Vials, MilliporeSigma, Chromatography Vials, CE and CE/MS
-
Vials, screw top with solid green Thermoset cap
MilliporeSigmaSynonyms: PK100 7ML AMBER VIAL,SCREW TOP, SOLID CAP W/PTFE LINER
-
Inserts for 2 mL large opening vials
MilliporeSigmaInsert fits 12 x 32 mm vials with large opening (6.0 mm)
-
Vials, screw top
MilliporeSigmaApplication: Vials may be used in headspace solid-phase microextraction (SPME) followed by GC-FID for simultaneous analysis of furan, 2-methylfuran and 2-pentylfuran from juice samples.
-
Crimp seal with PTFE/butyl septa aluminum seal
MilliporeSigmaCrimp seals, 11 mm, with PTFE/rubber septa are for use with 20 mm crimp top vials. The PTFE/rubber septa are compatible with most organic solvents many organic solvents: acetic acid (
-
ABC Vial™
MilliporeSigmaABC Vials have a unique 9 mm thread design that allows screwing on the caps, and still using them in a robotic autosampler. This thread is much higher on the top of the vial allowing space between the bottom of the thread and the shoulder of the vial. Legal Information: ABC Vial is a trademark…
-
Certified glass inserts
MilliporeSigmaOther Notes: Large opening inserts fits crimp seal, snap ring, and 9 mm threaded vials (with 6.0 mm ID)
-
Short thread screw cap
MilliporeSigmaShort thread screw cap, 9 mm thread, with liner are suitable for use with short thread (11.6 X 32 mm) autosampler vials (9 mm thread). The PTFE/rubber septa are compatible with most organic solvents until pierced and are not recommended for aromatics, carbon disulfides, chlorinated solvents,…
-
Certified Vial Kit, Low Adsorption (LA)
MilliporeSigmaSupelco's new Low Adsorption (LA) vials are manufactured using a process that decreases the number of hydroxyl groups on the vial's glass surface, significantly reducing surface activity while improving analytical quantitation and minimizing pH shifts in the sample. This same process also removes…
-
Certified Vial Kit, Low Adsorption (LA)
MilliporeSigmaSupelco's new Low Adsorption (LA) vials are manufactured using a process that decreases the number of hydroxyl groups on the vial's glass surface, significantly reducing surface activity while improving analytical quantitation and minimizing pH shifts in the sample. This same process also removes…
-
Assembled screw cap
MilliporeSigmaApplication: Assembled screw cap with hole and PTFE/silicone septum may be used to minimise the risk of explosion of diazomethane, during preparation of diazomethane for gas chromatographic analysis. It was also used to seal off the heat treated samples, during determination of sugar-amino acid…
-
Application: It may be used to cut and store fresh plant material for collecting volatiles in solid phase microextraction (SPME) technique. It may also be used in liquid chromatography-tandem mass spectrometry (LC-MS/MS) method for determining bisphenol A, 4-t-octylphenol and 4-nonylphenol in…
-
Screw cap, phenolic
MilliporeSigmaScrew caps (black phenolic hole cap, for use with 7 mL vial with 15-425 thread) are available as hole caps for use with sealing septa. Caps are offered in phenolic resin. Phenolic hole caps can withstand a maximum temperature of 149C.
-
Septa, tan PTFE/silicone
MilliporeSigmaApplication: Septa, tan PTFE/silicone has been used to seal the reactivial containing the by-product sample of snow crab, which is subjected to alkaline liquid phase hydrolysis. Legal Information: Tenax is a registered trademark of Buchem B.V.
-
ABC Vial™
MilliporeSigmaThese vials have a 9mm thread that allows them to be used with robotic systems. Use with autosamplers that require 12 x 32 mm screw top or crimp top vials. •40% wider opeing than standard screw cap vials •Superior thread design ensures a secure seal •Compatible with most GC autosamplers that…
-
Screw cap
MilliporeSigmaScrew caps [for use with 2 mL vial (standard opening), thread 8-425] are available for use with sealing septa and solid caps with aluminum liners. Caps are offered in solid phenolic caps that can withstand a maximum temperature of 135 C.
-
-
White polypropylene EPA Vials
MilliporeSigmaEach of the vials is cleaned according to US EPA Protocol B: The cleaning procedure is as follows:1. Wash containers in hot water using laboratory grade non-phosphate detergent.2. Rinse three times with copious amounts of tap water to remove detergent.3. Rinse three times with ASTM Type I…
-
Standard screw-thread autosampler vials
MilliporeSigmaConstructed of borosilicate glass. Vials use 8mm septa and screw-caps
-
Certified screw thread vials
MilliporeSigmaOther Notes: The inside diameter of vials vary with the manufacture. The following insert part numbers are compatible with these large opening vials. •29435-U PK100, Certified 200 muL glass inserts, mandrel precision point, 6 X 29mm, with bottom spring •29436-U PK100, Certified 250 muL glass…
-
Certified glass inserts
MilliporeSigmaOther Notes: Large opening inserts fits crimp seal, snap ring, and 9 mm threaded vials (with 6.0 mm ID)
-
Headspace vial, beveled top, rounded bottom volume
MilliporeSigmaHeadspace vials are available in several sizes. The style and diameter of headspace vials depend on the autosampler. Vials with rounded bottoms are sturdier and more resistant to pressure than the flat bottom vial. The rounded bottom version was created to allow the vial, when transported by a…
-
-
Application: It may also be used in automated solid-phase microextraction-gas chromatography-mass selective detection (AutoSPME-GC-MSD) analyses for the determination of sugar-amino acid reaction mechanisms and production of branched-chain alkyl-substituted pyrazines.
-
Crimp seals with PTFE/silicone septa silver aluminum seal
MilliporeSigmaApplication: Crimp seals with PTFE/silicone septa may be used to seal the water samples during the analysis of BTEX in BTEX contaminated waters, using static headspace extraction, followed by gas chromatography with photoionization detection (HS-GC-PID).
-
-
Septa, PTFE/Silicone
MilliporeSigmaApplication: Septa may be used in headspace solid-phase microextraction (SPME) (lyophilized aqueous extract).
-
Crimp seals with PTFE/silicone septa aluminum seal
MilliporeSigmaIt is used as an air-tight seal, and prevents contamintion
-
Insert for 2 mL standard opening vial
MilliporeSigmaVial inserts basically permit the use of smaller sample volumes with standard autosampler vials. Inserts are generally chosen based on the inner diameter of the vial neck. Standard opening vials (4.6 mm ID) require a 5 mm OD insert.
-
Wheaton sample vials with rubber lined caps
MilliporeSigmaCaps have white styrene-butadiene rubber liner and are packed in Lab-File® cases. Clear Wheaton-33, low extractable borosilicate glass or amber Wheaton-320 glass. Can be sterilized and stored at low temperatures. Legal Information: Lab File is a registered trademark of Wheaton Industries, Inc.
-
Headspace vial, clear glass
MilliporeSigmaApplication: Headspace vial may be used in storing samples for stability analysis of freeze dried and fluid bed dried alginate microcapsules coated with chitosan containing model probiotic bacteria, Lactobacillus plantarum. Legal Information: WHEATON is a registered trademark of Wheaton…
-
Vials, screw top
MilliporeSigmaApplication: Vials may be used in headspace solid-phase microextraction (SPME) followed by GC-FID for simultaneous analysis of furan, 2-methylfuran and 2-pentylfuran from juice samples.
-
Wheaton sample vials with rubber lined caps
MilliporeSigmaCaps have white styrene-butadiene rubber liner and are packed in Lab-File® cases. Clear Wheaton-33, low extractable borosilicate glass or amber Wheaton-320 glass. Can be sterilized and stored at low temperatures. Legal Information: Lab File is a registered trademark of Wheaton Industries, Inc.