Ace Glass, Stirrers
-
Stirring Blade, For 5 & 6mm Shaft
Ace GlassPTFE stirring blades for use with our button type 9524 and 9527 stirring shafts. Blades are 41mm wide x 12mm high and are designed for use in flasks 250ml and less. Match blade to shaft OD.
-
STIR-LUBE®,Trubore® Stirrer Lubricant
Ace GlassA superior, low melting, silicone base lubricant which liquefies at body temperature. Because of its composition, you need apply only a very thin film of Stir-Lube® to a stirring shaft to increase bearing and shaft life at least three times over that of a bearing lubricated with glycerine.…
-
Stirring Shaft, Glass, Polished, 10mm
Ace GlassPolished glass stirring shafts, 10mm OD. Recommended for use with only our 8050,8066,13443 and 13445 bearings. Join 8083,8085,8086,8087,8096 blades to button type shafts. Join 8088, 8089, 8090 & 8091 agitators to bead type shafts. Plain shafts will accept 8094 & 8095 agitators secured with a…
-
Glass bearing design for use with Ace-Thred pressure reactors and our 8075 glass, polished or 8074 bare, stainless steel 10mm stirring shafts. Both the top bushing and bottom coupling are PTFE. Maximum operating speed is 600 rpm.
-
Polished stainless steel stirring shafts, 10mm OD, drilled type with removable button. When used with 8066 PTFE bearing, a lubricant-free vacuum seal can be realized at speeds up to 200 rpm. Recommended for use with 8044,8050,8066,13443 and 13445 bearings. With button, shaft accepts…
-
Stirrer, Laboratory, Solid State
Ace GlassTotally enclosed, 1/40hp DC permanent magnet motor with dual 8 mm (5/16") armature and gear shafts with milled flats. Armature shaft with maximum speed of 4000rpm.; 18:1 ratio gear shaft rated 3.6in-lb torque, up to 333rpm. Motor supplied with 1.5 meter 3-wire cable for controller connection.…
-
Stirring shaft agitator combination available in either a solid, precision ground glass shaft or all PTFE knob type shaft with a PTFE snap-fit agitator designed to fit through 14/20 and 18/11 joints. Designed for use with our 5mm ID 9524 or 9527 bearings and flasks of 50ml and smaller.
-
Stirrer Blades, PTFE
Ace GlassPTFE stir blades for button type stir shafts. 10mm OD shafts can be found in our product series 8068, 8070, 8074 and 8075. 19mm OD shafts can be found in our 8076 and 8077 series.
-
Bearing, Trubore, Ace-Thred, 10mm
Ace GlassSelf-aligning, three-piece bearing. Complete consists of inner Trubore bearing, Nylon bushing with O-Ring, and threaded adapter. Unique design eliminates costly replacement since inner bearing will spin if shaft binds or will self-align at O-Ring seal in the event the motor is slightly cocked.…
-
PTFE banana shaped stir blades for 10mm OD button type stir shafts. 3mm thick blades have a number of perforations and are designed to closely fit various sizes of round bottom flasks. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.
-
Trubore bearing, heavy duty, standard taper joint, self-aligning. Unique 3 piece design of Trubore inner bearing, compression seal nylon bushing and glass standard taper adapter allows for moderate misalignment of stir motor and the bearing cannot sieze the shaft. For use with 8077 & 8078 19mm od…
-
Stirring bars with large, 25mm (1 inch) raisied center ring.
-
Button type, solid glass stirring shafts, 5 & 6mm OD. Precision ground shafts, codes -04 & -06, should be used in matching glass Trubore 9524 and 9527 bearings. Polished shaft, code -40, should be used only in our 8066-120, 6mm PTFE inner bearing. All accept our 9542 blades. Join to stirrer motor…
-
PTFE agitator with removable blade secured with a PTFE pin. Supplied 76mm long blade will fit through a 29/42 joint. Fits 10mm OD drilled type or beaded type 8068, 8071 and 8075 shafts.
-
Stirrer, Vacuum, Debris Free
Ace GlassA rugged, compact, inexpensive stirrer. The upper member turns with stirring shaft, bottom member remains stationary. Upper member supplied with vinyl connector. Use with ACE 8134 stirring shafts. Assembly may also be used to make your own rotary evaporator.
-
Bearing, Trubore, 10mm
Ace GlassFor use with Flask Head 9443. By using precision bore tubing throughout the length of the bearing, a stirrer is produced that will hold to within 1mm of vacuum and withstand pressures in the flask up to 300mm. The 9532 Agitator, used with this bearing actually develops a negative pressure of 230mm…
-
Stirring Shaft, PTFE Coated Glass, 10mm
Ace GlassPrecision ground glass stirring shafts, 10mm OD, button type, PTFE coating permits higher stirring speeds with Trubore bearings. If used unlubricated, 500 rpm max with water-cooled 8040 bearing. Compatible with 8036, 8038, 8039, 8043, 8047, 8051, 8055 and 13443 bearings. Button type shafts accept…
-
Stirrer Blades, PTFE, Oval, 10mm Shafts
Ace GlassPTFE oval stir blades for 10mm OD button type stir shafts. 10mm OD shafts can be found in our 8068, 8070, 8074 and 8075 series.
-
PTFE, large-scale, multi-paddle agitator design to accept pinned bottom valves, like our 6482 flush-seal valve. The pin helps reduce wobble or flexing at higher rpm. 19mm agitators will fit drilled type or knob type 8076, 8078 and 8079 shafts.
-
Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8074 stainless steel or 8075 polished 10mm od glass shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…
-
Stir Shaft, Retreat Agitator, PTFE
Ace GlassPTFE covered stainless steel shaft with a solid PTFE retreat curve agitator. Featuring a retreat angle of 30 degrees and, for a better grip by the stir motor chuck,50mm of exposed stainless.
-
Precision PTFE covered stainless steel stirring shafts, 19mm OD. Drilled type shafts accept 8091,8092,8093,8100 agitators and can be used in 19mm Trubore bearings (8059, 8060, 8061 & 8065). Not recommended for PTFE bearings 8050, 8067 and 13445. Join to stirrer motor using 8124 series chucks.
-
Precision ground glass stirring shafts,10mm OD, crescent type. Useful for stirring viscous materials at low rpm. Available for round bottom flasks of 1, 3 and 5 liters. Code -19, 3 liter size will fit a 2 liter flask, but closely. Flask opening must be 29/42 or larger. Use with Trubore bearings…
-
With buffered load control and DC filtration. Ratings: AC three-prong output socket, standard NEMA type, 1200 watts. 0 -120 volts, variable, 60 Hz. maximum 10 amps. DC four-prong output socket, cinch type. 360 watts, 0 -150 volts, variable, filtered approximately 1/2 hp.max. 3 amps. A solid state…
-
Stirring Shaft Coupling
Ace GlassStir shaft couplings for connecting glass or metal stir shafts to the adjustable chuck on an overhead stir motor. Compression connection is secured to various OD shafts via an Allen screw coupling. The Codes -22 and -24 are complete pass-thru assemblies that enable height adjustment on stir shafts…
-
Air Motor, Heavy Duty
Ace GlassA compact, heavy duty air motor with highly damped muffler. Complete unit consists of an air hose with a snap coupling on motor end and shut-off valve on the other. Motor will develop 1.5 hp. at 90 lbs. air pressure. Speeds are variable from 300 to 3000 r.p.m. It consumes approximately 1.98m3 free…
-
Fully flexible drive shaft facilitates isolation of the stirrer motor from the reactor. Complete units, code -30 (91.4cm) and code -32 (152.4cm), designed for use with 8mm (5/16in) motor shaft. Purchase the optional code -27 adapter for motors with 9.5mm (3/8in) shafts. Reactor end consists of a…
-
Agitator, PTFE, Large scale, Turbine
Ace GlassA turbine type agitator, available for 19mm and 28mm shafts. 19mm six blade agitators are open in the center to allow custom positioning on drilled type or knob type 8076, 8078 & 8079 shafts. 28mm four blade agitators are supplied with a PTFE nut & bolt set for securing to 8080 shafts. Shaft is not included.
-
Bearing, Trubore, 5 & 6mm
Ace GlassTrubore bearing with standard taper joint for use with our 9534, 9535 and 9541 precision ground stir shafts. Lubricant well at top will accept enough 8117 Stir-Lube to provide hours of operation at up to 1000 rpm. Match bearing ID with stir shaft OD.
-
Stirrer Assembly, Vacuum, Debris Free
Ace GlassRotating ball joint seal gives vacuum-tight connection good into the micron range. Ultimate vacuum is determined primarily by the tightness of the vinyl tubing connector which fastens the unground shaft to the ball member. Operate below 500 rpm. Use with unground stirring shafts (8134,9530).…
-
Chuck, Flex-Grip®
Ace GlassNylon chuck for use with ACE stirring shafts or other shafts of the same dimensions. Chuck has flexible insert which allows for misalignment of shaft without danger of breakage.
-
Pass-Thru Rod, Flexible shaft
Ace GlassPass-thru rod for use with Caframo 13565 & 13566 stir motors attached to our 8081 flexible stirring shaft.