Bellco Glass, General Lab Products
-
L Bubbler Tube 15L
Bellco GlassSparging accessory for vertical sidearm spinner flasks. Manufactured from 316l stainless steel with electropolish finish. Includes polypropylene cap with 1/4? white compression fitting and white silicone gasket. .040 inch hole for aeration of fermentation cultures where shear force is less critical.
-
IOB Impeller Assembly 15L
Bellco GlassStainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks. Cap size: 100mm Flask size: 15l Paddle: 9 1/2" x 6"
-
Large Flange Air Stone Sparger 15L
Bellco GlassLarge flange air stone sparger for large flange vessels. Fits through stainless steel head plate fitting. These spargers fit through a 5/16? fitting. 316 l stainless steel Ra 32 finish or better Acrodisc filter assembly, 0.2 micron
-
316 l stainless steel construction
-
Glass Micro-Carrier Impeller Shaft 15-36L
Bellco GlassManufactured from type 1 class a Borosilicate glass. For spinner flasks 3l to 36l Dimensions: 9mm x 500mm long
-
3-Port Harvest Assembly 8L
Bellco GlassMaterial: 316l SST with electropolish finish, ra 32 or better, inside & out Dimensions: harvest tube (3/8" od) - 1" above slug, 15" insertion length Addition tube (1/4"od) - 1" above slug, 2 21/64" below Vent tube (1/4" od) - 1" above slug, .975" below Supply with 45mm pp blue open top screw cap &…
-
Micro-Carrier Impeller Assembly 1-3L
Bellco GlassImpeller assembly for micro-carrier spinner flasks. Consist of magnet holder, silicone plug, magnet, and ptfe paddle. Impeller size: 1-3l Paddle dimensions: 1 3/4" x 4 1/4" Consist of: Magnet holder: a523-207 Silicone plug: a523-200 Magnet: 1975-0300a Ptfe paddle: a523-206
-
Stainless Steel 3-Port Assembly 1L
Bellco GlassSize: 1l Seam welded w/ electropolish finish 3-port w/ siphon, fill & vent tubes Includes: 45mm pp cap & silicone gasket
-
Bellco Heating Blanket 230V-500mL 50 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 500ml Watts: 50 Dimension (in.): 1 x 10.5 1 latch 6ft…
-
Stainless Steel Bent Harvesting Tube 15L 1/4"x20"
Bellco Glass316l stainless steel bent harvesting tube for 15l flat bottom omni vessel. Use with large flange head-plate. Size: 1/4" x 20" Id: 5/32"
-
3-Port Thermowell Assembly 36L
Bellco GlassThermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube. Port Thermowell assembly For low profile 3l vessel Material: 316l…
-
Stainless steel curved harvesting tube for 8l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 8l Dimensions: 1/2" x .430 x 20"
-
IOB Impeller Assembly 6L
Bellco GlassStainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks. Cap size: 100mm Flask size: 6l Paddle: 6 3/4" x 5" Overall length: 10 1/2"
-
Metal stone sparger 15l round bottom Metal stone sparger 15l for flat or round bottom omni vessels. Sparger inserts through stainless steel headplate fitting. 4 1/2?wide x 23 1/2? long 316 l stainless steel ra 32 finish or better Stainless steel frit
-
Bellco Heating Blanket 115V-8L 375 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 8l Watts: 375 Dimension (in.): 3 x 26.5 2 latches 6ft…
-
GL45 L-Bubble Tube w/ Holes 36L w/ (10) .040 Holes
Bellco GlassSparger for vertical sidearm spinner flasks. Includes polypropylene cap with 1/4? compression fitting and white silicone gasket. Material: 316l stainless steel with electropolish finish Ra 32 finish or better Includes polypropylene cap, 1/4" white compression fitting, white silicone gasket…
-
Metal Stone Sparger 15L For Flat Bottom Omni Vessels
Bellco GlassMetal stone sparger 15l for flat or round bottom omni vessels. Sparger inserts through stainless steel headplate fitting. 4 1/2?wide x 20 1/2? long 316 l stainless steel ra 32 finish or better Stainless steel frit
-
-
Stainless steel curved harvesting tube for 5l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 5l Dimensions: 1/2 x .430 x 14 1/4"
-
Round Bottom Marine Impeller 15L
Bellco GlassDimensions: 1/2? od x 12 1/2? long Stainless steel 4? od right hand pitch marine prop & e-clip Material: 316l stainless steel with electropolish finish For round bottom omni vessel (1964-88405) Need l/f head plate, over head drive motor
-
Silicone 2-Port Assembly 45mm
Bellco GlassIncludes 2 clear silicone tubes molded into the stopper with 6" on both sides of the slug Tubing is 3/16" id x 3/8" od.
-
-
Low Profile 3-Port Sparger w/ Holes 6L
Bellco Glass316-l stainless steel ra32 or better finish .040? drilled holes sparger for low profile vertical side arm vessels. Threaded end is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket. Triple tube configuration with vent, fill/sample and sparge.
-
2-port air stone stainless steel sparger assembly is designed for the sparging of gases into the vessel liquid media. This design allows access through the side arms with a screw on cap assembly. Fully autoclavable. Sparger assembly for 6l l/p over head drive vessel Fits thru a 45mm sidearm 316l…
-
Metal Stone Sparger 5L For Flat Bottom Omni Vessels
Bellco GlassMetal stone sparger 5l for flat or round bottom omni vessels. Sparger inserts through stainless steel headplate fitting. 4 1/2?wide x 12? long 316 l stainless steel ra 32 finish or better Stainless steel frit
-
-
Stainless steel curved harvesting tube for 36l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 36l Dimensions: 1/4" x 5/32 x 24"
-
Stainless Steel 3-Port Assembly 36L
Bellco GlassSize: 36l Seam welded w/ electropolish finish 3-port w/ siphon, fill & vent tubes Includes: 45mm pp cap & silicone gasket Dimensions: 1/4" x 5/32" Longest tube: 12 1/8" at bend
-
3-Port Sparger Assembly w/ Frit 8L
Bellco Glass316-l stainless steel ra32 or better finish 10 micron porosity stainless steel frit for low profile vertical side arm vessels. Frit is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket Triple tube configuration with vent, fill/sample and sparge.
-
IOB Impeller Assembly 500mL
Bellco GlassStainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks. Cap size: 100mm Flask size: 500ml Paddle: 2" x 2"
-
Sparger for vertical sidearm spinner flasks. Includes polypropylene cap with 1/4? compression fitting and white silicone gasket. Material: 316l stainless steel with electropolish finish Ra 32 finish or better Size: 21?
-
Valley Heating Blanket 115V-3L 150 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Watts: 150 Dimension (in.): 2"tall x 17.5 diameter 1 latch Caution:…