Media addition bottle 2l

Paddle dimensions: 1 1/2" x 3 3/8"

Manufactured from 316l stainless steel. Impeller assembly for micro-carrier spinner flasks. 1965 series micro-carrier spinner flask Size: 250ml

Stainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks. Cap size: 100mm Flask size: 15l Paddle: 9 1/2" x 6"

Glass ball houses a magnet for gentle agitation of micro-carrier beads and has a 70mm cap. Specially formed bottom indent prevents accumulation under the impeller. Cap size: 100mm Size: 6-8l

Glass ball houses a magnet for gentle agitation of micro-carrier beads and has a 70mm cap. Specially formed bottom indent prevents accumulation under the impeller Cap size: 70mm Size: 100ml

316-l stainless steel ra32 or better finish .040? drilled holes sparger for low profile vertical side arm vessels. Threaded end is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket. Triple tube configuration with vent, fill/sample and sparge.

Heavy walled construction for cell culture and fermentation applications. Heavy duty o-ring flange creates positive seal for stainless steel head-plate. For use with stainless steel head-plate, o-ring, and locking clamp. Use with CellTrol ii only single or dual systems, and speed control modules.

Thermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube. Port Thermowell assembly For low profile 3l vessel Material: 316l…

Impeller assembly for micro-carrier spinner flasks. Consist of magnet holder, silicone plug, magnet, and ptfe paddle. Impeller size: 15-36l Paddle dimensions: 3"x 10"

Stainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks Cap size: 70mm Flask size: 500ml Paddle: 2" x 2"

316-l stainless steel ra32 or better finish .040? drilled holes sparger for low profile vertical side arm vessels. Threaded end is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket. Triple tube configuration with vent, fill/sample and sparge.

The stainless steel 100mm iob probe cap seal is manufactured from 316l stainless steel and has a red-silicone sealing gasket with a 100mm blue polypropylene screw cap. The stainless steel probe cap seal has four accessory ports surrounding a centrally located internal impeller assembly. Two of…

Heavy walled construction for cell culture and fermentation applications. Heavy duty o-ring flange creates positive seal for stainless steel head-plate. For use with stainless steel head-plate, o-ring, and locking clamp.

Manufactured from 316l stainless steel with electropolish finish. Ra 32 finish or better inside and out. Ideal use for cell culture and reduces shear in delicate cell culture. Blade dimension: 5 3/4 x 2? Shaft oal: 14 1/2? Constructed of 316l electropolished stainless steel Marine impeller includes…

Stainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks. Cap size: 100mm Flask size: 8l Paddle: 6 3/4" x 5"

Dimensions: 1/2? od x 7 1/2? long Stainless steel 4? od right hand pitch marine prop & e-clip Material: 316l stainless steel with electropolish finish For round bottom omni vessel (1964-88405) Need l/f head plate, over head drive motor

Metal stone sparger 5l for flat or round bottom omni vessels. Sparger inserts through stainless steel headplate fitting. 4 1/2?wide x 14? long 316 l stainless steel ra 32 finish or better Stainless steel frit

Ideal use for pestle glass and stirrer rods. Used with homogenizer drive. Size: 10mm

Bellco compression fittings are designed using our standard 45mm blue polypropylene open top caps and white silicone gaskets. A wide variety of fittings are available to allow ph and do monitoring via insertion of these probes into sidearms or vessels. Bellco probe adapters are designed to allow…

Gently introduces bubbles into vessels. Includes 45mm polypropylene cap and white silicone gasket. 316l stainless steel 20 ra finish Size: 36l 12mm od coarse glass frit 0.2um Acrodisc filter w/ hose fitting

Material: 316l stainless steel with ra finish of 32 inch or better, inside and out Dimensions: odxid:1/4? x 5/32? x 4.0? long

Manufactured from type 1 class a Borosilicate glass.

Heavy walled construction for cell culture and fermentation applications. Heavy duty o-ring flange creates positive seal for stainless steel head-plate. For use with stainless steel head-plate, o-ring, and locking clamp. Use with CellTrol ii only single or dual systems, and speed control modules.

Size: 500ml Seam welded w/ electropolish finish 3-port w/ siphon, fill & vent tubes Includes: 45mm pp cap & silicone gasket Dimensions: 1/4? x 5/32? Longest tube: 2 5/8? at bend Neck: 70mm

Material: 316l SST with electropolish finish, ra 32 or better, inside & out Dimensions: harvest tube (3/8" od) - 1" above slug, 8 3/8" insertion length Addition tube (1/4"od) - 1" above slug, 2 21/64" below Vent tube (1/4" od) - 1" above slug, .975" below Supply with 45mm pp blue open top screw cap…

Polypropylene screw cap with silicone gasket pouring ring and compression fitting.

Thermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube. Thermowell assemblies for 1965 and 1967-style angled sidearm…

Heating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 500ml Watts: 50 Dimension (in.): 1 x 10.5 1 latch 6f cord…

Spring-loaded to stay open until used. Cuts tubing up to 1-1/2 in. (38 mm) diameter. Made of nickel-plated zinc-alloy die-casting.

Gently introduces bubbles into vessels. Includes 45mm polypropylene cap and white silicone gasket. 316l stainless steel 20 ra finish Size: 3l 12mm od coarse glass frit 0.2um Acrodisc filter w/ hose fitting