Ace Glass Filtering Funnels & Adapters
-
Funnel, Filter, Hirsch, Adjustable
Ace GlassMicroscale, vacuum adapter with vertically adjustable Hirsch filter funnel that is suitable for use with all Microscale flasks and vials with 14/10 joints. Two-piece adapter features a #7 Ace-Thred at top with a Nylon bushing and O-Ring that forms a compression seal with funnel stem, bottom joint,…
-
Cylindrical with joint at top and bottom and drip stem. Stopcock on equalizing arm permits filling funnel without having to open the system to atmosphere. For replacement stopcock plugs, see 8224. For stoppers, order 8250-12 or 8255-10.
-
Extraction Apparatus
Ace GlassDesigned for the extracting of liquids with ether. The dispersion of the ether is accomplished by the use of an ACE fritted disc, Por. B (70-100m), which is attached to the base of the funnel tube. With 24/40 and 40/50 joints. Available in the following sizes.
-
Instatherm Funnel, Addition
Ace GlassGraduated Instatherm® addition funnel provides precise heating for reactor systems demanding heated or constant temperature for the added reactants. Funnels feature standard taper outer top joints and bottom PTFE stopcock inner joints. All funnels include a 9698-20 connecting controller cord.
-
Funnel, Filter, 14/20
Ace GlassDiameter of sintered glass filter disc is 18mm. Measures 40mm from disc to bottom of joint. All porosities of a given size are priced the same. Volume approximately 10 mL. Hose connection is size A.
-
Funnel, Filter, Hirsch
Ace GlassUseful where it is necessary to wash the precipitation and redissolve with chemicals which would attack filter paper. Angle of funnel 60 degree.
-
Cylindrical, graduated reservoir permits determination of volume added at any time during pumping cycle. By stopcock manipulation, material may be pumped from graduated (10mL in 0.1mL) side tube only. This permits obtaining accurate pumping rate over short periods of time. Top joint is 24/40 outer.…
-
Funnel, Powder Dispensing
Ace GlassSide operated screw feed instrument for addition of powders and solids, up to 25 mesh, to reactions without problems of seizing or binding. Features a flexible PTFE screw thread wrapped on a precision PTFE-ceramic shaft and contained within a precision
-
Addition-Storage Funnel
Ace GlassPermits solutions to be prepared with No. 13654-24 Stirring Magnet and added portion wise. The T-bore stopcock in the equalizing arm permits isolation of the contents for storage. Capacity, 100 or 250mL. Lower threaded stopcock is all PTFE. Outer joint is standard taper 14/20 or 24/25, inner joint…
-
Funnel, Filter, Buchner
Ace GlassBuchner filter funnel featuring a standard taper, drip-tip bottom joint and a vacuum source hose connection. Available in various sizes and porosities.
-
Funnel, Addition, with Jacket
Ace GlassDouble scale graduated funnel with jacket for cooling with dry ice. Calibrated from stopcock. With 1:5 PTFE stopcock plug; for extra plugs, see 8224. For stoppers, order 8250-12.
-
Threaded stopcock with PTFE plug permits smooth needle valve adjustment down to 0.1cc/min. flow rate. Double PTFE ring seals prevent exposure of backup O-Ring to corrosive liquids. Angled position makes manipulation of stopcock easier than conventional style. 24/40 joints top and bottom, double…
-
With jacket for cooling or heating. All porosities of a given size are priced the same. Hose connection is size C.
-
Funnel, Addition, Pilot Size, Ace-Thred
Ace GlassLarge separatory funnel for use where large volumes are needed. Cylindrical shape necks down to a #25 Ace-Thred and connects to an 8mm bore PTFE-clad glass stopcock via a PTFE coupling using FETFE O-Rings. The system is completely grease-free. Complete
-
Funnel, Addition
Ace GlassWith an equalizing arm and a special stopper so that material may be isolated from the atmosphere. Turning the stopper completely closes the vessel to the equalizing arm so that the funnel may be disconnected without exposing contents to moist air, etc
-
Funnel, Liquid Addition, Offset
Ace GlassBorosilicate glass, liquid addition funnel with offset bottom joint Bottom standard taper joint with PTFE stopcock is offset to one side to accomodate space on crowded reactor heads, also allows for a larger funnel to be used. Top and bottom standard t
-
Similar to 9495, except lower stopcock is solid 1:5 PTFE metering valve, side arm plug is regular 1:5 solid PTFE. For replacement plugs, see 8232 or 8224.
-
Jacketed version of 7297 series addition funnels. Jacket runs from shoulder at top of vessel to above the PTFE stopcock. Has size D hose barbs for 3/8in ID tubing. Pressure equalizing arm runs from top of vessel to just below the PTFE stopcock. Graduat
-
With standard taper stopper joint. Stopcock available 1:5 PTFE plug. Stopper size is standard taper 24/40. For replacement stopcock plugs, see 8224. For stoppers, order 8250-12. Stopper NOT supplied.
-
Funnel, Pressure, Equalizing
Ace GlassCylindrical with standard taper joint top and bottom and drip stem. Stopcock has glass plug. Drip stem does not extend beyond joint, thereby eliminating possible source of breakage. For same funnel with 1:5 PTFE plug, see 9491.
-
Funnel, Pressure Equalizing
Ace GlassCylindrical with standard taper joint top and bottom and drip stem. Stopcock has glass plug. Drip stem does not extend beyond joint, age. Stopcock available with glass plug or 1:5 PTFE plug. thereby eliminating possible source of breakage. For same fun
-
Funnel, Pressure, Equalizing
Ace GlassCylindrical with standard taper joint top and bottom and drip stem. Stopcock has 1:5 PTFE plug. Drip stem does not extend beyond joint, thereby eliminating possible source of breakage. For same funnel with glass plug, see 9490.
-
Funnel, Pressure Equalizing, Graduated
Ace GlassCylindrical wtih standard taper joint top and bottom, drip stem, pressure equalizing arm and double scale graduations, calibrated from stopcock. Drip stem does not extend beyond joint, thereby eliminating possible source of breakage. Stop cock availabl
-
With straight, open top and a 2mm bore 1:5 taper PTFE stopcock plug. Porosity A frit, 145-174 micron.
-
Funnel, Powder, Angled, Heavy Wall Glass
Ace GlassHeavy wall glass powder funnel. Angled to fit in multi-neck flasks and reactor heads. Standard taper inner bottom joint.
-
Funnel, Powder
Ace GlassUseful in pouring powders or liquids into ground joint containers. Available with standard taper or spherical inner joint. Funnels without joints listed under 7242.
-
Funnel, Addition, Graduated
Ace GlassGraduated addition funnel featuring standard taper joints,graduations in both ascending and descending volume,protected drip tip and a glass stopcock. Graduations are calibrated from the stopcock.
-
For use with ACE Pressure Reactors. Heavy wall funnel has a #15 Ace-Thred at top that can be stoppered using 5846 Plug, not supplied. Bottom drip tip is long enough to be secured in the #15 Ace-Thred on 6433 Reactor Head or One-Piece Reactor and has a bump and groove that restricts blowout when…
-
Cylindrical with standard taper joint at top and bottom and drip stem. Stopcock on equalizing arm permits filling funnel without having to open the system to atmosphere. For replacement stopcock plugs, see 8224. For stoppers, order 8250-12 or 8255-10.
-
Funnel, Separatory, PTFE Plug
Ace GlassSeparatory funnel features a PTFE stopcock and a standard taper joint with drip tip. Stopper is not included.
-
Distilling Head, Magnetic
Ace GlassMagnetically operated swinging funnel type, with iron slug totally enclosed.This head maintains reflux ratio constant with changing throughput. The vapor bypass is designed to give accurate thermometer readings. Tapered bulb condenser increases capacity without choking. Side arm joint is…
-
Funnel, Pressure Equalizing
Ace GlassCylindrical with 24/40 standard taper joints top and bottom and drip stem. Stopcock has 1:5 PTFE plug. Drip stem does not extend beyond joint, thereby eliminating possible source of breakage. For same funnel with glass plug, see 7291.