Chemglass Lab Flasks
-
Replacement Parts For Internal Impeller Assembly Bioprocess Spinner Flasks
-
Quadruple baffled Erlenmeyer flasks are sterile, non-pyrogenic and manufactured with polycarbonate resin. Flasks are supplied with either exclusive DuoCap® designed for both aerobic and anaerobic applications (for aerobic applications the cap utilizes a 0.22µm pore size PTFE membrane for…
-
Non-baffled flasks are ideal for growing, mixing and storing both aerobic and anaerobic cultures. Graduated to approximate volumes. Delong style neck is made to fit stainless steel or plastic closures, while reducing the amount of splashing that would reach the closure.
-
Heavy Wall Blank Filter Flasks
ChemglassExtra heavy, unmarked blanks for fabrication of filter apparatus. Top has a tooled finish to accept a rubber stopper or neoprene filter adapter.
-
Evaporating flask for use with rotary evaporators. Flasks have a HEAVY WALL for vacuum applications and are balanced to prevent run-out during rotation. For Plastic Coated flasks, see CG-1512-P.
-
Flask has 4 bottom baffles and a constriction just below the neck to prevent splashing from reaching the closure.
-
Spinner Flask
ChemglassWater jacketed, flat bottomed spinner flasks consist of a water jacketed spinner flask, manufactured from Type 1 Class A borosilicate glass. Flasks are typically used with a circulating water bath. Jacket volumes are approximate and flasks are not graduated. Note: Paddle and Cap assembly are…
-
2800mL flasks are designed for culturing organisms that require a large surface area to volume ratio. Available with 70mm screw neck with a solid or vented cap.
-
2800mL flask with 3 baffles on the lower outside edge of the flask to help oxygen transfer to the culture medium.
-
Similar to CG-1600 but with the addition of a mixing bulb between the calibration line and the stopper. The mixing bulb contains approximately one tenth of the flask capacity and aids in the mixing or dissolving of the flask contents. Supplied complete with one solid glass pennyhead stopper. For…
-
Flasks, Dewar, Low Form, Foam
ChemglassFeatures: Increased SAFETY- Unbreakable Lightweight Design Each Dewar is Supplied with a Lid Patented Closed Cell Foam Construction (USPTO # 7,971,744) Lower Boil Off and Consumption of Liquid Nitrogen Patented foam dewars provide a safe and durable vessel for handling…
-
Round bottom 2-neck flask having standard taper outer joints, both being of the same size. Available with a choice of a 2mm high vacuum glass stopcock having a S.S. constant pressure retaining device or a 0-4mm Chem-Cap® Airfree® inlet valve. Side neck can be fitted with a CG-3022 septum…
-
Lower half of flask has a jacket permitting heating or cooling of the contents with fluid from a constant temperature bath. The unique design of the Chem-Drain valve incorporates a PTFE plunger that allows the contents of the flask to drain directly through the bore of the plunger. When closed,…
-
Round bottom, HEAVY WALL, three-neck flask with standard taper outer joints on the center neck and vertical side necks. Lower half of the flask is jacketed with two hose connections for circulation of heating or cooling liquid.
-
Wide mouth design facilitates mixing, pipette access, sampling and filling. Unique Flat Bottom Interior permits the use of a standard stir bar. Large permanent white letters make the capacity clearly visible. Flasks are calibrated "To Contain" at Class A tolerances, per ASTM E288…
-
Replacement vessel is supplied with black phenolic, rubber lined caps for the 18mm side arms, polypropylene caps and pouring rings for the GL-32 and GL-45 side arms.
-
FLASKS, FERNBACH, 2800ML, WITH 6 BAFFLES, 2800mL flask with 3 baffles on the lower outside edge of the flask and 3 baffles on the bottom surface of the flask to help oxygen transfer to the culture medium. FLASKS, SHAKE, NO BAFFLES, DELONG NECK, WITH STAINLESS STEEL CLOSURES, Non-baffled flasks…
-
Heavy Wall blanks are 30% heavier than our standard CG-618 series. Blanks are used in the fabrication of single or multi-neck round bottom flasks. NOTE: NECK IS UNFINISHED, FLASK CANNOT BE USED WITHOUT MODIFICATION OF NECK.
-
-
Flasks, Micro Volumetric, Class A
ChemglassClass "A" micro volumetric flask calibrated to contain. With 14/20 top outer joint and supplied complete with a CG-3000 14/20 hollow stopper. Flasks have hex base for stability and a V shaped interior bottom for total sample retrieval.
-
3 Baffles Vented Cap Shake Flasks
ChemglassFlask has 3 baffles on the lower outside edge of the flask to maximize oxygen transfer to the culture medium when used on an orbital shaker. The polypropylene vented caps have a 0.22µm (PTFE) hydrophobic membrane to allow sterile gas exchange while preventing contamination. Since these caps…
-
Round bottom, HEAVY WALL single short neck flask for use on rotary evaporators for receiving distillate. Joint at the top of the flask is a 35/25 socket. Plastic Coated to prevent injury from broken glass while preventing spillage of hazardous materials.
-
Flasks, PFA, Round Bottom, Three Neck
ChemglassAll PFA three neck round bottom flask with standard taper outer joint center neck and two additional 20° angled side necks. Allows assembly with a temperature probe, electrode or tube. Flask can withstand MAX temperature of 250°C and a MIN temperature of -200°C.
-
Round bottom, HEAVY WALL single short neck flask with a standard taper outer joint. The 29/26 flasks have a groove tooled just below the grind to aid in clamping of the flask. Please note: There are separate listings for different capacity single neck round bottom flasks.
-
Round bottom, HEAVY WALL, five-neck flask with standard taper outer joints on the center neck and vertical side necks.
-
Single Neck Flat Bottom Flasks
ChemglassSingle neck, flat bottom flask with a standard taper outer joint.
-
Manufactured from borosilicate glass these wine testing volumetric flasks have wide bases and a flat bottoms for stability. Flask neck is graduated in 1mL subdivisions from 680 to 780mL. The long neck is calibrated To Contain at 20°C and markings indicate the volume of liquid when filled to…
-
Round bottom, HEAVY WALL single short neck flask with a standard taper outer joint. The 29/26 flasks have a groove tooled just below the grind to aid in clamping of the flask. Please note: There are separate listings for different capacity single neck round bottom flasks.
-
Flat bottom borosilicate flask for use with Labconco and Virtis freeze dryers. Wide mouth design provides easy access sample. PLEASE NOTE: FLASKS ONLY. NOT SUPPLIED WITH RUBBER TOP, FILTER OR O-RING. Note: Labconco and Virtis are not related to or affiliated with Chemglass, and…
-
Round bottom, HEAVY WALL flask with standard taper outer joint. Side tubulation accepts a CG-1040 rubber fitment for insertion of thermometers or bleed tubes. Supplied complete with one CG-1040 rubber fitting.
-
Extra deep baffle indents on the lower outside edge of the flask to maximize oxygen transfer to the culture medium when used on an orbital shaker.