General Lab Products, Bellco Glass
-
Stainless Steel 2-Port Assembly 500mL 70mm
Bellco GlassAll port assemblies are manufactured from 316l stainless steel and have an electropolish finish. 2- port assemblies have siphon and vent tubes. 3-port assemblies have siphon, fill tube and vent tubes. All port assemblies include a 45mm blue polypropylene screw cap and white silicone gasket. Size:…
-
L-Bubbler Tube w/ Frit 8L
Bellco GlassSparging accessory for vertical sidearm spinner flasks. Manufactured from 316l stainless steel with electropolish finish. Includes polypropylene cap with 1/4? white compression fitting and white silicone gasket. .040 inch hole for aeration of fermentation cultures where shear force is less…
-
Valley Heating Blanket 115V-500mL 50 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Watts: 50 Dimension (in.): 1 1/2" tall x 10.5 diameter 1 latch 6f…
-
Stainless Steal Bioreactor Headplate 3L
Bellco GlassManufactured from 316l stainless steel with ra 32 finish or better inside and out. Fittings are sold separately as part of the system.
-
-
Glass Ball Impeller Only 6-8L
Bellco GlassGlass ball houses a magnet for gentle agitation of micro-carrier beads and has a 70mm cap. Specially formed bottom indent prevents accumulation under the impeller. Cap size: 100mm Size: 6-8l
-
Compression Fitting 2.5"
Bellco GlassBellco compression fittings are designed using our standard 45mm blue polypropylene open top caps and white silicone gaskets. A wide variety of fittings are available to allow ph and do monitoring via insertion of these probes into sidearms or vessels. Bellco probe adapters are designed to allow…
-
English threads Fits into 3/8" holes in headplate material 316l SST with electropolish finish - ra 32 finish inside & out Inside dimensions: .250" od x 19 1/4" overall length insertion length: 18" with hose barbs supply with SST nut & o-ring
-
Vent Filter Screw Cap 45mm
Bellco GlassManufactured from polypropylene. Ideal for addition and withdrawal of contents via syringe. 45mm cap has 33mm hole to accommodate 45mm septa or 45mm port assembly. 32mm cap has 20mm hole to accommodate 32mm septa or 32mm port assembly. Size: 32mm & 45mm O-ring seal Male luer lock
-
1.7in. Probe Holder 45mm
Bellco GlassBellco stainless steel probe holder is designed to be used with our 45mm blue polypropylene open top caps and white silicone gaskets. A wide variety of fittings are available to allow ph and do monitoring via insertion of these probes into the sidearms of the vessels. Threaded probe adapters are…
-
Micro-carrier Impeller Assembly 500mL
Bellco GlassImpeller assembly for micro-carrier spinner flasks. Consist of magnet holder, silicone plug, magnet, and ptfe paddle. Impeller size: 500ml Paddle dimensions: 1" x 3"
-
Stainless Probe Capseal 3L w/ PTFE IOB 4Ports
Bellco GlassThe stainless steel 100mm iob probe cap seal is manufactured from 316l stainless steel and has a red-silicone sealing gasket with a 100mm blue polypropylene screw cap. The stainless steel probe cap seal has four accessory ports surrounding a centrally located internal impeller assembly. Two of…
-
Low Profile 3-Port Harvest Assembly 3L
Bellco GlassMaterial: 316l SST with electropolish finish, ra 32 or better, inside & out Dimensions: harvest tube (3/8" od) - 1" above slug, 8 3/8" insertion length Addition tube (1/4"od) - 1" above slug, 2 21/64" below Vent tube (1/4" od) - 1" above slug, .975" below Supply with 45mm pp blue open top screw cap…
-
Stainless steel curved harvesting tube for 8l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 8l Dimensions: 1/4" x 5/32 x 20"
-
-
Low Profile 3-Port Sparger w/ Holes 3L
Bellco Glass316-l stainless steel ra32 or better finish .040? drilled holes sparger for low profile vertical side arm vessels. Threaded end is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket. Triple tube configuration with vent, fill/sample and sparge.
-
Silicone Headplate O-Ring 3L #254
Bellco GlassSilicone headplate o-ring for 3l bioreactor systems. Size: 254 Material: red silicone rubber Dimensions: od x id: 5.762?x 0.139? thick Size: #254
-
Silicone Headplate O-Ring 7L
Bellco GlassSilicone headplate o-ring for 7l bioreactor systems. Material: red silicone rubber Dimensions: od x id: 5.762?x 0.139? thick
-
IOB Impeller Assembly 500mL 70mm
Bellco GlassStainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks Cap size: 70mm Flask size: 500ml Paddle: 2" x 2"
-
Vessel Flange Gasket 10 For Bioreactor Vessels
Bellco GlassVessel flange gasket 10l for bioreactor vessels
-
Stainless steel curved harvesting tube for 8l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 8l Dimensions: 1/2" x .430 x 20"
-
Stainless Steel 2-Port Assembly 3L
Bellco GlassAll port assemblies are manufactured from 316l stainless steel and have an electropolish finish. 2- port assemblies have siphon and vent tubes. 3-port assemblies have siphon, fill tube and vent tubes. All port assemblies include a 45mm blue polypropylene screw cap and white silicone gasket. Size:…
-
Valley Heating Blanket 115V-15L-Low Watt 325 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 15l Watts: 325 - low wattage Dimension (in.): 5 x 33 1/4…
-
Bellco Heating Blanket 230V-3L 150 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 3l Watts: 150 Dimension (in.): 2 x 17.5 1 latch 6ft cord…
-
Bellco Heating Blanket 230V-15L 750 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 1200 - not to be use with CellTrol Watts: 1200 Dimension…
-
-
Large Flange Z/Z Paddle 36L
Bellco GlassManufactured from 316l stainless steel with electropolish finish. Ra 32 finish or better inside and out. Ideal use for cell culture and reduces shear in delicate cell culture. Blade dimension: 5 3/4 x 2? Shaft oal: 14 1/2? Constructed of 316l electropolished stainless steel Marine impeller includes…
-
IOB Impeller Assembly 8L
Bellco GlassStainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks. Cap size: 100mm Flask size: 8l Paddle: 6 3/4" x 5"
-
Sparger w/ Holes 3L
Bellco Glass316 l stainless steel sparger assembly with drilled holes for 3-liter bioreactor vessel. .250x.152 Welded flange,"3/8" Silicone 'o' ring
-
Digital Micro-Carrier Insect System 3L 230v
Bellco GlassDesigned for growing insect cell cultures such as sf9 and sf21 cells. The system comes complete with all accessories needed to grow your insect culture line for expression. Consist of: 7785-d2015 digital 5-position magnetic stirrer, 230v 1965-03000 micro-carrier spinner flask complete, 3l…
-
Screw Cap Assembly 38mm
Bellco GlassBlack phenolic screw caps are manufactured from specially formulated phenolic resin to resist the effects of temperature and steam autoclaving. They have a non-toxic white rubber liner for all general culture applications. Consists of screw cap liner and stopper or compression fitting Size: 38mm
-
Round Bottom Marine Impeller 15L
Bellco GlassBlade dimensions: 5 3/4" x 2" Shaft: 14 1/2" Stainless steel 4? od right hand pitch marine prop & e-clip Material: 316l stainless steel with electropolish finish For round bottom omni vessel (1964-88405) Need l/f head plate, over head drive motor
![Site Search powered by SLI Systems](http://assets.resultspage.com/logos/sli_logo_2014.png)