 32 finish or better Includes polypropylene cap, 1/4" white compression fitting, white silicone gasket…

Metal stone sparger 15l for flat or round bottom omni vessels. Sparger inserts through stainless steel headplate fitting. 4 1/2?wide x 20 1/2? long 316 l stainless steel ra 32 finish or better Stainless steel frit

Media addition bottle 1l

Stainless steel curved harvesting tube for 5l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 5l Dimensions: 1/2 x .430 x 14 1/4"

Dimensions: 1/2? od x 12 1/2? long Stainless steel 4? od right hand pitch marine prop & e-clip Material: 316l stainless steel with electropolish finish For round bottom omni vessel (1964-88405) Need l/f head plate, over head drive motor

Includes 2 clear silicone tubes molded into the stopper with 6" on both sides of the slug Tubing is 3/16" id x 3/8" od.

Over head drive adjustable paddle 8-36l

316-l stainless steel ra32 or better finish .040? drilled holes sparger for low profile vertical side arm vessels. Threaded end is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket. Triple tube configuration with vent, fill/sample and sparge.

2-port air stone stainless steel sparger assembly is designed for the sparging of gases into the vessel liquid media. This design allows access through the side arms with a screw on cap assembly. Fully autoclavable. Sparger assembly for 6l l/p over head drive vessel Fits thru a 45mm sidearm 316l…

Metal stone sparger 5l for flat or round bottom omni vessels. Sparger inserts through stainless steel headplate fitting. 4 1/2?wide x 12? long 316 l stainless steel ra 32 finish or better Stainless steel frit

Micro-carrier screw cap assembly

Stainless steel curved harvesting tube for 36l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 36l Dimensions: 1/4" x 5/32 x 24"

Size: 36l Seam welded w/ electropolish finish 3-port w/ siphon, fill & vent tubes Includes: 45mm pp cap & silicone gasket Dimensions: 1/4" x 5/32" Longest tube: 12 1/8" at bend

316-l stainless steel ra32 or better finish 10 micron porosity stainless steel frit for low profile vertical side arm vessels. Frit is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket Triple tube configuration with vent, fill/sample and sparge.

Stainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks. Cap size: 100mm Flask size: 500ml Paddle: 2" x 2"

Sparger for vertical sidearm spinner flasks. Includes polypropylene cap with 1/4? compression fitting and white silicone gasket. Material: 316l stainless steel with electropolish finish Ra 32 finish or better Size: 21?

Heating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Watts: 150 Dimension (in.): 2"tall x 17.5 diameter 1 latch Caution:…