Supplies, Kemtech America, Glass
-
Synthware Distilling Adapters, 75°
Kemtech AmericaSynthware distilling adapter with top compression cap. With same size standard taper inner joints on bottom and side arm. Cap accomodates 5.0 - 7.5mm O.D. thermometer. Supplied with one Nylon cap and one Viton o-ring.
-
Synthware Inert Gas Adapters with 2 Hose Connections
Kemtech AmericaSynthware Inert Gas Adapter has two hose connections 180 degrees from one another to provide a flow of inert gas over the apparatus. The joints are standard taper inner joints.
-
Peptide Synthesis Vessel, Solid Phase, Vacuum, Synthware, Capacity: 10-100mL available, Frit Porosity: Medium abd Coarse availabe, Frit OD: 15-40mm available, GL Thread: 14 or 25 available, Hose Connection OD: 8mm, Supplied with PTFE lined screw cap and straight bore stopcock with 2mm bore.
-
Synthware Claisen Adapters, Modified
Kemtech AmericaIt is modified with an additional side arm at 45 degrees to the vertical outer joint. All joints are the same size.
-
SYNTHWARE Snyder Distillation Column
Kemtech AmericaSnyder Distillation Column, 3 Section Top Outer Joint: 24/40 Lower Inner Joint: 24/40 Column Height: 150mm Overall Height: 300mm For use with Kuderna-Danish flask.
-
Kjeldahl Trap Adapters
Kemtech AmericaSynthware distillation adapter with Kjeldahl trap. With two standard taper inner joints that are parallel and at a 75 degree angle to the connecting tube. Distance between joints is approximately 200mm.
-
Synthware Inlet Adapters with Extended Length Lower Tubes
Kemtech AmericaSynthware inlet adapter with extended length lower tube. Allows for the introduction of reactants below the interior surface. Tube extends 153mm (6 inches) below the joint. Tubing has the same O.D. on both ends of the joint.
-
Synthware Inlet Adapters
Kemtech AmericaFor use with gas inlet tubes or plain stem thermometers. Supplied with one holed rubber adapter.
-
SYNTHWARE Solvent Still Head with Drainage Port
Kemtech AmericaSolvent Still Head Capacity: 500 and 1000mL available Top Joint: 24/40 Bottom Joint: 24/40 and 29/42 available Side Joint: 14/20 Drainage Port Joint: 14/20
-
SYNTHWARE Distilling Heads for 76mm Thermometers
Kemtech AmericaThermometer joint is 10/18 for 76mm immersion thermometer. Side arm is at 75° angle.
-
Synthware "U" Shaped Drying Tubes
Kemtech AmericaSynthware "U" shaped drying tube. With a lower inner standard taper joint. Cotton is typically used to contain drying agent.
-
SYNTHWARE Glass Check Valves
Kemtech AmericaCheck Valve, All Glass, Synthware, Hose Connections OD: 8mm, with ground seat for liquid seal.
-
SYNTHWARE Solvent Still Head
Kemtech AmericaSolvent Still Head Capacity: 500 and 1000mL available Top Joint: 24/40 Bottom Joint: 24/40 Side Joint: 14/20
-
SYNTHWARE Distillation Cow Receiver
Kemtech AmericaDesigned for microscale application. With one female joint and four drip-tip male joints.
-
Synthware Rotary Evaporator Anti-Splash Traps
Kemtech AmericaTrap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With upper outer and lower inner standard taper joints.
-
SYNTHWARE Hickman-Hinkle Still Head with Side Port
Kemtech AmericaHickman-Hinkle Still Head, with Side Port, Synthware, Joint: 14/10, for microscale fractional distillation, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.
-
SYNTHWARE Shortpath Distilling Head for Volatile Distillants
Kemtech AmericaWith the condenser being a combination of a cold coil and Leibig. Top outer joint is a 10/18 for use with a 50mm immersion thermometer. With Vigreux Indentations.
-
SYNTHWARE Inlet Connecting Adapter
Kemtech AmericaInlet Connecting Adapter, High Vacuum Valve Joint: #15 O-ring Valve Size: 0-4mm Side Port: 10mm OD.
-
Synthware Vacuum/Argon/Nitrogen Inlet Adapters
Kemtech AmericaAllows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure.
-
Synthware Enlarging Adapters
Kemtech AmericaSynthware enlarging adapters are used for connecting dissimilar standard taper joint sizes. The lower inner joint is smaller in size than the top outer joint.
-
SYNTHWARE Inlet/Thermometer Adapter
Kemtech AmericaThermometer Adapter, Microscale, Synthware, Joints: 14/10, Thermometer OD: 5.0-7.5mm, supplied with one compression cap and one Viton O-ring.
-
Synthware Distillation Adapters, Vacuum Jacketed
Kemtech AmericaCan be used as a distilling head to connect a condenser to the top of the distillation column. The 10/18 top joint accomadates a 76mm immersion thermometer.
-
SYNTHWARE Short Path Distilling Head for Volatile Solvents
Kemtech AmericaWith the condenser being a combination of a cold coil and Leibig. Top outer joint is a 10/18 for use with a 50mm immersion thermometer. For best result, use D272440.
-
Synthware Straight Drying Tubes
Kemtech AmericaSynthware straight drying tube. With top outer and lower inner standard taper joints of the same size.
-
SYNTHWARE Microscale Distillation Apparatus
Kemtech AmericaMicroscale Distillation Apparatus has a short-path design for microscale application, used with 25mm immersion thermometer, and D27 distillation receiver.
-
SYNTHWARE Vertical Orientation Distrubution Adapter
Kemtech AmericaRotating distillation receiver allows four fractions to be collected. Vacuum adapter has a vertical orientation.
-
SYNTHWARE Jacketed Micro Vigreux Distillation Head
Kemtech AmericaDistillation Head, Vigreux, Jacketed Thermometer Joint: 10/18 Joints: 14/20, use with 25mm immersion thermometer
-
SYNTHWARE Adapter with #15 O-Ring Joint to Inner Joint
Kemtech AmericaAdapter, #15 O-ring joint to 14/20, 19/22 or 24/40 inner joint
-
Synthware Claisen Adapters
Kemtech AmericaProvides dual entry into a variety of flasks. Adapter has standard taper outer joints at top and on side and inner joint on bottom. All joints are the same size.
-
Synthware Distilling Adapters, 105°
Kemtech AmericaSynthware distillation adapter with sealed in drip tip. Adapter is bent at 105 degrees. Standard taper top outer joint and lower inner joints.
-
SYNTHWARE T-Shaped Connecting Tubes
Kemtech AmericaConnecting Tube, T-shaped, Synthware, Tubing OD: 8 and 10mm available.
-
Synthware Reducing Adapters
Kemtech AmericaSynthware reducing adapters are used for connecting dissimilar standard taper joint sizes. The lower inner joint is larger in size than the top outer joint.
![Site Search powered by SLI Systems](http://assets.resultspage.com/logos/sli_logo_2014.png)