With buffered load control and DC filtration. Ratings: AC three-prong output socket, standard NEMA type, 1200 watts. 0 -120 volts, variable, 60 Hz. maximum 10 amps. DC four-prong output socket, cinch type. 360 watts, 0 -150 volts, variable, filtered approximately 1/2 hp.max. 3 amps. A solid state…

Trubore bearing, heavy duty, standard taper joint, self-aligning. Unique design is forgiving of slight misalignment of stir motor and shaft. Recommended for use with our 9534 6mm precision ground stir shaft.

Offset gearbox and motors complete with right angle drive unit for pilot plant systems. Motors with right-angle drive save headspace and work well where height is restricted. Available for standard or hazardous duty applications. Available in either 1/4hp or 1/2hp with a digital 115/230v 50/60Hz…

PTFE covered stainless steel shaft with a solid PTFE retreat curve agitator. Featuring a retreat angle of 30 degrees and, for a better grip by the stir motor chuck,50mm of exposed stainless.

Rated 1 hp. for use with most stirrer motors. Not for use with shunt wound DC motors. A compact, lightweight, solid state, ring stand mountable control unit, both AC and DC outlets. Pulsed AC gives better low speed torque than voltage dropping devices such as rheostat or transformer. AC output: 120…

PTFE covered stainless steel shaft with solid PTFE, 4 blade screw propeller. Blades are pitched 45 degrees. For a better grip by the stir motor chuck, 50mm of stainless is left exposed.

Pass-thru rod for use with Caframo 13565 & 13566 stir motors attached to our 8081 flexible stirring shaft.

Totally enclosed, 1/40hp DC permanent magnet motor with dual 8 mm (5/16") armature and gear shafts with milled flats. Armature shaft with maximum speed of 4000rpm.; 18:1 ratio gear shaft rated 3.6in-lb torque, up to 333rpm. Motor supplied with 1.5 meter 3-wire cable for controller connection.…

3/8HP Brushless DC motor for use on pilot plant reactors up ²to 200L. May be used with either the 120V or 240V BLDC ²motor controllers. Supplied with 6ft removable cable and ²mounting hardware.

Trubore bearing with standard taper joint for use with our 9534, 9535 and 9541 precision ground stir shafts. Lubricant well at top will accept enough 8117 Stir-Lube to provide hours of operation at up to 1000 rpm. Match bearing ID with stir shaft OD.

Motor, AC variable, hazardous duty, 1/2hp,230/460v 60Hz²3 phase, complete with controller, 115v 50/60Hz input, CE and ²cULus rated. Control box cord to motor is 12ft long, control²box cord to electrial source is 24ft long.

A compact, heavy duty air motor with highly damped muffler. Complete unit consists of an air hose with a snap coupling on motor end and shut-off valve on the other. Motor will develop 1.5 hp. at 90 lbs. air pressure. Speeds are variable from 300 to 3000 r.p.m. It consumes approximately 1.98m3 free…

Rotating ball joint seal gives vacuum-tight connection good into the micron range. Ultimate vacuum is determined primarily by the tightness of the vinyl tubing connector which fastens the unground shaft to the ball member. Operate below 500 rpm. Use with unground stirring shafts (8134,9530).…

Jacketed, Trubore bearing with standard taper joint for use with our 9534, 9535 and 9541 precision ground stir shafts. Hose connections fit 5/16" or 3/8" ID tubing. Match bearing ID of 5 or 6mm to stir shaft OD.