Rotary Evaporator Trap

Compare Tool

Select up to 3 products

Rotary Evaporator Trap
1 - 32 of 55
Sort
View
Show
  • Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With upper outer and lower inner standard taper joints.

  • These PYREX® traps are used in rotary evaporators. They have a round body with upper and lower stems. The lower stem has a Standard Taper inner joint at the bottom and extends upward inside the body. The closed top of this stem has two side openings. The upper stem has a Standard Taper outer joint.

  • Fritted Bump Trap for a Rotary Evaporator

    DWK Life Sciences (Kimble)

    This trap has a 40-60 micron porosity fritted disc sealed between the lower inner and top outer joint to prevent the contents of the flask from entering into the condenser in the event of bumping. All traps have a Standard Taper 24/40 top outer joint Manufactured from 33 expansion, low…

  • Rotary evaporator bump trap is used between the vapor tube and evaporation flask on a rotary evaporator to prevent contents of the flask from being drawn into the condenser in the event of “bumping”. Unique elliptical shape provides large trap volume while decreasing the overall length…

  • …components for model R220 rotary evaporators. Traps are both inner and outer cold traps available either safety coated or plain. This improved version utilizes flat ground flanges on the inner and outer trap that is sealed together with a Duran quick- release clamp. Outer traps are supplied with two…

  • Bump trap for use between the rotary evaporator's steam tube and evaporator flask, preventing fluid from being drawn into the condenser.

  • Trap provides expanded volume for reactions that have a tendency to foam excessively. The inner vapor tube is sealed to the top of the trap to prevent entry into the condenser. Traps have a 24/40 top outer joint and the listed size of lower inner joint.

  • …inside pump heads. An inlet separator traps ejected condensed solvent vapors. A self-cleaning purge automatically runs for two minutes at shut-down to expell unwanted residue, extending the diaphragm life. Use with rotary evaporators up to 5 L capacity. A cold trap, such as Welch 1420H-14 (7893R90)…

  • Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With two 4mm drain holes at the base of the inner tube to allow solvent to drain back into the evaporation flask. Has upper outer and lower inner standard taper…

  • The rotary evaporator R-100 is a high-quality, entry level Rotavapor to meet the essential needs in classical laboratory applications. It is capable of a manually adjustable rotation speed of 20 to 280 rpm and equipped with an action jack lift for manual lifting of the evaporating flask. Included is…

  • Foam-Type Distillation Traps

    DWK Life Sciences (Kimble)

    …foaming-type reactions from entering either the distilling column or the condenser. Useful with rotary evaporators 517000 features a more extensive baffle system than other traps Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438,…

  • PTFE connecting adapters and glass conversion adapters for connecting GPI threaded vials to a rotary evaporator vapor tube or trap. Both are suitable for vacuum work. PTFE connecting adapters are available with FETFE or Chemraz o-rings. Order Chemraz if you are using Methylene Chloride or Acetone.…

  • …holder. Glass Cold Trap (Dry Ice) Condenser High quality glass cold trap (dry ice) condenser with lid. No chillers needed, utilizes dry ice for optimal efficiency. Designed and specially made for Ai 2L or 5L SolventVap rotary evaporators. Rotary Evaporator Vapor Duct with Sealing…

  • Synthware rotary evaporator trap. Anti-climb design. Trap provides expanded volume for reactions that have a tendency to foam excessively. The inner vapor tube is sealed to the top of the trap to prevent entry into the condenser.

  • Bump trap for use between a rotary evaporator's steam tube and evaporator flask, preventing fluid from being drawn into the condenser. Improved design incorporates two drain holes to expedite the return of solvent to the evaporator flask.

  • Synthware rotary evporator anti-splash trap, modified. With extra coarse porosity fritted disc sealed above lower inner joint. Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. Frit reduces foam overflow from being…

  • Adapters permit the connection of standard laboratory dram sample vials directly to the vapor tube or a bump trap of a rotary evaporator. Adapters have a top outer joint of the listed size and a 20-400 G.P.I. thread at the bottom. A PTFE-lined, polypropylene, double-threaded connector attaches the…

  • …dry ice condenser-trap,for Rotary Evaporator use. Squatty design 18"high, two chambers. Dry ice fingers secured in main body via #50 Ace-Thred, bushings, and O-Rings allowing for easy cleaning. Two ports at top of chamber are 3/8" O.D. (for connecting to evaporator & vacuum source). Bottom stopcock…

  • Two piece cold trap style condenser for use with rotary evaporators. Condenser has a 50mm flange on the side, a 35/20 lower ball joint, a 19/38 stopcock plug and removable hose connections using GL-14 threads. Condenser is supplied complete with PTFE centering ring along with plastic caps and…

  • Two piece cold trap style condenser for use with rotary evaporators. Condenser has an additional 19/38 outer joint sealed onto the condenser to allow continuous feed of volumes exceeding the capacity of the evaporating flask. The 19/38 joint is sealed at an angle which allows the condensate to fall…

  • Dry Ice Cold Traps are recommended for pumps when doing rotary evaporation, drying solvents, vacuum distillation, centrifugal concentration or any other process involving volatile solvents. 2.8 L center well that holds a dry-ice and alcohol slurry capable of producing temperatures as low as…

  • Replacement glassware for Buchi rotary evaporators. Available with either a plain or safety coated outer trap. Outer trap bodies, codes -01 and -03 do not include a plug. Order separately 1 each 13295-10.

  • Bump Traps

    Chemglass

    Used between the vapor tube and evaporation flask on a rotary evaporator to prevent contents of the flask from being drawn into the condenser in the event of “bumping.” Traps have a 24/40 top outer joint and the listed size of lower inner joint.

  • Synthware rotary evporator anti-splash trap with extra coarse fritted disc. Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. the frit reducesfoam from being carryover. With upper outer and lower inner standard taper…

  • …gas flow to efficiently evaporate samples in standard 20mL scintillation vials. The technique eliminates the need for a vacuum pump or a large supply of blow down gas, significantly reducing cost, complexity, noise, andmaintenance compared to rotary evaporators, vacuumcentrifuges, and conventional…

  • …bump trap. For use in Rotary Evaps between the steam tube and the evaporator flask. Prevents fluid from being drawn into the condenser. Shape allows for the same effect as standard traps but with less space between the flask and evaporator tube. This allows for use of larger flasks in the Rotary

  • Upper tubulation prevents migration of film and foam directly into the condenser.

  • Vapor tube/bump trap adapter is designed to be used with the Büchi® R-200/205 rotary evaporators. This adapter combines a vapor tube adapter and a bump trap. Trap has an extra coarse fritted disc sealed between the lower inner joint and the top flange. Adapters have a 50mm OD top flange…

  • Self washing, rotary evaporator trap design by Dr. William Boulanger. Superior design prevents blow-through and enables continuous addition with rotary evaporators. Solvent vapor rapidly flows out while condensed solvent continuously rinses both the trap walls and the evaporator shaft returning any…

  • Glass purge adapters for use with popular brands of rotary evaporators. Top has 35/25 socket joint for joining with the trap or condenser. The bottom has a 35/25 ball joint for connecting to the receiver flask. The middle or purge tube has either a 2mm PTFE stopcock or a 2mm valve to allow for…

  • PTFE adapter allows convenient connection of a Microwave vial to a Rotary Evaporator Bump Trap having a standard taper joint size. Lower portion incorporates a threaded black Acetal compression cap that is slotted to accept the flange fitting on the vial.

  • Replacement glassware for Buchi rotary evaporators. The C glassware set is the most popular and is available with either a plain or safety coated outer trap. Outer trap bodies, codes -01 & -03 do not include plugs. Order separately 1 each 13295-08 and 1 each 13295-10.

Compare Tool

Select up to 3 products

Please Log In

Don't have a web profile? Create one now.