Glass

Compare Tool

Select up to 3 products

1 - 32 of 68
Sort
View
Show
  • Synthware Rotary Evaporator Anti-Splash Traps, Modified

    Kemtech America

    Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With two 4mm drain holes at the base of the inner tube to allow solvent to drain back into the evaporation flask. Has upper outer and lower inner standard taper joints.

  • Synthware Vacuum Adapters with Glass Stopcocks, 90°

    Kemtech America

    Synthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper inner joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

  • Synthware Distillation Adapters

    Kemtech America

    Adapter is bent 105 degrees. The top outer and lower inner standard taper joints are the same size.

  • Synthware Vacuum Adapters with Outer Joints & Glass Stopcocks

    Kemtech America

    Synthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper outer joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

  • Synthware Distilling Adapters, 105°

    Kemtech America

    Synthware distillation adapter with sealed in drip tip. Adapter is bent at 105 degrees. Standard taper top outer joint and lower inner joints. 

  • Synthware Distillation Adapters, 75°

    Kemtech America

    Synthware distillation adapter bent at 75 degrees. Both ends are standard taper inner joints and are the same size.

  • Synthware Vacuum/Inert Gas Adapters

    Kemtech America

    Allows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. Hose connection is at a 90 degree angle to the standard taper inner joint.

  • Synthware Rotary Evaporator Anti-Splash Traps with Fritted Discs, Modified

    Kemtech America

    Synthware rotary evporator anti-splash trap, modified. With extra coarse porosity fritted disc sealed above lower inner joint. Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. Frit reduces foam overflow from being…

  • Synthware Enlarging Adapters

    Kemtech America

    Synthware enlarging adapters are used for connecting dissimilar standard taper joint sizes. The lower inner joint is smaller in size than the top outer joint.

  • Synthware Long Stem Inlet Adapters

    Kemtech America

    Synthware long stem inlet adapter. With standard taper top outer joint and lower inner joint with sealed in lower tube extending below the inner joint.

  • Synthware Inlet/Thermometer Adapters

    Kemtech America

    Adapter has a Nylon compression cap and a Viton o-ring to form a vacumm tight seal. Cap accommodates 5.0 - 7.5mm O.D. thermometer or gas inlet tube. To use it as a syringe port, simply replace the o-ring with a PTFE-lined septum. Supplied with one Nylon cap and one Viton o-ring.

  • Synthware Rotary Evaporator Anti-Splash Traps

    Kemtech America

    Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With upper outer and lower inner standard taper joints.

  • Synthware Vacuum/Inert Gas Adapters with Ball Joint

    Kemtech America

    Allows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. Hose connection is at a 90 degree angle to the spherical ball joint.

  • Synthware Vacuum Adapters with Glass Stopcocks, Straight

    Kemtech America

    Synthware vacuum adapter with a serrated hose connection 180 degrees to the standard taper inner joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

  • Kjeldahl Trap Adapters

    Kemtech America

    Synthware distillation adapter with Kjeldahl trap. With two standard taper inner joints that are parallel and at a 75 degree angle to the connecting tube. Distance between joints is approximately 200mm.

  • Synthware Vacuum Distilling Adapters

    Kemtech America

    With two standard taper inner joints that are parallel and at a 75 degree angle to the connecting tube. Distance between joints is 100mm.

  • Synthware Inlet Adapters

    Kemtech America

    For use with gas inlet tubes or plain stem thermometers. Supplied with one holed rubber adapter.

  • Synthware Kjeldahl Distilling Trap Adapters

    Kemtech America

    Adapter is placed above flask to prevent carry-over of reactions which have a tendency to foam. With top outer and lower inner standard taper joints.

  • Synthware Drying Tubes, 75°

    Kemtech America

    Synthware drying tube angled at 75 degrees. Angled to avoid dessicant contact with reactions. With standard taper inner joint.

  • Synthware Thermometer Adapters

    Kemtech America

    Synthware thermometer adapter with a 5 degree offset and a serrated hose connection for vacuum. Joints are standard taper.

  • Synthware Distillation Adapters, Vigreux

    Kemtech America

    Synthware Vigreux distillation connecting adapter. Indenstations in lower section improve liquid/vapor contact. The standard taper top outer joint accomodates a 76mm immersion thermometer. Bottom and side joints are standard taper inner joints.

  • Synthware Rotary Evaporator Vapor Ducts

    Kemtech America

    Synthware rotary evaporator vapor duct. Precision ground and polished. Meet manufacturer's standards. With standard taper inner joint.

  • U-Shaped Adapters

    Kemtech America

    Synthware U-shaped adapter. With standard taper inner joints at both ends.

  • Synthware Straight Drying Tubes

    Kemtech America

    Synthware straight drying tube. With top outer and lower inner standard taper joints of the same size.

  • Synthware Vacuum Filtration Adapters

    Kemtech America

    Used with plain stem Buchner funnels and pluro-stopper. Hose connector has an O.D. of 10mm at the largest serration. Joint is a standard taper inner joint. Pluro-stoppers are not included.

  • Synthware Vacuum/Inert Gas Adapters, 90°

    Kemtech America

    Allows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. Hose connection is at a 90 degree angle to the standard taper inner joint.

  • Synthware Distillation Adapters with Threaded Thermometer Ports

    Kemtech America

    Synthware distillation adapter with threaded thermometer port. The threaded port will accommodate a 6-7.5mm O.D. plain thermometer. The adapter has standard taper top outer joint and inner joints for the bottom and side. All joints are the same size. 

  • Synthware Rotary Evaporator Anti-Splash Traps with Fritted Discs

    Kemtech America

    Synthware rotary evporator anti-splash trap with extra coarse fritted disc. Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. the frit reducesfoam from being carryover. With upper outer and lower inner standard taper joints.

  • Synthware Inlet Adapters with Hose Connection

    Kemtech America

    Adapter has a Nylon compression cap and a Viton o-ring to form a vacuum tight seal. Cap accommodates 5.0 - 7.5mm O.D. thermometer or gas inlet tube. The 8mm hose connection can be used for N2/Ar introduction or vacuum. Supplied with one Nylon cap and one Viton o-ring.

  • Synthware Flushing Adapters

    Kemtech America

    Synthware flushing adapter is used to flush and fill attached vessels with an inert gas to provide protective storage. A ballon is connected to the top hose connection. An inert gas is connected to the side hose connection. The ballon can be expanded with inert gas at the same time as the vessel or…

  • Synthware Vacuum Take-Off Adapters, Short Stem

    Kemtech America

    Synthware vacuum take-off adapter with drip tip. For use in vacuum distillation. Adapter is bent at 105 degrees. Serrated hose connection is attached to vacuum source. With standard taper top outer joint and lower inner joint of the same size.

  • Synthware Distillation Connecting Adapters

    Kemtech America

    Synthware distillation connecting adapter. With standard taper top outer joint and inner joints at bottom and the side arm. Bottom and side arm joints are angled at 75 degrees to one another.

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.