Distillation Adapters

Compare Tool

Select up to 3 products

Distillation Adapters
1 - 32 of 99
Sort
View
Show

United Sci Supplies

  • Glass Vacuum Adapters

    United Scientific Supplies

    Vacuum adapters have 24/40 joints. Bent adapter has a 105° angle between the top outer joint and bottom inner joint. Straight adapter has a top outer joint and bottom inner joint. Both adapters have 24/40 joints and include a 3/8" hose connector.

  • Synthware Tapered Distilling Adapters

    Kemtech America

    With an outer standard taper joint at the top. The tapered delivery drip tube extends into open receivers.

  • Synthware Distillation Adapters, 75°

    Kemtech America

    Synthware distillation adapter bent at 75 degrees. Both ends are standard taper inner joints and are the same size.

  • Tube 24/40

    Corning

    These PYREX® connecting distilling tube adapters have full-length inner 24/40 Standard Taper joints of same size. The connecting arm is approximately at a 75° angle from vertical and is 200mm long.

  • Adapter, Distilling

    Ace Glass

    For connecting distilling column with vertical condensers. Top joint 10/30 is for 76 mm immersion thermometer. Side arm at 75 degree , vertical side arm 17.8cm from center tube.

  • 75° Bent Distillation Adapters

    DWK Life Sciences (Kimble)

    Ideal for use as a stillhead adapter. With Standard Taper inner joints at each end Both joints are of the same size Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements

  • Kjeldahl Trap Adapters

    Kemtech America

    Synthware distillation adapter with Kjeldahl trap. With two standard taper inner joints that are parallel and at a 75 degree angle to the connecting tube. Distance between joints is approximately 200mm.

  • 3-Way Adapters

    United Scientific Supplies

    3-Way adapter has a 75° angle sidearm with inner joints on the sidearm and bottom and an outer joint on the top. Inclined adapter has a 105° angle sidearm with outer joints on the sidearm and top and an inner joint on the bottom. Both adapters have 24/40 joints.

  • Synthware Distillation Adapters, Vigreux

    Kemtech America

    Synthware Vigreux distillation connecting adapter. Indenstations in lower section improve liquid/vapor contact. The standard taper top outer joint accomodates a 76mm immersion thermometer. Bottom and side joints are standard taper inner joints.

  • Synthware Distillation Adapters, Vacuum Jacketed

    Kemtech America

    Can be used as a distilling head to connect a condenser to the top of the distillation column. The 10/18 top joint accomadates a 76mm immersion thermometer.

  • PYREX Vacuum Distilling Adapter, with Extended Drip Tip

    Corning

    With outer Standard Taper joint at the top and an inner-sealed through drip-tip joint at the bottom Bent at 105° angle The serrated sidearm is 10 mm O.D. drip-tip at the bottom extends about 20 mm below the lower end of the joint

  • Distillation Adapter, Claisen

    DWK Life Sciences (Kimble)

    Provides dual entry into a variety of flasks BEVEL-SEAL adapters allow temperature measurements at either top outer opening. Useful for reflux with addition- type reactions. Adapter consists of two female standard taper joint fittings at the top and one male standard taper joint at the bottom.…

  • Synthware Distilling Adapters, 75°

    Kemtech America

    Synthware distilling adapter with top compression cap. With same size standard taper inner joints on bottom and side arm. Cap accomodates 5.0 - 7.5mm O.D. thermometer. Supplied with one Nylon cap and one Viton o-ring.

  • Connecting Distillation Adapters

    DWK Life Sciences (Kimble)

    Useful in the sub-boiling separation of mixtures having volatile components. Standard Taper inner joints are parallel Joints are the same size Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements

  • Synthware Distillation Connecting Adapters

    Kemtech America

    Synthware distillation connecting adapter. With standard taper top outer joint and inner joints at bottom and the side arm. Bottom and side arm joints are angled at 75 degrees to one another.

  • 75° Connecting Distillation Adapters with BEVEL-SEAL™

    DWK Life Sciences (Kimble)

    Used in distillation assemblies where adjustable immersion depth of the thermometer is desired. Threaded top BEVEL-SEAL™ connection for plain stem thermometers Vacuum-tight seal is achieved with the open top compression cap and FKM o-ring BEVEL-SEAL™ cap 410119-1307 is…

  • SYNTHWARE Distillation Adapter

    Kemtech America

    Distillation Adapter, Microscale, Synthware, Joints: 14/10, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.

  • Adapters, Standard Taper Joints

    Ace Glass

    A general line of adapters supplied with inner joints to be used in assemblies for distillation, extraction or your own requirements. On codes -14 and -22, please specify capacity and catalog number of item into which the adapter is to be placed. When

  • Adapter, Distilling

    Ace Glass

    With outer joint and external thread at top for making an O-RING-CAP-SEAL connection with mating male joints, inner joint at bottom and at 75 degree angle. Supplied with cap and O-Ring.

  • Synthware Kjeldahl Distilling Trap Adapters

    Kemtech America

    Adapter is placed above flask to prevent carry-over of reactions which have a tendency to foam. With top outer and lower inner standard taper joints.

  • PYREX® Distilling Tube Adapters

    Corning

    60° angle Three Standard Taper 24/40 joints Approximate length 206 mm This tube is also a replacement for organic chemistry kits. Type I, Class A borosilicate conforming to federal specification DD-G-54 lb and ASTM E 438. Also meets the US Pharmacopoeia specs for Type I borosilicate glass.

  • 105° Bent Distillation Adapters

    DWK Life Sciences (Kimble)

    Barbed hose connection Standard Taper inner joint with drip tip at the bottom and Standard Taper outer joint at the top Joints are the same size Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements

  • Synthware Distillation Adapters

    Kemtech America

    Adapter is bent 105 degrees. The top outer and lower inner standard taper joints are the same size.

  • Distillation Bent Adapters with Tapered Drip Tube

    DWK Life Sciences (Kimble)

  • Synthware Vacuum Distilling Adapters

    Kemtech America

    With two standard taper inner joints that are parallel and at a 75 degree angle to the connecting tube. Distance between joints is 100mm.

  • Adapters, Joints

    Ace Glass

    A general line of adapters supplied with inner joints to be used in assemblies for distillation, extraction or your own requirements. On codes -14 and -22, please specify capacity and catalog number of item into which the adapter is to be placed. We wi

  • Adapter, Vacuum Take-off, 175mm Long Stem

    Ace Glass

    Outer standard taper joint at angle of 105 degree. Used with distillation set-ups. With long stem. Hose connection opposite joint. Stem below joint is 175mm.

  • Synthware Distilling Adapters, 105°

    Kemtech America

    Synthware distillation adapter with sealed in drip tip. Adapter is bent at 105 degrees. Standard taper top outer joint and lower inner joints. 

  • Synthware Distillation Adapters

    Kemtech America

    Synthware distillation adapter with a 10/18 standard taper outer joint for a 76mm immersion thermometer. The adapter has a standard taper top outer joint and inner joints for the bottom and side.

  • 75° Connecting Distillation Adapters

    DWK Life Sciences (Kimble)

    Connecting 75 degree distillation adapters. For use as a component in atmospheric or vacuum distillations. Lower and sidearm joints are inner Standard Taper joints; upper joint is outer Standard Taper joint Joints are same size Manufactured from 33 expansion, low extractable…

  • 105° Bent Distillation Adapters

    DWK Life Sciences (Kimble)

    Bent 105 degree distillation adapters. Standard Taper inner joint at the bottom and Standard Taper outer joint at the top Joints are the same size Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements …

  • PYREX angled Distilling Adapter

    Corning

    … The arms are appraoximately 105° apart One end is equipped with an outer Standard Taper joint and the other end with an inner Standard Taper joint of the same size Used as a receiver adapter 3941S38 is a receiver adapter with a vacuum connection. Vacuum tube O.D. is 10 mm.

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.