Ace Glass
-
Viscometer, Modified Ubbelohde
Ace GlassUsed in ASTM Method D 1601. A test for Dilute Solution Viscosity of Ethylene Polymers at 130 degree C. It is applicable to a reasonably wide spectrum of ethylene polymers having densities from 0.913 to 0.970g/cc. Available in capillary sizes .6, .7, and .8mm.
-
Head, Reaction Flask, 100MM, 4 Neck
Ace GlassReaction flask head, 100mm (4 inch) conical flange, four neck. Center neck in-line with two 24/40 side necks. Third side neck is perpendicular to the in-line necks. Use our 6496 series clamp to secure to flask.
-
Reaction Flask, Cylindrical, Jacketed
Ace GlassCylindrical jackted reaction flask with a 4" (10.2cm), top opening. Jacket inlet/outlets are available with tangentially sealed with 28/15 O-Ring ball joint connections, or with #11 Ace-Threds, for use with 3/8in tubing.
-
Stirring Shaft, Unground, 9mm
Ace GlassUnground, 9mm OD stirring shaft design for use with our 9528 vacuum and debris free stirrer assembly. 380mm straight section, 416mm overall length. Use our 9530-08 blade.
-
Column has standard taper 24/40 joint at top and 2 mm bore stopcock at the bottom with Por. B (70-100m) fritted disc sealed into the bottom of tube.
-
With standard taper 24/40 joint and outlet tube bent at 75 degree angle.
-
Tube, Gas Dispersion
Ace GlassFritted disc is angled approximately 15 degree from stem, which permits the small gas bubbles to rise from the disc surface without excessive formation of large bubbles. These tubes give a performance compared to a horizontal disc, but the method of co
-
Adapter, Septum Inlet, Single Port
Ace GlassSampling adapter with joint at bottom and septum port at top for handling air-sensitive materials. Supplied with septum.
-
Reaction Flask Head, #7 Ace-Thred
Ace GlassHeads with four necks, three inline standard taper joints and one perpendicular #7 Ace-Thred™ thermometer joint. Included 5029 nylon bushing & FETFE o-ring permits vertical adjustment of 6-7mm OD thermometers. Use with our 6504,6511 & 6516 reaction vessels that feature either a 137 x 100mm ID…
-
-
Drying Assembly, with Aluminum Holder
Ace GlassOriginally used for Lyophilizing and storing frozen slices of tissue for quantitative histochemistry (see O.H. Lowry, Journal of Histochem. & Cytochem., I, 420, 1953). More recently, used as a vacuum tube with aluminum holders by Nelson & Wakefield, Journal of Neuropathology & Exper. Neurology,…
-
Bottle, Gas Washing
Ace GlassGas washing bottle, 270mL with inner coil. Used with 6550 Cyanide distillation apparatus.
-
Immersion Well, Photochemical, Plain
Ace GlassQuartz immersion well, triple-walled, unjointed (plain) for use in our 6962,7863,7864,7865 & 7891 series reactor bodies. Designed for low temperature reactions cooled up to -78 degrees C. The outer two walls are permanently sealed and evacuated. The inner removable tube set consists of one each…
-
Complete reaction assembly for sample volumes from 250ml to 1800ml. Included are three glass reactors [9837-20,9833-12,9833-16], power supply with converter [9810-24], 3/4in horn [9814-27], 3/4in extender [9816-08], (3) bushings [7506-12] and clamp ([9825-21].
-
Rugged cylindrical jacketed reaction flask with Duran, flat, ground flange and o-ring groove. Various bottom outlet options are available (see details below). For use with 6517 quick release clamp. Jacket inlet/outlets are available with either tangentially sealed o-ring ball joints or with…
-
Distillation Head, Vacuum Type
Ace GlassVacuum distillation head featuring glass or PTFE stopcock plugs which allow the receiver to be removed from the head without disturbing the refluxing solvent. All joints are 24/40 with the exception of a 10/18 thermometer joint which will accept our 5028-24 adapter and 6.4mm thermometers such as…
-
Dry Ice Trap, Twin
Ace GlassTwin chambered dry ice condenser-trap similar to 8748 except dry ice finger condensers in this unit are NOT removable. Ports at top for connecting to Rotary Evaporator and to vacuum source are 3/8" O.D. Condensate stopcock at bottom is 4mm PTFE, 90 degree bore, that allows draining each chamber…
-
Jacketed reaction flask with round bottom. Flat flange is grooved for using an o-ring (instead of a flat gasket) to seal to a head. Jacketed for temperature control of ingredients. Supplied with CAPFE o-ring. Codes -01 thru -04 have 28/15 o-ring ball joints on inlet/outlet. Codes -301 thru -304…
-
Still, Solvent Recovery
Ace GlassWhen attached to the top of Snyder Column, unit is designed to recover solvent normally lost during Kuderna-Danish Evaporative Concentrations. PTFE stopcock (1:5, 2mm bore) provides option for total reflux or takeoff. #7 Ace-Thred on side arm accepts tubing 6 - 7mm O.D. 5029-10 Nylon bushing and…
-
Caps, GL Thread - Duran®
Ace GlassScrew caps and pouring rings for use with GL threaded bottles. For steam autoclaving, we recommend PBT (polybutylene theraphthalate) caps with a PTFE liner, -45 to 180 degrees C rated. Polypropylene is only rated to 140 degrees C. 316L stainless steel cap is for use with stainless steel laboratory…
-
Funnel, Addition, Graduated
Ace GlassGraduated addition funnel featuring standard taper joints,graduations in both ascending and descending volume,protected drip tip and a glass stopcock. Graduations are calibrated from the stopcock.
-
Double-jacketed, with standard taper 24/40 inner and outer joint at bottom and top. Extra cooling capacity for volatile materials. Compact design retards diffusion. With #7 Ace-Thred and Ace-Safe PTFE hose connections on inlet and outlet with barb for
-
Condenser, Liebig
Ace GlassWith 110mm jacket length, also an additional vacuum takeoff between outer joint and jacket.
-
Nephelo Flask, Baffled, Long, Plain Neck
Ace GlassTriple baffled, Nephelometer, culture flask with three outside bottom baffles. Side cuvette arm fits standard Nephelometers and specrophotometers. The side baffles promote better mixing and oxygen transfer. The 25mm long style neck accomodates either plastic or stainless steel closures, see Ace…
-
Tube, Straight
Ace GlassFor construction of special apparatus. All porosities of a given size are priced the same.
-
Flask, Reaction, Cylindrical
Ace GlassCylindrical, heavy wall reaction flask with extra thick flat, ground flange. Without constriction at top to facilitate introduction/removal of material and allow for ease of cleaning. Available in 1L to 4L capacities, flat bottom and round bottom, with
-
Ready Reactor™, Kilo-Scale
Ace GlassPre-packaged, turnkey 20 liter and 50 liter reaction systems for research and production purposes. Systems feature jacketed vessels, multi-neck flask heads, Universal support stand, and either a rod mounted brushless DC stir motor in our 20 liter (IKA Eurostar 60 Control) or a flange mounted 3/8 hp…
-
Adapter, Straight Connecting
Ace GlassStraight connecting adapter with inner or socket top and outer or ball bottom.
-
Filter Reactor, Plain
Ace GlassComplete filter reactor assembly allows single or multi-step reactions and filtrations in the same vessel. Features heavy wall glass, interchangeable filters, mechanical agitation and 4" or 6" Duran flanges. Available capacities from 150ml to 6000ml. P
-
Joints, Inner Member, Microscale
Ace GlassStandard taper inner ground joints used in fabrication of ACE Microscale Glassware. Use with 7609 outer member. Codes -11, -12 and -13 have drip tip.
-
Pressure Tubes, Sample Port
Ace GlassAce Glass pressure tubes are the premier glass pressure tubes in the world, rated at 150 psig at 120 degrees C. Featuring a #7 Ace-Thred sample port, these tubes offer the convenience of sampling while remaining connected to the researcher's apparatus. Due to varying conditions, Ace cannot…
-
Adapter, 15mm o-ring joint to standard taper or ball joints with o-ring seals. Fetfe o-rings for both joints are supplied.