Select up to 3 products
Condenser has a specially formed spiral inner tube providing a long vapor path, ensuring good heat transfer and anti-flooding characteristics. Condenser has a standard taper outer joint at a 15° angle to the condenser and a lower inner drip tip joint. Hose connections have an O.D. of 10mm at the...
Allihn Reflux Condenser with a water cooled inner drip tip at the bottom for Soxhlet Extractors. Joint Size: Available in 34/45, 45/50, and 55/50 Jacket Length: Available in 190, 260, and 300mm.
Liebig Condenser, Removable Hose Connections Jacket Length: 120, 180, 200, 250, 300, 400, and 500mm Joints: 14/20, 19/22, and 24/40 available Hose Connection OD: 8mm With outer joint at the top and inner joint at the bottom.
These PYREX® condensers have a high surface area per unit length of the 200mm long jacket with a 19/38 Standard Taper outer joint at the top and a plain drip tip at the bottom. They are primarily used in distillation assemblies Condenser tubulations are approximately 10mm O.D.
High efficiency air condenser is a waterless glass condenser that requires no cooling water for operation. The glass bellows design provides a high surface area air condenser which is very effective. Performance of the high efficiency air condenser is equivalent to a Liebig type condenser being used...
Condenser for use in refluxing from 1 to 20mL of solvent in flasks having a capacity of 5 to 50mL. Minimal surface area provides for better yields while providing adequate cooling. The additional hose connection is provided to allow introduction of an inert gas such as nitrogen. Top hose connection...
Indentations at the bottom for supporting packing material. Jacket permits the column to be used as a condenser.
Jacket has an O.D. of 40mm while coil O.D. is 8mm to provide maximum cooling capacity.
Graham Coiled condensing tube is sealed into water jacket Inlet and outlet tubes on opposite sides of jacket With Standard Taper drip tip joint at bottom and Standard Taper outer joint at top The 8” condenser has 19/38 joints; others have Standard Taper 24/40 joints
With Standard Taper 24/40 joints Inlet and outlet tubes, 10 mm o.d. are on opposite sides, indentations at lower end of condenser tube support packing when used as fractionating column.
Vacuum adapters have 24/40 joints. Bent adapter has a 105° angle between the top outer joint and bottom inner joint. Straight adapter has a top outer joint and bottom inner joint. Both adapters have 24/40 joints and include a 3/8" hose connector.
Allihn Condenser Jacket Length: 120, 200, 300 or 400mm available Joints: 14/20, 19/22 or 29/42 available Hose Connection OD: 8 or 10mm With outer joint at the top and inner joint at the bottom.
Useful for refluxing and distillation assemblies. The narrow annular space of the West design provides high cooling efficiency due to the increased flow rate of the cooling medium Medium length Standard Taper joints Condensate is not restricted with this design Manufactured from 33 expansion, low...
Liebig Condenser Jacket Length: 100, 120, 180, 200, 250, 300, 400, and 500mm Joints: 14/20, 19/22 and 24/40 available Hose Connection: 8 or 10mm With outer joint at the top and inner joint at the bottom.
Replacement condenser for Buchi rotary evaporators. Available plain or safety coated. Includes PTFE hose barbs,GL caps and plug.
Our Liebig Condensers are made from high-quality borosilicate glass and have a straight sealed inner tube and two inlet/outlet arms. These condensers have rubber connections. PRODUCT WARNINGS WARNING: This product can expose you to chemicals including benzene, which are known to the State of...
Friedrich Condenser with hose connection sidearm. 45/50 bottom standard taper joint Ring-sealed inner condensing tube with inner drip joint and side outlet for drying tube Molded 190 mm inner cold finger Used primarily in reflux mode and Soxhlet extractions Fits tubing ID 3/8"
Narrow annular space between jacket and inner tube of the West condenser provides for excellent cooling efficiency due to the increased flow rate of water. Condenser has a top standard taper outer joint and a lower inner drip tip joint. Hose connections have an O.D. of 10mm at the middle serration.
For use in construction of spiral or Graham style CONDENSERSs. Coils can be sealed together to form longer lengths.