Hemco

Hemco

Products (12)

Compare Tool

Select up to 3 products

  • Stainless Steel Wall Canopy Hoods

    Canopy hoods are designed to collect and exhaust corrosive vapors, heat, steam, and odors when mounted over areas with water baths, hot plates, or portable equipment. Made of type 304 Stainless Steel, the Canopy Fume Hood’s glass smooth surfaces provide superior chemical, corrosion and heat...

  • Epoxy Resin Work Surfaces

    Epoxy Resin Worksurfaces are recommended for general laboratory work where greater chemical resistance is required. Surface is dished 3/8" to contain spillage. Worksurface is cast of thermosetting epoxy resin, creating a molded solid 1-1/4" thick top which is extremely hard, abrasion and...

  • Fiberglass Island Canopy Hoods

    Canopy hoods are designed to collect and exhaust corrosive vapors, heat, steam, and odors when mounted over areas with water baths, hot plates, or portable equipment. Made of composite resin, the Canopy Fume Hood’s glass smooth surfaces provide superior chemical, corrosion and heat resistance....

  • UniFlow LE AireStream Laboratory Fume Hoods

    UniFlow LE Airestream fume hoods are a high-efficiency, full duty, low flow constant volume for energy savings & maximum user protection. The aerodynamic face opening with airfoil provides uniform air flow through the fume chamber. The Vector baffle system directs the air through the fume...

  • MicroFlow II Filtered Workstation

    The MicroFlow II Workstation is ideal for: A Class 1 ductless hood workstation. Activated Carbon Filtration for fumes, odors, and non-hazardous chemical vapors, pre-filter for particulate Completely self contained with clear hood surround with safety viewing sash for user Clear hood surround with...

  • Fiberglass Wall Canopy Hoods

    Canopy hoods are designed to collect and exhaust corrosive vapors, heat, steam, and odors when mounted over areas with water baths, hot plates, or portable equipment. Made of composite resin, the Canopy Fume Hood’s glass smooth surfaces provide superior chemical, corrosion and heat resistance....

  • MicroFlow I Ductless Workstation

    The MicroFlow I Workstation is ideal for: A Class 1 ductless hood workstation. Activated Carbon Filtration for fumes, odors, and non-hazardous chemical vapors, pre-filter for particulate. Completely self contained with clear hood surround with safety viewing sash for user Integral work surface...

  • Universal Fume Hoods

    The Universal Fume Hood is designed for light to medium duty fume removal, and offers such features as a sturdy dual wall construction, and a fully vertical sliding sash. It is completely molded of fire retardant fiberglass. Thomas Numbers 1167M01-M04: Units do not have a blower and require a...

  • Phenolic Work Surfaces

    Flat phenolic work surface for Universal and Clean Aire II hoods.

  • Fume Hood Exhaust Blowers

    Epoxy coated steel, belt drive, exhaust blowers for canopy hoods based on duct runs under 25ft and no more than 4 elbows. These exhaust blowers are designed to maintain between 80 to 100FPM.

  • UniLine Fume Hood Base Cabinets

    Base cabinets built to last! UniLine Fume Hood Base Cabinets are constructed of top grade furniture steel and finished in a chemical resistant powder coated finish meeting or exceeding SEFA 8 recommended practice for laboratory casework. UniLine Base Cabinets set the standard for safety and...

  • Clean Aire II Ductless Fume Hoods

    Clean Aire II Fume Hoods are a Class 1 ductless hood workstation with activated Carbon Filtration for fumes, odors, non-hazardous chemical vapors. This is a self contained ductless hood unit, equipped with integral carbon filter, vapor proof light, vertical sash and controls, and completely molded...

Compare Tool

Select up to 3 products