Chemglass
-
Autosampler Headspace Vials
ChemglassThese vials are manufactured from Type 1 Class A Borosilicate glass. The standard flat bottom vials can be used with Hewlett-Packard, Carlo Erba and Shimadzu. The European 20mm aluminum seal vials with rounded bottoms can be used in Perkin-Elmer, Tekmar, CTC/L.E.A.P.™ Technologies,…
-
Extra deep baffle indents on the lower outside edge of the flask to maximize oxygen transfer to the culture medium when used on an orbital shaker. Delong style neck is made to fit stainless steel or plastic closures, while the longer neck reduces the amount of splashing that would reach the closure.
-
Jacketed large scale process reaction vessels. The 10, 15, and 20L vessels have a 200mm ID flange with an o-ring groove formed in the surface of the flange. The 30, 50, 75, and 100L have a 300mm ID flat ground flange. The inlet/outlet of the vessels are beaded pipe fittings for use with the CG-1964…
-
Universal Stirrer Shaft Coupling
ChemglassUniversal Stirrer Shaft Coupling incorporates a universal joint to compensate for misalignment of drive motor and glass stirrer shaft. Nylon bushing compresses around shaft using an allen screw. Steel stud attaches directly to the chuck of a stirrer motor. Supplied complete with an allen wrench. …
-
Reaction Vessel Lids, 6-Necks, 200mm
ChemglassSix-Neck lid for 200mm flanged vessel. Lid has 45/50 center neck, four 45/50 side necks and a 60mm angled flange for powder addition. PLEASE NOTE: 60MM LID, O-RING AND CLAMP MUST BE ORDERED SEPARATELY.
-
Corning Cover slips are manufactured from Corning 0211 Float Glass, #1.5 thickness (0.16 to 0.19mm). Sold in packages of 1oz.
-
Septum Stoppers, Sleeve Type
ChemglassSleeve type stoppers with a hollow plugs and sleeve extensions that folds down over the neck of a vessel, tubing, etc. The diaphragm can be punctured with a syringe needle, re-sealing after the needle is withdrawn. Available in either RED or WHITE rubber.
-
These convenience packs come with 100 bonded closures and vials packed seperately. Closures with bonded septa are not attached.
-
PIE-BLOCK Reaction Block System
ChemglassSafety Pie Plate Holder keeps up to Four pie wedges securely locked together on the hotplate Aluminum construction provides excellent heat transfer while not interfering with the magnetic field Interchangeable pie wedges permit various sized vials or flasks on one hotplate Holes are spaced…
-
Round Cover Slips
ChemglassCover slips are manufactured from the highest quality borosilicate hydrolytic class 1 German glass. They have excellent resistance to chemicals and are ideal for neural tissue culture and hard-to-attach cells. These cover slips are exceptional for florescence and confocal microscopy. Sold in…
-
Heavy Duty Clamp Holders
ChemglassHeavy duty epoxy coated alloy clamp has high tensile strength and corrosion resistance. Can be used to support stirrers, temperature monitors and condensers. Large hand knobs allow easy adjusment and secure clamping power. Useful wherever clamping at 90° is required.
-
-
Removable Hose Connections, GL Threads
ChemglassPolypropylene hose connections with a Viton rubber seal for use with GL-14 or GL-18 glass screw threads for working temperatures up to max +110°C. Enables the connection of cooling or vacuum hose by simply screwing either style (straight or bent) onto the glass thread instead of forcing Tygon…
-
Foam Plugs for Test Tubes
ChemglassFOAM PLUGS FOR TEST TUBES AND LABORATORY FLASKS, INDENTI-PLUGS, Economical Open-cell, 1.45 lb. uniform-density foam Breathable and non-absorbent Use over a wide temperature range Autoclavable Chemical resistant Proven safe for algae culturing Identi-Plugs® are…
-
Adapters, Distillation, 75°
ChemglassWith standard taper inner joints at a 75º angle to one another.
-
Extraction Apparatus, Soxhlet
ChemglassSoxhlet type extraction apparatus used for continuous extraction of solids with a suitable solvent. Extractor uses paper or CG-1372 glass thimbles. Condenser has an enlarged uptake tube to improve condensing capacity. Complete apparatus consists of an Allihn condenser, extractor and flat bottom flask.
-
Used to regulate the flow of gases or liquids into reaction systems. Stopcock has a bore of 2mm, and has an internal needle valve which permits for fine control of gases or liquids added to reactions. Hose connection has an O.D. of 8mm at the middle serration.
-
Our controllers feature solid-state proportional voltage power control in a compact benchtop design. Controllers provide accurate manual control of heating mantles, tapes and all other resistive loads with an adjustable output range from 5 to 100% of the rated voltage. All units are supplied with a…
-
Reaction Vessel Lids, PTFE, 150mm
ChemglassReaction vessel lid is constructed entirely of PTFE. Low-form lid has nine openings: (A) center neck 1"; female NPT for PTFE standard taper adapter, (B) side necks 1"; female NPT, vertical for PTFE standard taper adapters, (C) side neck 1"; female NPT with 10° X 10° compound…
-
Clear Glass 1.5mL High Recovery Vials
ChemglassWith a 40% larger opening, this vial is specifically designed to work in robotic arm auto samplers. They also incorporate the unique Step Vial design that precisely centers a limited volume insert in the neck of the vial.
-
Adapters, PTFE, Universal, Inlet
ChemglassUnique adapter is made entirely of PTFE and is supplied complete with a series of 5 all PTFE ferrule style cones. These cones have inside diameters that run from 3.5 to 6.5mm and seal against the inserted tube by means of a threaded compression screw. Cones are color coded for easy identification.…
-
Eco Funnels, 8 Inch
ChemglassThe 8" Eco Funnel is make of HDPE and has a 2000mL fluid capacity. Features an easy to use lid, gasket and positive latch to close the lid and maintain an airtight seal. A filter is also built into the interior to reduce the loss of magnetic stir bars and other items when emptying the contents…
-
Filter Tubes, Allihn
ChemglassAllihn type filter tube with a 30mm O.D. disc. Height above the disc is 100mm, lower stem is 8mm O.D. x 55mm in length.
-
Glass Plug Straight Bore Stopcocks
ChemglassThe 2mm through 6mm bore sizes are supplied complete with the listed size metal retaining clip CG-423. The 8mm and 10mm bore sizes are supplied with a #29 and #34 CG-145 Keck clip respectively.
-
Amber Sample Vials, with Caps
ChemglassAmber sample vials packaged in convenient LAB-PACS of 144 pieces. Made from Type I borosolicated glass. Full height partitions minimize breakage. Solid PTFE lined caps. Open top caps with septa are available under part number CG-4910.
-
Norell Screw Cap NMR Tubes
ChemglassNORELL™ Screw Cap NMR Tubes have a convenient screw cap access with the security of a PTFE® seal. Supplied with open top cap & PTFE® septum for quick and clean access with a 22 gauge standard point needle.
-
Midget Bubblers, Graduated
ChemglassMicro impinger designed for sampling of small volumes of air at low jet velocity, as per EPA Method 6. Impinger bottle is graduated from 5 to 30mL in 5mL subdivisions. Both the bottle and stopper have 24/40 standard taper joints. The nozzle being replaced with an extra coarse fritted gas dispersion…
-
Adapter, Distilling
ChemglassAdapter is used to connect distilling column with vertical condensers. With standard taper outer joint at the top for use with 10/18 or 10/30 jointed thermometers. Both lower inner joints are the same size. Side arm is at a 75º angle to the vertical tube. For thermometers see CG-3506-N.
-
Bubbler has an integral valve to control the flow of inert gas into the system. Bubbler requires a minimal amount of oil due to the inner tube being within 5mm of the bottom. Both sidearms are 9mm OD for use with 3/8" Cajon®; fittings. Overall height is approx. 220mm.
-
Similar to AF-0509, adapter has a T-Bore stopcock permitting vessels having a standard taper outer joint to be purged and evacuated. Available with a choice of a 4mm glass high vacuum stopcock having a S.S. constant pressure retention device or 4mm PTFE stopcock.
-
Heavy wall, wide mouth flask with a GL80 glass thread and a 24/40 connecting adapter. Flasks have a heavy wall for vacuum applications and are balanced to prevent run-out during rotation. Unique design makes it easier to handle highly viscous liquids, powders, and solids. The large opening permits…
-
Reservoir for use with CG-1192 and CG-1193 columns. Reservoir has a top 24/40 standard taper outer joint for use with CG-1195 flow controller, and the listed size lower inner joint. Supplied complete with one CG-182 open top cap, one CG-305 Viton o-rin
![Site Search powered by SLI Systems](http://assets.resultspage.com/logos/sli_logo_2014.png)