Schlenk Manifold

…and is supplied with a 14/20 outer joint cap style stopper. Pre-trap is 51mm OD x 250mm long with two 28/15 socket joints which connect the manifold and main trap assembly which have 28/15 ball joints. Main trap body is 58 mm OD x 235mm long with a reversed 75/50 ball and socket joint connection.…

This borosilicate glass Air-Tite vacuum gas manifold (Schlenk line) is designed with double oblique pressure/vacuum stopcocks with 4mm bores and a 16.2/56 plug size. The stopcocks simplify evacuation or pressurization with an inert atmosphere. Manifold is 1" O.D.

Used to purify and transfer solvents under inert conditions. Permits transfer of solvents directly into an evacuated storage vessel with 24/40 standard taper outer joints. A 0-4mm Chem-Vac™ Chem-Cap® valve is used for vacuum control.

…same main and pre-trap as the AF-0450 line. Overall dimensions are 34" W x 24" H. Complete system consists of one 4-port vacuum/inert manifold, one pre-trap, one main trap assembly, one main trap body, two CG-150-05 #28 S.S. pinch clamps, one CG-150-08 #50 S.S. pinch clamp, one CG-150-21…

Double bank manifold available in 3, 4 or 5 port configuration. Forward facing 0-8mm Chem-Vac™ Chem-Cap® valves permit easy operation of manifold inside of a fume hood. Main ports are spaced 100mm center to center with an additional 2 ports on the upper bank that can be used for gauging or…

…vacuum manifold with 0-8mm Chem-Vac™ Chem-Cap® valves mounted on a 45° angle to the user permitting easy operation inside of a fume hood. Ports are spaced 75mm center to center. All connection ports are #15 o-ring connections that incorporate a greasefree o-ring seal. Manifold is…

…design, double bank manifold with the valves sealed in a vertical position. This design permits the user an unobstructed view of whether the valve is in the open or closed position while also exposing the PTFE valves to less outgassing (when the front bank of the manifold is used for inert gas).…

…AND AF-0455 ADAPTERS MUST BE PURCHASED SEPARATELY. All four ends of the manifold have #15 o-ring joints permitting the trap assembly to be attached to either the right or left side of the vacuum bank. Manifold is supplied with two AF-0210-01 #15 stoppers and three AF-0070-05 #15 o-ring joint…

For use with the AF-0060 or AF-0061 manifolds or any Airfree® component with an o-ring as a closure. Supplied complete with one Viton O-Ring.

Adapters for use with manifolds such as AF-0450 through AF-0454 to permit port connection to standard rubber hose. Adapters have hooks just below the grind for use with CG-110 stainless steel springs. The 24/40 size is available with a constriction above the serrated hose connection to permit bowl…

These borosilicate glass Schlenk sample tubes incorporate a grease-free high vacuum 0-4mm valve and are suited for pressure/vacuum applications. Ideal for reaction and storage of air-sensitive compounds. Sidearm can be connected to inert atmosphere/vacuum source or a manifold.

…the sidearm and a Chem-Vac™; Chem-Cap®; valve to control gas or liquid flow into the vessel. All sizes are of heavy wall construction, and are used with AF-0060 and AF-0061 manifolds or any other Airfree® component with a #15 o-ring joint. Supplied complete with one #116 Viton o-ring.

…and a Chem-Vacé; Chem-Cap®; valve to control gas or liquid flow into the vessel. Vessels are constructed of medium wall tubing and are used with AF-0060 and AF-0061 manifolds or any other Airfree®; component with a #15 o-ring joint. Supplied complete with one #116 Viton o-ring.

…the trap stopper and body is made with a 57mm flat o-ring flange for total grease-free operation when used with either the AF-0060 or AF-0061 manifolds. Trap body is 57mm OD x 300mm in length to be used with a 4,300mL dewar flask (CG-1593-05 or CG-1594-05). Complete item consists of the trap stopper…

A 0-12mm Chem-Vac™ Chem-Cap® valve having an o-ring joint for connection to the right hand side of AF-0300-03 vacuum manifold. Adapter is available for #15, #25, and #30 o-ring joints. Complete gauge consists of a glass portion, a S.S. bushing drilled and tapped for 1/8 " NPT…

…of bubbler allows for fine control of purge gas within an inert gas system such as a manifold. Purge gas enters bubbler through hose connection (A) and exits thru connection (B) which is connected to manifold. The large capacity of the main chamber (C) allows for rapid purging with check valve…

…with AF-0060 thru AF-0062 vacuum manifolds that permit the manifold to be utilized with a multitude of standard glassware or tubing products. The AF-0070 adapters are to be used with either a Cajon® fitting on the main ports or at the ends of the manifold with heavy wall rubber vacuum tubing.…

…thermocouple adapter. Both traps can be isolated from the manifold or pump via 0-12mm Chem-Vac™; Chem-Cap®; valves (H). Trap assembly is designed to allow connection to either the right or left side of AF-0060 or AF-0061 manifolds. Complete item is supplied with one #331 Viton o-ring, one…

… The manifold is connected to the dual trap assembly via a 35/20 ball joint with a 0-12mm Chem-Vac™; Chem-Cap®; shutoff valve (G) to isolate the line from the traps. The pre-trap (H) is 50mm OD x 205mm in length and has two 35/20 socket joints to connect it to the manifold and main…

…pump to the pumping circuit. Pump oil listed is Dow Corning #704. PLEASE NOTE: WHEN ORDERING THE DIFFUSION PUMP TO MATE WITH THE AF-0450 MANIFOLD, PLEASE USE THE SAME CODE FOR BOTH ITEMS. FOR EXAMPLE: AF-0460-01 LEFT HANDED DIFFUSION PUMP SHOULD BE ORDERED WITH AF-0450-01 RIGHT HANDED MANIFOLD.

…the #15 o-ring joint and the standard taper inner joint. Frit permits filtration of large particles before introduction into the flask and also serves as a bump trap for reactions being performed in flasks while connected to the manifold. Each adapter is supplied complete with one #116 Viton o-ring.

Vacuum, NO-AIR adapter for vacuum cart, vacuum manifolds and Schlenk lines. Has No. 15 O-Ring joint side port with a Hi-Vac valve for precise flow control and an ACE-THRED bottom outlet.

…cooler operation Address a wide variety of laboratory vacuum needs with these rugged oil-seal pumps. Use DuoSeal vacuum pumps for Schlenk drying manifolds, freeze drying, vacuum ovens, glove boxes, degassing, concentrations, distillations, and more. DuoSeal pumps are built to rigorous…

…remove condensable vapors between runs for repeatable top performance and extended diaphragm life. Applications include: Schlenk line drying manifolds Vacuum ovens Freeze dryers up to 6 L Centrifugal concentrators Many other deep vacuum applications Save the time,…

…glass addition funnel. Has either a 2mm glass stopcock or a 0-3mm inlet valve side arm. Has an outer standard taper joint top. Funnel has a 0-4mm Hi-Vac valve bottom outlet ending in an inner standard taper joint. Ideal for Schlenk lines or using to connect or add on to vacuum and NO-AIR manifolds.