Labconco Hoods
-
SpillStopper Work Surface molded of corrosion-resistant solid epoxy. Dished & contoured to conform to interior liner of Protector Pass-Through Hoods. Pre-drilled 2.5" (6.4cm) dia plumbing holes.
-
Protector Filtered Fume Hoods
LabconcoNeutrodine Unisorb Molecular Filter Neutrodine Unisorb molecular carbon filter unit for multi-purpose use of acids/bases/solvents, separated or combined. Compatible with 500+ chemicals. For use with Protector Echo and Airo Filtered Hoods. 1 EA. HEPA Filter, 99.995% efficient, H14 type, for…
-
Solid Epoxy Work Surfaces
LabconcoBlack chemical-resistant work surface is contoured to fit the dimensions of the enclosure and to contain spills. These surfaces can be used with Protector XVS Ventilation Stations, Protector Work Stations, Purifier Non-Ventilated PCR Enclosures and Tissue Culture Enclosures.
-
SpillStopper Work Surfaces are compatible with Protector (Premier or XStream) Laboratory Hoods with Eco-Foil(TM) Air Foil. Molded from a special formulation of corrosion-resistant epoxy resins, these work surfaces are dished and contoured to conform to the interior liner of Protector Laboratory…
-
Protector XStream Laboratory Hood
LabconcoThe newly redesigned, patented* Protector XStream Laboratory Hood was engineered to be the best containing fume hood possible. Testing shows the Protector XStream easily meets containment per SEFA-1 low velocity hood standards when subjected to the ASHRAE 110 test protocol with results of less than…
-
Spiral Tube
LabconcoCorrosion-resistant, neoprene-impregnated fiberglass reinforced with steel wire. Include rigid duct connector and two clamps. Because this ductwork is flexible and may conform to various configurations, it is not possible to know the precise equivalent resistance.
-
The Purifier Axiom Class II, Type C1 is the first biological safety cabinet that can be used in a recirculating Type A-mode for standard microbiological work, or can be connected to an exhaust system to function in Type-B mode for handling hazardous chemical vapors or radionuclides. Because of the…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
Wash Rings
LabconcoWash Ring, wide angle conical spray nozzle, and wash water connection nipple are fabricated into a PVC coupling. For Stainless Steel or PVC Perchloric Acid Hoods. 10" Diameter Flow rate is one gallon per minute at 40 psi. 12" Diameter Flow rate is 0.70 gallons per minute at 20 psi.
-
Protector XL Floor-Mounted Laboratory Hoods (sometimes called Walk-In Hoods) accommodate laboratory procedures that require oversized equipment or maximum working height. Models with horizontal-sliding sashes have a loading height of 73.5” (186.7 cm), suitable for applications requiring…
-
XPert Balance Enclosure Stations
LabconcoXPert Filtered Balance Stations are designed to protect the user during powder weighing operations. Ducting to an outside blower is required. Patented features include an ergonomic air foil with Clean-Sweep openings to enhance airflow and a zone-perforated rear baffle that creates horizontal…
-
SpillStopper™ Work Surfaces, 4' Wide
LabconcoSpillStopper Work Surfaces are molded from a special formulation of corrosion-resistant epoxy resins. They are dished and contoured to conform to the interior liner of Protector Laboratory Hoods. The front edge has a large radius to aerodynamically direct airflow into the fume hood. Pre-drilled…
-
Ideal for fume hood exhaust systems in moderate to highly corrosive conditions. Intelli-Sense Multi-Speed Blowers are weatherized, direct drive, non-explosion-proof blowers controlled by a two or three position switch. Each blower has a reliable electronically commutated motor (ECM), which…
-
Thermoplastic Duct Reducers
LabconcoPVC coupling type reducer designed for connecting thermoplastic duct of different diameters with no equivalent resistance.
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
Protector PVC Perchloric Acid Laboratory Hood. 37.7" deep. Features heat-welded unplasticized PVC liner, built-in washdown system, integral work surface, drainage trough and 3/16" thick tempered safety glass vertical-rising sash with frame of powder-coated aluminum and PVC (glass is suitable for…
-
Protector Fume Hood Accessories
LabconcoScreen mounts behind the baffles for trapping tissue wipers & other papers. Each kit includes mounting hardware, powder-coated stainless steel screen & instructions. Contact Labconco for screens for hoods wider than 8'.
-
Fume Adsorbers
LabconcoTraps solvent vapors Fume Adsorber is designed for histology cover slipping and staining areas and uses activated carbon media to adsorb annoying odors and noxious vapors such as xylene and toluene. Solvent vapors are trapped in the capillary-like channels of the carbon filter while clean air is…
-
PVC T & Y Connections
LabconcoPVC fitting compatible with thermoplastic duct. End connections receive PVC pipe directly. 0516E96 - PVC "T" Connection: Duct Diameter: 10" Duct Diameter: 12" Duct Connection Diameters: 10" x 10" x 12" Height: 19" Equivalent Resistance in feet of Straight Duct: 20' …
-
Monitor features an LCD that displays average face velocity. Audible/visual alarm alerts user to low or high face velocity. Kit is for installation in a factory-prepared cutout on the upper portion of the right side fixture panel. Kits are available for use with 115V, 60 Hz operation or 230V,…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
SpillStopper™ Work Surfaces, 8' Wide
LabconcoSpillStopper Work Surfaces are molded from a special formulation of corrosion-resistant epoxy resins. They are dished and contoured to conform to the interior liner of Protector Laboratory Hoods. The front edge has a large radius to aerodynamically direct airflow into the fume hood. Pre-drilled…
-
Protector XVS Ventilation Station
LabconcoStandard or extra height models 2-, 3- or 4-feet wide Protector XVS Ventilation Station provides user protection by keeping powders and fumes contained during light duty, fume-generating or weighing procedures. Patented features include air foil with Clean-Sweep openings to enhance airflow and…
-
Sash stop kit
LabconcoSash Stop Kit. Restricts how far a vertical-rising sash may be opened. Compatible with Protector Xstream and Premier Fume Hoods