Accurately and precisely dispense liquids for QuEChERS extractions with this versatile pump. A quick, simple adjustment lets you set the output volume anywhere from 2.5 mL to 30 mL per stroke, and the included adaptors will accommodate most reagent bottles. Adjustment knob offers 56 output…

Oil-free vacuum pumps are piston powered, so they do not pollute the air and require minimal maintenance Quiet, low-vibration units keep disturbances to a minimum Built-in thermal protector automatically shuts off pump if it overheats and then restarts it once the unit is cool Inlet filter…

Luer lock inlet offers leak-tight syringe connection Variety of filter types, porosities, and diameters Color coded for easy identification Rugged polypropylene housing Autoclavable to 121°C for 15 minutes Quantity break pricing for greater savings Cellulose Acetate, Nylon,…

2-inch vacuum/pressure gauges, 316 stainless steel with 1/8" NPT fitting and center back mount. Recommended for use with canisters.

Sampling bags are a low-cost whole air sampling device for high level VOCs and permanent gases. Several EPA, NIOSH, and OSHA methods exist for bag sampling for a variety of applications: stationary sources emissions; workplace atmospheres; ambient, indoor air quality; and breath analysis. Choose…

High-quality vacuum gauges with 316 stainless steel wetted surfaces. –30" Hg to 0" Hg. Recommended for use with passive sampling kits. All are rear mount.

Sampling bags are a low-cost whole air sampling device for high level VOCs and permanent gases. Several EPA, NIOSH, and OSHA methods exist for bag sampling for a variety of applications: stationary sources emissions; workplace atmospheres; ambient, indoor air quality; and breath analysis. Choose…

Restek’s passive air sampling kit incorporates all the hardware necessary to collect air samples and is easy to assemble for field sampling.* Kit includes flow controller, critical orifice, 2 µm frit filter, vacuum gauge, and sample inlet. The gauge and sample inlet are downsized for…

Quickly and precisely verify flow rates generated by vacuum or pressure before going into the field. These compact, convenient units are ideal for real-time calibration of air flow controllers, passive sampling kits, air canisters, sampling pumps, and more. They measure absolute pressure, mass…

High-accuracy test gauges are recommended for verifying the vacuum/pressure in canisters before and after sampling. The 6-inch face on the analog gauge allows for easy reading. The digital gauge operates on two AAA batteries and offers an unambiguous readout. Both gauges have an accuracy of +/–…

This cylinder stand is designed to support small-diameter cylinders, such as 104L and 110L disposable cylinders. It is a simple, safe, and economical way to stabilize the position of small cylinders, while keeping them within close proximity. The stand is constructed of heavyweight painted steel…

Robust, low-flow pump optimized for sampling volatile organic compounds (VOCs) onto thermal desorption (TD) sorbent tubes Small, lightweight, easy to use, and intrinsically safe—ideal for personal monitoring and a wide range of other air and gas sampling applications Compatible with any…

General Description For continuous "hands off" direct transfer of multiple liquid samples A Visiprep large volume sampler enables you to transfer low viscosity samples directly from any sample container to conventional solid phase extraction tubes on a Visiprep SPE vacuum…

Polypropylene protein precipitation (PPT) 96-well plates offer highly efficient >99% protein removal Minimum 24-hour drip-free feature for easy in-well protein precipitation—no fear of backflushing or contamination Built-in dual-layer membrane with different porosities in each layer…

For ultimate inertness, SilcoCan air sampling canisters feature our unique Siltek treatment technology. Even highly active components, at low parts-per-billion concentrations, can be readily sampled and stored without loss. The RAVE valve is a high-quality, metal-to-metal seal, 2/3-turn valve with…

High quality anhydrous sodium sulfate Approximately 2 grams prepackaged in a convenient capped cartridge with both male and female luer ends for easy connection to a variety of devices or equipment The adsorbent is fully activated and ready to use for removal of excess water from organic…

Anhydrous sodium sulfate is the most common drying agent used to remove moisture from sample extracts. We package our 10-60 mesh material in recloseable buckets. Ideal for removing water from sample extracts Activate by heating to 400°C for four hours before use Packaged in…

Free-flowing salts transfer easily and completely. Easy-open packets eliminate the need for a second empty tube for salt transfer. Convenient slim packets fit perfectly into tubes to prevent spills. Ready-to-use tubes, no glassware required. Pre-weighed, ultra-pure extraction salts. …

Activated copper effectively removes elemental sulfur from environmental extracts. Our acid-washed and activated material can be used right out of the package. The 30 mesh granular material eliminates the potential for fine copper particles in filtered extracts. Convenient form for removing…

Convenient storage of extraction cell parts and consumables Thirteen open bins provide easy visibility and organization for small and large pieces Small footprint conserves valuable lab bench and drawer space

Glass fiber disks embedded with C18 or C8 bonded silica Extract semivolatile organic compounds Deep-pore design reduces clogging and allows faster flow rates Meet requirements for EPA Methods 525.1, 506, 550.1, and 549.1 Lower cost than PTFE disks

For use in critical orifice fitting. Includes washers.

Replacement Septum for Tedlar, ALTEF, and Multi-Layer Bag Valves, 4mm diameter, PTFE-faced silicone.

Styrene/divinylbenzene, equivalent to XAD-2 resin Untreated, packaged in 1 kg plastic containers Spherical, 20 to 60 mesh particles

New personal air sampling technology designed to meet OSHA and NIOSH requirements for industrial hygiene applications Quiet, robust sampler does not require a pump and manages variations in face velocity, temperature, and humidity better than traditional sampling approaches Easy to…

Optimized for Methods TO-14A, TO-15, IP-1A, ASTM D5466, OSHA PV 2120, and NJ DEP Low Level TO-15 Proprietary electropolished surface maintains compound stability. High-quality, metal-to-metal seal, 2/3-turn valve with stainless steel diaphragms prevent sample adsorption for more-accurate…

When cleaning SilcoCan or TO-Can canisters, it is important to use humidified air or nitrogen to help remove volatile organic contaminants. Restek's humidification chamber is made of acrylic and withstands pressure up to 90 psi. The 1/4-inch inlet and outlet compression fittings allow easy…

These small canisters are designed for controlled sampling, such as personal air sampling, as an alternative to tube and pump samplers. The 1,000 cc canister is suitable for sampling volatile organic compounds in air according to methods TO-14A, TO-15, IP-1A, ASTM 5466, OSHA PV 2120, and NJ DEP Low…

Firm nylon bristle brushes for easy cell cleaning and removal of solid samples Range of sizes to fit all extraction cells for ASE 100, 200, and 300

Accelerated solvent extraction is a common technique for fast and reliable extraction of organic materials from solid matrices, using EPA SW-846 Method 3545, Pressurized Fluid Extraction (PFE). Restek offers a wide range of replacement parts to keep your extraction system running smoothly. All…

The model 1062 vacuum bag sampler provides fast sampling with zero cross-contamination. A vacuum created in the box draws air into the sampling bag without drawing it through the vacuum pump first, as is the case with standard air sampling pumps, thereby preventing contamination of the sample. This…