For connecting inert gas and vacuum sources Stopcock has metering groove cut into the plug to provide fine control of vacuum and inert gases. Distance between stopcocks is 65 mm for 8651N01 and 100 mm for 8651N03. Include patented pressure/vacuum retainers. Dimensions (mm): 8651N01: 230 L x…

Jacketed CHROMAFLEX® columns are provided with an acrylic water jacket to provide thermal control of temperature-sensitive chromatographic separations.  The acrylic jacket also acts as a safety shield.  Threaded Recommended sterilization is with ethylene oxide, 2N NaOH or…

Re-suspend protein and DNA pellets or grind soft tissues in micro centrifuge tubes Pestles can be hand operated or motor driven Autoclavable types available Ideal for cell and tissue culture preparation Choose the best pellet pestle for your applications RNase-, DNase- and Pyrogen-free …

Columns are supplied complete with glass barrel, 2 end fittings with 20 μm porosity HDPE bed supports, and screw caps Each column is also supplied with 5 feet (1.5 m) of FEP PTFE tubing (1/16” OD with 1.0 cm; 1/8” OD with 2.5 and 4.8 cm), 2 flangeless tubing nuts and 2 flangeless…

The Kuderna-Danish apparatus was developed in the laboratories of Julius Hyman and Company for the concentration of trace amounts of sample dissolved in organic solvents. The column is designed to speed evaporation with reduced hold-up. It is very useful in sample preparation before analysis with…

Has separate reflux overflow tube Graduated in 1/10 ml divisions from 0 to 1 mL; in 1/5 mL divisions from 1 to 10 mL With 24/40 joints; meets ASTM Standard E 123 Specialized for determination of water in emulsified asphalts With Standard Taper24/40 joints and reflux overflow…

Gravity chromatography column manufactured from medium wall tubing with 821000 PTFE stopcock Similar in design to the 420530 series 40-60 micron porosity glass frit at the lower end to act as a support for column packing material Replacement stopcock plug is 821001 Manufactured from 33…

Columns are supplied complete with glass barrel, 2 end fittings with 20 μm porosity HDPE bed supports, and screw caps Each column is also supplied with 5 feet (1.5 m) of FEP PTFE tubing (1/16” OD with 1.0 cm; 1/8” OD with 2.5 and 4.8 cm), 2 flangeless tubing nuts and 2 flangeless…

All-glass construction with ground tube Ideal for connective tissues Clearance between pestles and tubes is .004 to .006 inches* Pestle can be motor driven (see Thomas number 3411E25 for Drive Unit) Available in working capacities of 1, 5, 8, 17 and 45 mL . * Stated clearances…

Flow adapters Flow adapters can significantly improve FLEX-COLUMN® performance by protecting the gel bed from disruption during sample loading and by eliminating any dead volume above the gel bed.  Ideal for concentration and pH gradients, reverse flow separations and gravity…

Similar to 3432N01 series, but with PTFE pestle and an unground glass tube Ideal for soft tissue such as brain or liver Clearance between pestles and tubes is .004 to .006 inches* Pestle can be motor driven (see Thomas number 3411E25 for Drive Unit). Available in working…

Three-prong extension clamps hold objects ranging from 0.80 to 89 mm securely and safely. Two separate adjustment screws ensure even, precise pressure on glass to minimize the chance of breakage Clamp is easily adjusted to vary holding angle and distance from the stand Jaws are coated…

Produces a relatively coarse homogenate For cellular work where the nucleus remains intact after homogenization All glass construction * Stated clearances for the tubes and pestles are “total” not “annular”.

Snyder distillation column with floating ball valves for improved vapor-liquid contact. Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements.

A convenient stainless steel universal joint with 5/16 inch OD shaft and polyacetal adapter connects stirrer shafts to stirrer motors. Flexible design allows connection even if alignment is not precise. Stirrer Adapter, Flex-Shaft. For 8-10 mm Shafts

Economy Three Hole Cap Systems Economical way to helium sparge and deliver mobile phases Cap body is manufactured from PTFE and is supplied with a TFE/propylene O-ring and a polypropylene screw collar. The connecting threads on the top of the cap use standard 1/4-28 flangeless fittings. Two of…

Made of autoclavable CTFE/Stainless Steel Optional cordless drive unit available, see Thomas number 3411E25.

Tightly wound coil provides enough surface area to condense high vapor pressure solvents like hexane. With an internal, coil-type cold finger Standard Taper outer joint at the top, Standard Taper inner drip joint at the bottom 283000 does not have a drip joint Two hose connectors…

A general purpose column for analytical separations A plug of glass wool can be used to support the column packing PTFE stopcock plugs, 821001-0002 and 821001-0004, control the flow rate Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I…

For gravimetric oil and grease Three position linear system Heating mantle, controller and splash guard are required for complete system (clamps and support included): power 15 amps - 115 volts. Refrigerating circulator recommended for system water coolant: -4°C. Proper ventilation…

With Standard Taper Joints Complete with Allihn condenser with joint at bottom, Soxhlet extraction tube with top and bottom joint and flat-bottom flask Available in small, medium and large capacities Small Extractor with 125 mL flask (4406E10, E16, E22) Extraction chamber 30 mm i.d. x 95…

Used for dispensing a fixed volume of liquid into vessels with small openings. 675300 polyacetal Standard Taper clamp (one included) secures flask and head All-glass apparatus manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type…

Combines both conical and cylindrical surfaces to effectively reduce tissue and produce a uniform homogenate Ideal for connective tissue, such as muscle, heart and lung Clearance between pestles and tubes is 0.004 to 0.006 inches* Pestle can be motor driven (see Thomas number…

Bent angle of 105°, with Standard Taper joints on inlet and outlet ends and inner drip-tip which bypasses vacuum take-off tubulation Has drip-tip at exit end Side-arm accepts 5/16” i.d. flexible tubing Made from Kimax® Brand KG-33 borosilicate glass, which features a low coefficient of…

Gravity chromatography column manufactured from medium wall tubing with PTFE stopcock and in-line reservoir for containing liquid buffer Standard Taper joint size 24/40 These gravity columns may be used alone or in combination with 420575-2440 flow control adapter A coarse porosity glass…

Selected to give the best fit to Pellet Pestles, Thomas 3411D75 series Constructed of autoclavable polypropylene Available in blue or natural color

This apparatus combines two analytical techniques, Soxhlet extraction and Dean-Stark azeotropic distillation, into a single process for the removal of water, chlorinated dibenzo-p-dioxins (CCDs) and chlorinated dibenzofurans (CDFs) from wet particulate samples. Determination of water and…

Columns are supplied complete with glass barrel, 2 end fittings with 20 μm porosity HDPE bed supports, and screw caps Each column is also supplied with 5 feet (1.5 m) of FEP PTFE tubing (1/16” OD with 1.0 cm; 1/8” OD with 2.5 and 4.8 cm), 2 flangeless tubing nuts and 2 flangeless…

This three-position linear solvent recovery system is intended for use with Kuderna Danish evaporative concentrators. Heating mantle, controller, splash guard, clamps and supports provided with the complete system Power: 15 amps – 120 volts Refrigerating circulator recommended…