Spinner Flasks

…cultures in sealed flasks by placing on a magnetic stirrer. Nylon bearing sleeve attached to the underside of cap supports Kynar®-coated, stainless steel shaft, with magnetic impeller at lower end, suspended above bottom of flask. Access to contents of assembled flasks provided by screw-cap…

…each spinner flask system assures a clean and sterile unit that is nonpyrogenic. No more concerns with detergent residues or contamination. Compatibility Made of USP Class VI and ISO 10993-18 polystyrene, the vessel is comparable to conventional glass spinner flasks for growth…

Ideal for small working volumes with ph and do probe. 32mm low sidearms for insertion. Size: 1l Center cap size: 100mm 32mm compression fitting probe & port assemblies sold separately Dimensions: 135 x 240mm

Promotes optimal growth of suspension and micro-carrier culture. Impeller height adjust through compression fitting center cap. The indented bottom prevents accumulation of micro-carrier beads under impeller Size: 100ml Sidearm cap: 32mm Od x oal : 65 x 135mm Center neck: 100mm

Replacement Parts For Internal Impeller Assembly Bioprocess Spinner Flasks

Water jacketed, flat bottomed spinner flasks consist of a water jacketed spinner flask, manufactured from Type 1 Class A borosilicate glass, and a microcarrier style impeller with glass shaft that extends through the cap and PTFE paddle. Flasks are typically used with a circulating water bath.…

…gamma-irradiated, each spinner flask system assures a clean and sterile unit that is nonpyrogenic. No more concerns with detergent residues or contamination. Made of USP Class VI and ISO 10993-18 polystyrene, the vessel is comparable to conventional glass spinner flasks for growth of suspension…

Water jacketed, flat bottomed spinner flasks consist of a water jacketed spinner flask, manufactured from Type 1 Class A borosilicate glass. Flasks are typically used with a circulating water bath. Jacket volumes are approximate and flasks are not graduated. Note: Paddle and Cap assembly are…

…Corning® disposable spinner flask system comes ready-to-use with paddle and integrated magnet, eliminating the need for time-consuming assembly or cleaning and reassembly. Made of USP XXXIII Class VI polystyrene, the vessel is comparable to conventional glass spinner flasks for growth of…

Replacement vessel is supplied with black phenolic rubber lined caps for the 18mm side arms, polypropylene caps and pouring rings for the GL-32 and GL-45 side arms.

A range of accessories are available for use with Spinner Flasks.  Sidearm fittings for gas handling can be used to provide gases into larger Spinner Flasks with vertical sidearms during cell culture to enhance the productivity of the cell culture. Together with O₂, temperature, pH…

The Corning 1L spinner flask body is constructed of polystyrene, paddle and shaft from polypropylene and caps from high density polyethylene. All are made of USP Class VI and ISO 10993-18 compliant materials. Recommended working range of 300mL to 1L. Extended paddle design ensures constant…

MicroCarrier spinner flasks with larger paddle design promotes increased optimal growth of suspension and microcarrier cultures. Indented bottom (100mL thru 1000mL) promotes mixing action under the impeller paddle. The 3L version does not have a dimple. The complete system includes a flask with two…

…Reusable Spinner Flasks. The gearhead stirrer motor delivers 14.5 in-lbs of torque and has a maximum speed of 350 rpm. The weight of the motor is 9 lbs (4.1kg). 402614: Direct Overhead Drive 100 mm Center Cap Assembly 100mm Center Cap Assembly for Corning® Reusable Spinner Flasks is…

The Wheaton Magna Flex Spinner Flasks feature a flex-type, bulb-shaped glass impeller that rotates from a fixed position above liquid level around an indentation in the base of the flask. Primarily designed for use with microcarrier cultures, this unique stirring system increases stirring efficiency…

…bottom prevents accumulation of micro-carrier beads under impeller. Size: 3l Sidearm cap: 45mm Od x oal : 165 x 280mm Center neck: 100mm Consist of: 1 1965-13000 mc spinner 3l 1 1965-31000 mc impeller assembly 1-3l 1 1969-73000 glass impeller shaft 3l 1 1965-90100 screw cap assembly 500ml 3l

…bottom prevents accumulation of micro-carrier beads under impeller. Size: 6l Sidearm cap: 45mm Od x oal : 204 x 410mm Center neck: 100mm Consist of: 1 1965-13000 mc spinner 3l 1 1965-31000 mc impeller assembly 1-3l 1 1969-73000 glass impeller shaft 3l 1 1965-90100 screw cap assembly 500ml 3l

…a temperature controller. There are also tubes for addition of media and vent tube. Thermowell assemblies for 1965 and 1967-style angled sidearm flasks, 3-port 5/16" od Thermowell tube,1/4" siphon and vent tubes Includes 45mm pp cap and silicone gasket Seam welded and electropolished 316 l stainless…

Promotes optimal growth of suspension and micro-carrier culture. Impeller height adjust through compression fitting center cap. The indented bottom prevents accumulation of micro-carrier beads under impeller. Size: 250ml Sidearm cap: 32mm Od x oal : 85 x 140mm Center neck: 70mm

Promotes optimal growth of suspension and micro-carrier culture. Impeller height adjust through compression fitting center cap. The indented bottom prevents accumulation of micro-carrier beads under impeller. Size: 15l Sidearm cap: 45mm Od x oal : 294 x 470mm Center neck: 100mm

Ideal for small working volumes with ph and do probe. 32mm low sidearms for insertion. Size: 1l Center cap size: 100mm 32mm compression fitting probe & port assemblies sold separately

Ideal for small working volumes with ph and do probe. 32mm low sidearms for insertion. Size: 500ml Center cap size: 100mm 32mm compression fitting probe & port assemblies sold separately Dimensions: 110 x 175mm

Promotes optimal growth of suspension and micro-carrier culture. Impeller height adjust through compression fitting center cap. The indented bottom prevents accumulation of micro-carrier beads under impeller. Size: 8l Sidearm cap: 45mm ( includes 2 each) Center neck: 100mm Dimensions: 238 x 420mm

Promotes optimal growth of suspension and micro-carrier culture. Impeller height adjust through compression fitting center cap. The indented bottom prevents accumulation of micro-carrier beads under impeller. Size: 6l Sidearm cap: 45mm ( includes 2 each) Center neck: 100mm Dimensions: 204 x 410mm

Promotes optimal growth of suspension and micro-carrier culture. Impeller height adjust through compression fitting center cap. The indented bottom prevents accumulation of micro-carrier beads under impeller. Size: 8l Sidearm cap: 45mm Od x oal : 237 x 430mm Center neck: 100mm

Promotes optimal growth of suspension and micro-carrier culture. Impeller height adjust through compression fitting center cap. The indented bottom prevents accumulation of micro-carrier beads under impeller. Size: 15l Sidearm cap: 45mm ( includes 2 each) Center neck: 100mm Od x oah - 294 x 460mm

Ideal for small working volumes with ph and do probe. 32mm low sidearms for insertion. Size: 3l Center cap size: 100mm 32mm compression fitting probe & port assemblies sold separately Dimensions: 165 x 290mm

Ideal for small working volumes with ph and do probe. 32mm low sidearms for insertion. Size: 500ml Center cap size: 100mm 32mm compression fitting probe & port assemblies sold separately

Promotes optimal growth of suspension and micro-carrier culture. Impeller height adjust through compression fitting center cap. The indented bottom prevents accumulation of micro-carrier beads under impeller. Size: 1l Sidearm cap: 32mm Od x oal : 135 x 250mm Center neck: 100mm

Promotes optimal growth of suspension and micro-carrier culture. Impeller height adjust through compression fitting center cap. The indented bottom prevents accumulation of micro-carrier beads under impeller. Od x oah:410mm x 535mm Center cap: 100mm Sidearm cap: 45mm

Promotes optimal growth of suspension and micro-carrier culture. Impeller height adjust through compression fitting center cap. The indented bottom prevents accumulation of micro-carrier beads under impeller. Size: 3l Sidearm cap: 45mm ( includes 2 each) Center neck: 100mm Od x oah - 165 x 280mm

Ideal for small working volumes with ph and do probe. 32mm low sidearms for insertion. Size: 3l Center cap size: 100mm 32mm compression fitting probe & port assemblies sold separately