Kemtech America, Glass
-
Synthware rotary evporator anti-splash trap, modified. With extra coarse porosity fritted disc sealed above lower inner joint. Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. Frit reduces foam overflow from being…
-
Synthware Inlet Adapters with Extended Length Lower Tubes
Kemtech AmericaSynthware inlet adapter with extended length lower tube. Allows for the introduction of reactants below the interior surface. Tube extends 153mm (6 inches) below the joint. Tubing has the same O.D. on both ends of the joint.
-
Synthware Vacuum Take-Off Adapters with PTFE Stopcocks
Kemtech AmericaSynthware vacuum adapter with 2mm straight bore PTFE stopcock on the hose connection.The upper outer and lower inner standard taper joints are the same size.
-
Synthware Vacuum Distilling Adapters
Kemtech AmericaWith two standard taper inner joints that are parallel and at a 75 degree angle to the connecting tube. Distance between joints is 100mm.
-
SYNTHWARE Short Path Distilling Head for Volatile Solvents
Kemtech AmericaWith the condenser being a combination of a cold coil and Leibig. Top outer joint is a 10/18 for use with a 50mm immersion thermometer. For best result, use D272440.
-
Synthware Distilling Adapters, 75°
Kemtech AmericaSynthware distilling adapter with top compression cap. With same size standard taper inner joints on bottom and side arm. Cap accomodates 5.0 - 7.5mm O.D. thermometer. Supplied with one Nylon cap and one Viton o-ring.
-
Synthware Rotary Evaporator Anti-Splash Traps
Kemtech AmericaTrap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With upper outer and lower inner standard taper joints.
-
SYNTHWARE Solvent Still Head, Repurification
Kemtech AmericaSolvent Still Head, Repurification Joint: 24/40
-
SYNTHWARE Dessicant Flask
Kemtech AmericaDessicant Flask, Joint: 34/45, with 2mm bore PTFE stopcock.
-
Synthware Distillation Adapters with Threaded Thermometer Ports
Kemtech AmericaSynthware distillation adapter with threaded thermometer port. The threaded port will accommodate a 6-7.5mm O.D. plain thermometer. The adapter has standard taper top outer joint and inner joints for the bottom and side. All joints are the same size.
-
SYNTHWARE Claisen Adapter
Kemtech AmericaClaisen Adapter, Microscale, Synthware, Joints: 14/10, supplied with two compression caps, two Viton O-rings and two PTFE-faced silicone septum.
-
Synthware Distillation Adapters, Vigreux
Kemtech AmericaSynthware Vigreux distillation connecting adapter. Indenstations in lower section improve liquid/vapor contact. The standard taper top outer joint accomodates a 76mm immersion thermometer. Bottom and side joints are standard taper inner joints.
-
SYNTHWARE Hickman Still Head, with Side Port
Kemtech AmericaHickman Still Head, with Side Port, Synthware, Joint: 14/10, for microscale fractional distillation, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.
-
SYNTHWARE Graduated Distilling Cow Receiver
Kemtech AmericaTubes are graduated from 0-3mL in 0.2mL subdivisions.
-
Synthware Rotary Evaporator Traps
Kemtech AmericaSynthware rotary evaporator trap. Anti-climb design. Trap provides expanded volume for reactions that have a tendency to foam excessively. The inner vapor tube is sealed to the top of the trap to prevent entry into the condenser.
-
Synthware Distillation Adapters
Kemtech AmericaSynthware distillation adapter with a 10/18 standard taper outer joint for a 76mm immersion thermometer. The adapter has a standard taper top outer joint and inner joints for the bottom and side.
-
-
Synthware Distilling Adapters, 105°
Kemtech AmericaSynthware distillation adapter with sealed in drip tip. Adapter is bent at 105 degrees. Standard taper top outer joint and lower inner joints.
-
SYNTHWARE Gas Inlet/Outlet Adapter
Kemtech AmericaGas Inlet/Outlet Adapter, Microscale, Synthware, Joint: 14/10, Hose Connection OD: 8mm.
-
SYNTHWARE PTFE Joint Sleeves
Kemtech AmericaJoint Sleeve, PTFE, Ribbed with gripping ring, Synthware, Sizes available to fit various joint sizes.
-
Synthware Inlet Adapters with Hose Connection
Kemtech AmericaAdapter has a Nylon compression cap and a Viton o-ring to form a vacuum tight seal. Cap accommodates 5.0 - 7.5mm O.D. thermometer or gas inlet tube. The 8mm hose connection can be used for N2/Ar introduction or vacuum. Supplied with one Nylon cap and one Viton o-ring.
-
Synthware Vacuum Adapters with Outer Joints & Glass Stopcocks
Kemtech AmericaSynthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper outer joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.
-
SYNTHWARE Short Path Vaccum Jacketed Distillation Apparatus
Kemtech AmericaUsed with 25mm immersion thermometer, and D27 distillation receiver.
-
Synthware Vacuum Transfer Adapters
Kemtech AmericaSynthware vacuum transfer adapter with PTFE stopcocks and standard taper inner joint. Used for the transfer of sensitive and hazardous solutions while under vacuum.
-
SYNTHWARE Inlet Connecting Adapter
Kemtech AmericaInlet Connecting Adapter, High Vacuum Valve Joint: #15 O-ring Valve Size: 0-4mm Side Port: 10mm OD.
-
Synthware Distillation Adapters, 75°
Kemtech AmericaSynthware distillation adapter bent at 75 degrees. Both ends are standard taper inner joints and are the same size.
-
Synthware Rotary Evaporator Anti-Splash Traps, Modified
Kemtech AmericaTrap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With two 4mm drain holes at the base of the inner tube to allow solvent to drain back into the evaporation flask. Has upper outer and lower inner standard taper joints.
-
SYNTHWARE Solvent Still Head with Drainage Port
Kemtech AmericaSolvent Still Head Capacity: 500 and 1000mL available Top Joint: 24/40 Bottom Joint: 24/40 and 29/42 available Side Joint: 14/20 Drainage Port Joint: 14/20
-
SYNTHWARE Snyder Distillation Column
Kemtech AmericaSnyder Distillation Column, 3 Section Top Outer Joint: 24/40 Lower Inner Joint: 24/40 Column Height: 150mm Overall Height: 300mm For use with Kuderna-Danish flask.
-
SYNTHWARE Kugelrohr Distilling Bulbs
Kemtech AmericaKugelrohr Distilling Bulb Capacity: 5, 10, 15, 25 or 50mL available Joints: 14/20, Bulb O.D.: 25, 31, 35, 42 or 48mm available Overall Height: 80, 85, 90, 98 or 105mm available Used in distillation of very small amount of distillate at lower temperature with high efficiency.
-
Synthware Claisen Adapters, Modified
Kemtech AmericaIt is modified with an additional side arm at 45 degrees to the vertical outer joint. All joints are the same size.
-
Synthware Vacuum/Inert Gas Adapters
Kemtech AmericaAllows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. Hose connection is at a 90 degree angle to the standard taper inner joint.