Extraction Lab Equipment

This Filtration Kit allows rapid separation of mixtures via vacuum filtration. The stopper is cut to hold a Buchner funnel. The hand-operated vacuum pump simplifies vacuum filtration, eliminating the need for a water source or vacuum aspirator. It is more economical than an electric vacuum pump. The...

Modular PYREX Accelerated One-Step extractor-concentrator performs extraction, concentration, and drying with the same apparatus and is designed for use with solvents of heavier specific gravity than sample being extracted.  Extraction and concentration can be done in 1/3 of the time....

Soxlet Extractor Upper Joint: Available in 34/45, 45/50, and 55/50 Lower Joint: Available 24/40 Used for the extraction of solids with a solvent.

These clips are meant to secure the connection of two ground glass joints. PRODUCT WARNINGS WARNING: This product can expose you to chemicals including styrene, which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information go to...

Two-piece grease-free sublimer with a flat bottom to enable heating on a hot plate stirrer. Condenser has a large top opening for use with dry ice / acetone or liquid nitrogen. Connection between the flask and condenser is made with a flat o-ring joint permitting parts to be gently separated for...

High purity, seamless thimble filters offered in 5 materials. Applications include analysis of fats, oils, grease, pesticides, pollutants, organics and addititives in plastics and rubbers. Cellulose Fiber is made from alpha cotton cellulose. These thimbles are binder-free and suitable for Soxlet...

Each Vessel comes with: ASME U Stamped, National Board of Boiler and Pressure Vessel Inspectors (NB) Registration Vacuum and Recovery Pumps sold Separately Delivery and Installation not Included Onsite Instruction not Included All Stainless Steel Parts and Accessories ASME JACKET CANNON 15 ...

Micro scale sublimer can be used with quantities as small as 0.5 grams. The sublimer has a capacity of 3mL between the lower portion of the cold finger and the interior bottom of the flask. With 24/25 standard taper joints to connect the flask and cold finger condenser.

Optimum solution for the acid/basic hydrolysis of food and feed samples prior to solvent extraction for total fat analysis. Improves Analysis Hydrolysis / digestion by acid or base Ensures conformity with AOAC standard No sample transfer – no sample loss Crucibles go directly into SER 148...

Flat-bottom flask for Soxhlet Extraction Apparatus 1/Case

A liquid-liquid extractor for use with lighter or heavier-than-water extracting solvents. Overflow and boil-up tube uses Ace-Thred Connections, thus allowing easy removal for cleaning to reduce cross contamination among samples. Complete consists of:Extractor Body, (approx.1.3L capacity), Dispersion...

High purity, seamless thimble filters offered in 5 materials. Applications include analysis of fats, oils, grease, pesticides, pollutants, organics and addititives in plastics and rubbers. Silica Fiber (Quartz) thimbles are made of pure quartz microfibers and are binder-free. Ideal for air sampling...

This 1L PYREX® single piece continuous liquid/liquid extractor is for use with solvents of heavier specific gravity than sample liquid being extracted. It is designed to meet EPA test method requirements outlined by SW-846, RCRA, and CLP. The sidearm is sealed to the extractor body just below the...

High purity, seamless thimble filters offered in 5 materials. Applications include analysis of fats, oils, grease, pesticides, pollutants, organics and addititives in plastics and rubbers. Glass Fiber thimbles are made of pure borosilicate glass microfibers. These binder-free filters can withstand...

With an ACE fritted disc sealed in. Can be used in any standard Soxhlet extraction apparatus. The sizes below correspond to the size specifications of extraction bodies and will fit those units. Available in porosities A, B, C, D and E. All porosities of a given size are priced the same. Height...

This 1L PYREX® extractor body has a 45/50 Standard Taper outer top joint, a middle 35/25 Spherical Joint ball joint and a bottom 18/9 Spherical Joint socket joint. It is a component of the modular Continuous Heavier than Water Liquid/Liquid Extractor (Nos. 3922-M and 3924-M) and...

Includes an efficient Friedrichs condenser An efficient extraction apparatus for general purpose use Consists of an extractor, a special Friedrichs condenser and a flask, all equipped with Standard Taper joints Condenser tubulation o.d. is 10 mm for 3/8 inch i.d. tubing

A grease-free, two-piece sublimation apparatus consisting of an upper water cooled condenser and lower vessel to hold the material to be sublimed. The sublimate collects on the lower end of the condenser which has a flat bottom. Condenser is constructed using a grease-free, threaded valve....

Use this apparatus for continuous extraction of analytes from a solid into an organic solvent. As the flask containing the solvent is heated, vapors rise in the larger outside tube, enter the water-cooled condenser, and liquate. When the liquid level in the extractor reaches the top of the bent...

Goldfisch Fat Extractor Accessories and Replacement Parts include glassware, gaskets and other components.

Extraction Thimble, All Glass Available in multiple sizes (small, medium, large) Porosity: Available in Extra Course and Course All glass extraction thimble permits viewing extraction process and subsequent weighing.

Designed for U.S.E.P.A. Priority Pollutant analysis using Method 625 (base neutrals/acid extractables). Accommodates 1L sample and approximately 200mL of a heavier-than-water extracting solvent. Features an extractor body designed to accept a common condenser with a 45/50 joint, a 24/40 opening with...

Soxhlet extactor body with standard taper outer joint at top and 24/40 standard taper inner joint at bottom.

Similar in design to CG-1360 but with the addition of a 2mm PTFE stopcock in the return tube. Stopcock stops the flow after the extraction is complete. For samples of 1 liter plus approximately 200mL of extracting solvent. Extractor has a 45/50 top outer joint and a 24/40 inner joint on the uptake...