Grease-Free PTFE stirrer bearing designed for use under moderate vacuum applications. The bearing consists of a threaded glass adapter having an inner joint, a set of PTFE washer style bearings, a stainless steel spring, nylon alignment ring and Celcon® compression cap. The unique design of…

Support Stand was designed to accommodate vessels up to 10" diameter, to sit close to the support rod. Support rod is ideal for mounting stirring motors. Each of the four corners rests on a rubber cushion. The powder coated steel base measures 7.875” (200mm) W x 12.5" (316mm) deep…

10mm O.D. shaft is constructed using a molding process whereas the blade is molded directly onto the PTFE coated stainless steel shaft. This makes the stirrer chemically inert, easy to clean and can be used up to 280°C. The top of the shaft has 50mm of exposed 1/4" diameter stainless steel…

Cup is designed to catch all flaking that occurs with PTFE stirrer bearings. Made entirely of PTFE, the complete item consists of a compression fitting, deep perforated PTFE cup and a 50 micron porosity PTFE filter disc.

Shaft is precision ground and polished to fit our CG-2076 and CG-2077 10mm PTFE bearings. Designed to be used with cylindrical type reactors. The straight glass blades are spaced 90° apart and angled 15°.  PLEASE NOTE: STIRRER SHAFTS ARE DESIGNED FOR COUNTER-CLOCKWISE ROTATION.

Assembly consists of a 10mm OD Chem-Stir™ stirrer shaft, a precision bore-bearing having a standard taper inner joint and a PTFE blade. The blade is sized to fit the listed flask capacities.

Shaft is precision ground and polished to fit our CG-2086 19mm PTFE bearings. Designed to be used with cylindrical type reactors. The curved glass blades are spaced 120° apart and angled upward. PLEASE NOTE: STIRRER SHAFTS ARE DESIGNED FOR COUNTER-CLOCKWISE ROTATION. ALSO NOTE: 19MM…

AGITATORS, PTFE, 5.5IN OD, 90°, 19MM SHAFTS Agitator made entirely of PTFE and glass filled PTFE, provides excellent stirring at the bottom of filter reactors, especially when heavy slurries are being mixed. Agitator attaches to stir shaft by both a compression fitting and a glass filled…

A 19mm OD precision ground stirrer shaft to fit CG-2082 and CG-2083 19mm bearings. Side button for attachment of CG-2089 PTFE stirrer blades. PLEASE NOTE: THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF PTFE BEARING. FOR POLISHED SHAFTS USED WITH PTFE BEARINGS SEE CG-2088. ALSO NOTE: 19MM…

A 10mm precision ground and polished stirrer shaft for use with PTFE bearings and CG-2091 and CG-2092 PTFE agitators. Flat ground section extends half way up shaft and permits positive seating of the PTFE locking screws.

A 10mm precision ground stirrer shaft to fit CG-2070 through CG-2072 10mm bearings. Side button for attachment of CG-2080 or CG-2081 PTFE stirrer blades. PLEASE NOTE: THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF PTFE BEARING.  FOR POLISHED SHAFTS USED WITH PTFE BEARINGS SEE CG-2079.

Agitators are made entirely of PTFE and glass filled PTFE and are for use with 19mm or 25.4mm OD stirrer shaft CG-2097 and are available in 45°, 60° and 90° impeller angles. The 45° and 60° impellers are set up to stir downwards in a clockwise direction and upwards when rotated…

Agitator blades are constructed of PTFE with a glass filled PTFE locking nut. This enables them to be attached to the shaft in any vertical position. Note: Designed for use with CG-2079-X, CG-2078-X or CG-2096-X PTFE Covered stainless steel type shafts

Stirrer blade made of 1/8" thick solid PTFE for use with both Chem-Stir™ and button style stirring shafts having a 10mm OD.

Beaded pipe to sanitary fitting adapter connects to the 1-1/2” beaded pipe side arm of CG-1968-GL zero dead space drain valve. Approximate overall length of adapter is 1.75”.  NOTE: Requires a CG-1968 beaded pipe coupling.

Grease-Free PTFE stirrer bearing designed for use under moderate vacuum applications. The bearing consists of a threaded glass adapter having an inner joint, a set of PTFE washer style bearings, a stainless steel spring, nylon alignment ring and Celcon® compression cap. The unique design of…

Semi-micro stirrer has a 10mm OD x 440mm long precision ground button style shaft and a 15 x 46mm TFE blade. Lower end of shaft has a reduced diameter to allow passage through a 19/22 outer joint. The 15 x 46mm blade can be used in flasks having a capacity of 100mL and above. Complete stirrer…

Similar to CG-2070 but with a tooled lubricant cup at the top of the bearing to hold an increased amount of lubricant. NOTE: Not for use with CG-2078 or CG-2079 polished stirrer shafts.

Similar to CG-2070, but water jacketed to control bearing temperature. For use in moderate vacuum with a CG-2074 or CG-2075 ground 10mm stirrer shaft. NOTE: Not for use with CG-2078 or CG-2079 polished stirrer shafts.

A 10mm OD precision ground and polished stirrer shaft with our patented** Chem-Stir™ blade attachment system. Shaft (C) has been manufactured with a ring at the lower end to permit attachment of the blade (B) with a PTFE nut (D) and bolt (A). Shaft is supplied complete with PTFE nut and bolt…

Heavy duty PTFE anchor made of 0.500” thick PTFE. Blade is shaped to mirror the contour of Chemglass cylindrical reactors. Designed for use with CG-2078 Chem-Stir® 10mm stirrer shaft. The blade is secured to the stirrer via a PTFE pin.  PLEASE NOTE: CG-2081-A-02 IS NOT…

Replacement components for CLS-1414 and CLS-1415 Spinner Flasks.The Complete Impeller Assembly consists of top cap, silicone liner, glass rod, compression fitting magnet holder, paddle and magnetic stir bar.

Precision bore bearing for use in moderate vacuum with a CG-2074 or CG-2075 ground 10mm stirrer shaft. NOTE: Not for use with CG-2078 or CG-2079 polished stirrer shafts.

Grease-Free PTFE stirrer bearing designed for use in moderate vacuum applications. Bearing consists of a threaded glass adapter having the listed inner joint, a saddle o-ring, a body bushing with a compression and locking nut, and a precision PTFE inner bearing. The saddle o-ring provides only…

This lightweight micro stirrer is ideal for use with tissue grinders having stainless steel pestles. Supplied complete with a stirrer/controller, tripod with a vertical support rod, clamp holder and a coupling to fit the 6.35mm diameter of the stainless steel pestle rod.

Blade is shaped to resemble the contour of a round bottom flask. Blades are available solid or perforated. Made of 1/8" PTFE to fit 10mm OD stirrer shafts. Minimum joint size listed is the size required to allow passage of the blade.

PTFE stirrer bearing with a hose connection for vacuum or inert gas source on a single neck flask. Grease-free design has only glass and PTFE in contact with the reaction, and can be used under moderate vacuum applications. Bearing consists of a threaded glass adapter having the listed inner joint…

16mm O.D. shaft is constructed using a molding process whereas the blade is molded directly onto the PTFE coated stainless steel shaft. This makes the stirrer chemically inert, easy to clean and can be used up to 280°C. The top of the shaft has 50mm of exposed 1/2" diameter stainless steel…

FLAKE-FREE Chemically Resistant Maximum 500 RPM; Vacuum (~5 Torr) and Pressure (~3 PSI) Polymer Blend Sleeve Provides Excellent Wear Resistance For Use with Polished Glass, PTFE or Stainless Steel Stirrer Shafts Universal Chem-Vac™ PTFE stirrer bearing provides a VACUUM TIGHT…

Precision ground and polished stirrer shaft for use with Chemglass process reactors. Designed to utilize CG-2095 and CG-2096 PTFE agitators. Lower portion of stirrer shaft is sandblasted and has a 3/8” wide flat.  Please Note: CG-2097-75 and CG-2097-100 are made from heavy wall tubing…

Agitators are made entirely of PTFE and glass filled PTFE and are for use with 10mm OD stirrer shaft CG-2075-B. Great for use a & "foam breaker" at the liquid level in the reactor. Agitator hub is open so that it can be positioned anywhere along the stirrer shaft.

Agitators are made entirely of PTFE and glass filled PTFE and are for use with 10mm OD stirrer shaft CG-2075-B. Available in 45°, 60° and 90° impeller angles. The 45° and 60° impellers are set up to stir downwards in a clockwise direction and upwards when rotated…