Pyrex Glass Bottle

…for handling and storing sterile culture media and sera where stability of the glass is of prime importance. Serum bottles are also suitable for storing distilled water and standard solutions. PYREX bottles have the strength to withstand hot air (dry) or steam (wet) sterilization. Necks…

These bottles are designed for storage of solutions and are ideal for media preparation. The 9.5L (2.5 gallon) and 13.25L (3.5 gallon) sizes are in a conventional bottle shape. The 19L (5 gallon) and 45.5L (12 gallon) sizes are similar in design to a carboy. The 19L size is weight controlled to 15…

Heavy wall Screw cap Particularly useful in handling sputum specimens, this bottle enables digestion, shaking, neutralizing and centrifuging to be performed in one container. The tight-fitting polypropylene screw cap with Teflon® liner reduces the possibility of aerosol escape.

Four sizes Borosilicate glass Wet or dry sterilization These PYREX roller bottles are available in four cell growth areas: 840, 1170, 1330 and 1585 cm 2 . Roller bottles are manufactured from borosilicate glass for the strength to withstand repeated wet or dry sterilization as…

Short length external Standard Taper joints PYREX low form weighing bottles have an external Standard Taper joint style opening. The closure style cap fits over the externally ground body.

PYREX® Suitable for storage of distilled water and standard solutions Of borosilicate glass All have heavy, welted neck but vary in size and shape. Bottles take stopper number 12. PYREX bottles are tough and reliable yet designed with safety in mind. PYREX bottles can withstand…

Short length Standard Taper joints Capacities from 35 to 82 mL These PYREX low form weighing bottles have a Standard Taperjoint style opening that accepts a closed bottom, hollow pennyhead style stopper.

Short length external Standard Taper joints PYREX® Parr weighing bottles are designed for use in weighing small samples. The closure style cap fits over the externally ground body.

Short length external Standard Taper joints These PYREX standard weighing bottles have an external Standard Taperjoint style opening. The closure style cap fits over the externally ground body.

Capacity 3 1/2 gallons With 6-mm-bore, Teflon stopcock and overflow tube which takes 1/2” tubing Takes rubber stopper No. 11 1/2 Useful as a delivery/ storage container for solutions. Height 17 3/4”.

Recommended for use in preventing contamination by solubility or pH change With dropping bulb and pipet, Standard Taperground-glass stopper Stopper for 30 mL size is not standard Standard Taper. IMPORTANT: stopper is not covered by Standard Taperspecifications, but ground to an…

Short length Standard Taper joints Capacities from 7 to 85 mL These PYREX tall form weighing bottles have a Standard Taperjoint style opening that accepts a closed bottom, hollow pennyhead style stopper.

PYREX® Brand Drechsel Standard Taper stopper incorporates a plain dip tube as the distributor Large hexagonal base for stability Standard Taper stopper size 29/42

… Normal working temperatures for PYREX brand boiling flasks is 230°C Precisely tooled for uniform stopper fit Reinforced rim increases mechanical strength These flasks are used in applications requiring rigid stoppering and as wash bottles in routine lab washing Designed for…

…PYREX wide mouth storage bottles are designed as both heavy-duty storage and mixing and sampling bottles.  The extra wide mouth (69 mm inner diameter) gives easier access for pouring and removing pastes, powders and larger items. The neck opening is 5 times larger than on GL45 threaded bottles…

These 840cm2 PYREX® roller bottles are manufactured from borosilicate glass for optical clarity and mechanical strength and can withstand repeated wet or dry sterilization. All bottles have linerless, one-piece orange polypropylene plug seal caps with GL4

These 2mL PYREX® specific gravity bottles are unadjusted for calibration in the laboratory.

These 500mL PYREX® gas washing bottles are replacements for 31760-500EC (5632D58) and 31760-500C (5632D64) These bottles have large hexagonal bases for stability

…125mL PYREX® gas washing bottles provide an inexpensive but effective method for washing and drying gases. Bottles have large hexagonal bases for stability Sidearm tubulations are 8mm O.D A 29/42 Standard Taper stopper is used to seal the top to the base These bottles are a…

These 350mL PYREX® gas washing bottles provide an inexpensive but effective method for washing and drying gases. Sidearm tubulations are 10mm O.D. The side inlet tube on this bottle has a rod sealed to the bottle near the top for extra strength. A 24/40 Standard Taper stopper is used to seal the…

4565F10 will fit tubes up to 20 mm o.d. (without lip); outer mantle i.d. is 25 mm and inner tube o.d. is 8 mm; overall height: 70 mm 4565F25 can be used on bottles with maximum rim diameter of 44 mm; outer mantle i.d. is 45 mm and inner tube o.d. is 10 mm; overall height:   85 mm

…PYREX® Washing Bottles With fused-on fritted cylinder 12 mm diameter on inlet tube and with Standard Taper 29/42 joint. With glass hooks on both bottle and cap, but without springs. Offered in 250 and 500 mL capacities, in coarse (C) and extra coarse (EC) porosities. 250EC and 250C bottles…

Heavy-duty bottle of low actinic glass is valuable for storing or transporting light sensitive materials. Bottle includes a linerless, one-piece autoclavable, orange polypropylene plug seal cap with drip-free pouring rings.  Glass beads indicate full capacity line. Permanent white enamel…

…mouth PYREX® with glass stopper With ground neck With ground glass stoppers 125 mL and 250 mL bottles are furnished with a number 19 Standard Taper stopper; 500 mL bottles are furnished with a number 24 Standard Taper stopper; 1,000 mL and 2,000 mL bottles are furnished…

For user convenience, PYREX Erlenmeyer flasks are graduated to show approximate capacity. The 25- 50- and 125 mL flasks are satisfactory for use as a weighing bottle. Erlenmeyer flasks come with a PYREX Standard Taper stopper.

… These PYREX® round bottom boiling flasks have short ring necks. These ring neck boiling flasks are precisely tooled for uniform stopper fit. The reinforced rim increases mechanical strength. These flasks are used in applications requiring rigid stoppering and as wash bottles in routine lab…

Screw cap graduated bottles can be dry heat sterilized to 180°C when used with optional Melamine resin caps 1743E90 and ETFE pouring rings 1743E95.

…media bottle can be used for storage as well as mixing and sampling. Includes linerless, one-piece autoclavable polypropylene plug seal cap with drip free pouring rings. Optional red PBT caps and red ETFE pouring rings are available for dry heat sterilization (180°C).  New glass bead…

These 42mL PRYEX® low form weighing bottles have an external 60/12 Standard Taper joint style opening. The closure style cap fits over the externally ground body.

Chemical and thermal resistant Graduated Screw cap Bottles are made from PYREX® borosilicate glass for enhanced chemical and thermal resistance. Square bottles are easy to handle, take up less space (13-20%) on the shelf or autoclave and are ideal for mixing, sampling and…

…refrigerators, autoclaves. Bottles are graduated to their full working volumes Available in four sizes: 125 mL, 250 mL, 500 mL, and 1 L Pyrex Slim Line bottles are made from the same Type 1 Class A (ASTM E-438) borosilicate glass as standard Pyrex media bottles for chemical and heat…

PYREX® borosilicate glass Useful as a delivery/storage container for solutions Autoclavable Features a tubular sidearm outlet to facilitate attachment of flexible tubing. 250 mL bottles take size 2 rubber stoppers; 500 mL bottles take size 4; 1,000 mL and 2,000 mL bottles take size 6;…