General Lab Products, Bellco Glass, Supplies
-
Bellco Heating Blanket 230V-15L 750 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 1200 - not to be use with CellTrol Watts: 1200 Dimension…
-
Round Bottom Marine Impeller 8L
Bellco GlassDimensions: 1/2? od x 12 1/2? long Stainless steel 4? od right hand pitch marine prop & e-clip Material: 316l stainless steel with electropolish finish For round bottom omni vessel (1964-88405) Need l/f head plate, over head drive motor Size: 8l
-
Stainless Steel Shaft Assembly 100mL
Bellco GlassManufactured from 316l stainless steel. Impeller assembly for micro-carrier spinner flasks. 1965 series micro-carrier spinner flask Size: 100ml
-
Low Profile 3-Port Thermowell Assembly 6L
Bellco GlassThermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube. Port Thermowell assembly For low profile 3l vessel Material: 316l…
-
IOB Impeller Assembly 500mL
Bellco GlassStainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks. Cap size: 100mm Flask size: 500ml Paddle: 2" x 2"
-
IOB Impeller Assembly 8L
Bellco GlassStainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks. Cap size: 100mm Flask size: 8l Paddle: 6 3/4" x 5"
-
Size: 1.5ml Material: homo-polymer polypropylene Color: natural Individually wrapped
-
Impeller Assembly 15-36L
Bellco GlassGlass shaft impeller assembly for 1967-style hanging bar spinner flask. Consist of ptfe magnet holder and ptfe coated magnet. Glass shaft ptfe magnet Size: 15-36l
-
GL45 L-Bubble Tube w/ Holes 36L w/ (10) .040 Holes
Bellco GlassSparger for vertical sidearm spinner flasks. Includes polypropylene cap with 1/4? compression fitting and white silicone gasket. Material: 316l stainless steel with electropolish finish Ra 32 finish or better Includes polypropylene cap, 1/4" white compression fitting, white silicone gasket…
-
Large Flange Round Bottom Vessel 7L
Bellco GlassHeavy walled construction for cell culture and fermentation applications. Heavy duty o-ring flange creates positive seal for stainless steel head-plate. For use with stainless steel head-plate, o-ring, and locking clamp. Use with CellTrol ii only single or dual systems, and speed control modules.…
-
Large Flange Flat Bottom Omni Vessel 8L
Bellco GlassHeavy walled construction for cell culture and fermentation applications. Heavy duty o-ring flange creates positive seal for stainless steel head-plate. For use with stainless steel head-plate, o-ring, and locking clamp. Can be used with series 500 controllers or with CellTrol ii (no speed) and…
-
Stainless steel curved harvesting tube for 5l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 5l Dimensions: 1/4" x 5/32 x 14 1/4"
-
Flat Bottom Large Flange Omni Vessel 5L
Bellco GlassBlades and impeller assemblies are use for cell culture. Reduces shear in delicate cell culture. Manufactured from 316l stainless steel with electropolish finish. Ra 32 finish or better inside and out. Blade dimension: 5 3/4 x 2?. Shaft oal: 6 3/4?. Constructed of 316l electropolished stainless…
-
Valley Heating Blanket 115V-500mL 50 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Watts: 50 Dimension (in.): 1 1/2" tall x 10.5 diameter 1 latch 6f…
-
Extended Heat / Cool Coil 36L
Bellco GlassHeating and cooling coils are used for cell culture temperature manipulation within the bioreactor vessel. Must be hooked up to a water circulating mechanism for heating or cooling. 316l electropolished stainless steel For cell culture temperature manipulation Od x oal: 3 1/4 x 22" #turns: 5 1/2…
-
Thermowell assembly is manufactured from 316l stainless steel with 32ra finish or better. It can be used with rtd temperature sensor. Includes polypropylene screw cap and silicone gasket. There are also tubes for addition media and vent. Thermowell assemblies attach to the sidearms with a screw cap…
-
Glass Ball Impeller Only 100mL
Bellco GlassGlass ball houses a magnet for gentle agitation of micro-carrier beads and has a 70mm cap. Specially formed bottom indent prevents accumulation under the impeller Cap size: 70mm Size: 100ml
-
Stainless steel curved harvesting tube for 36l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 36l Dimensions: 1/2" x .430 x 24"
-
Thermowell assembly is manufactured from 316l stainless steel with 32ra finish or better. It can be used with rtd temperature sensor. Includes polypropylene screw cap and silicone gasket. There are also tubes for addition media and vent. Thermowell assemblies attach to the sidearms with a screw cap…
-
Bellco Heating Blanket 230V-36L-HW 1200 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 1200 - not to be use with CellTrol Watts: 1200 Dimension…
-
Large Flange Flat Bottom Omni Vessel 15L
Bellco GlassHeavy walled construction for cell culture and fermentation applications. Heavy duty o-ring flange creates positive seal for stainless steel head-plate. For use with stainless steel head-plate, o-ring, and locking clamp. Can be used with series 500 controllers or with CellTrol ii (no speed) and…
-
-
Metal stone sparger 15l round bottom Metal stone sparger 15l for flat or round bottom omni vessels. Sparger inserts through stainless steel headplate fitting. 4 1/2?wide x 23 1/2? long 316 l stainless steel ra 32 finish or better Stainless steel frit
-
Valley Heating Blanket 115V-3L 150 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Watts: 150 Dimension (in.): 2"tall x 17.5 diameter 1 latch Caution:…
-
Round Bottom Marine Impeller 15L
Bellco GlassBlade dimensions: 5 3/4" x 2" Shaft: 14 1/2" Stainless steel 4? od right hand pitch marine prop & e-clip Material: 316l stainless steel with electropolish finish For round bottom omni vessel (1964-88405) Need l/f head plate, over head drive motor
-
Stainless Steel 3-Port Assembly 1L
Bellco GlassSize: 1l Seam welded w/ electropolish finish 3-port w/ siphon, fill & vent tubes Includes: 45mm pp cap & silicone gasket
-
-
-
Thermowell Assembly 15L
Bellco GlassThermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube. Thermowell assemblies for 1965 and 1967-style angled sidearm…
-
Stainless Steel Shaft Assembly 1L
Bellco GlassManufactured from 316l stainless steel. Impeller assembly for micro-carrier spinner flasks. 1965 series micro-carrier spinner flask Size: 1l
-
Glass Ball Impeller Only 3L
Bellco GlassGlass ball houses a magnet for gentle agitation of micro-carrier beads and has a 70mm cap. Specially formed bottom indent prevents accumulation under the impeller. Cap size: 100mm Size: 3l
-
Stainless Steel Bent Harvesting Tube 8L 1/4" x 18"
Bellco Glass316l stainless steel bent harvesting tube for 8l flat bottom omni vessel. Use with large flange head-plate. Size: 1/4" x 18" Id: 5/32"