Polypropylene racks snap together for easy assembly, sturdy construction, stackable, and are available in four colors. Will not float in waterbath. Alphanumerical positions for clear sample identification. Wide spaces between positions. Operating temperature -20 to 90°C. Autoclavable at 121°C.

Constructed of a special blend of polypropylene, these autoclavable racks will sink in a water bath Interlocking feet allow racks to be stacked while not in use Racks feature end plates for labeling. Rows are numbered and lettered for tube identification. Outside dimensions: 9.7” x…

Stainless steel racks are constructed entirely of rugged, corrosion-resistant 304 stainless steel. Highly polished surfaces reduce porosity and reinforce the corrosion-resistant properties.

Autoclavable Consists of an array of pegs spaced to hold tubes while allowing full view of contents Pegs convenient for holding inverted tubes for drying When racks are inverted, ribs keep tubes off base to allow drainage through holes 9260B01 and B13 are 13 mm with an array of 8 x…

One-piece molded racks have a three-tier grid design. Polypropylene construction provides good chemical and thermal resistance. Autoclavable. Racks feature a 3/4" x 2-3/4" labeling area on two sides. Open design allows easy viewing of contents from all sides.Available in sizes that hold 13mm or…

Ready-to-use No assembly required Provides an unrestricted view of tubes Available in 2 sizes: 13 and 16 mm and four colors: white, blue, green and red. Do not autoclave.

Made of acetal polymer A newly designed tube support that can be used all around the lab. The MultiRackTM is available in three models to accommodate a full range of laboratory test tubes and centrifuge tubes up to 30 mm in diameter. Although it is one of the most attractive racks available…

Polypropylene racks with a three-tier design provide a clear view of the tube contents and convenient insertion and removal of tubes. Racks are packaged unassembled and easily snap into place.  Available in mutiple configurations. 77706 - 13mm x 31 Tubes 77707 - 16mm x 31 Tubes …

Test Tube Supports for 10, 13, 16 mm tubes. Acrylic units have clear shelves with white sides and bases.

Compact size polypropylene plastic racks save space in water baths, laminar flow hoods and fume hoods. Available in 5 grid sizes to accommodate the full range of laboratory test tubes Steam autoclavable at 121°C (250°F) Dimensions: 12.8 x 10.5 x 7.2cmH (5.1 x 4.1 x 2.8")

Economical yet very durable racks that are submersible, autoclavable, and easily stack when empty.  Made from a special blend of polypropylene (PP) that makes them sink in a water bath and maintain their stability, even in agitated water.  The top tier features an alphanumeric grid…

Smooth finish leaves fewer places for contaminants to lodge; no welds to break, no sharp edges. Endplates accept large labels for easy identification of samples. Higher specific gravity than water so it stays submerged in a water bath and won't float. Withstands most lab chemicals and…

Constructed with Thermo Scientific™ Resmer™ Manufacturing Technology. Racks are repeatedly autoclavable. Smooth finish leaves fewer places for contaminants to lodge; no welds to break, no sharp edges. Endplates accept large labels. Rack withstands most lab chemicals and…

These RFID enabled racks specific for Captrack™ come pre-assembled with a unique RFID disk. After processing your samples with CapTrack™ these racks will allow the user to easily track their specimens to the appropriate cold storage location for fast and easy recall. These fully…

Fully autoclavable Molded from reinforced nylon for strength and durability with no coatings to chip, peel, or rust Single piece, three tier grid design for secure and stable racking of tubes Good temperature and chemical resistance to withstand a variety of lab procedures Large, flat…

Fully autoclavable Manufactured from durable reinforced polypropylene (PP) Three tiered design holds tubes securely Sturdy handles facilitate easy transport 4 Color options for organization of samples or benchtop

Fully autoclavable Manufactured from durable reinforced polypropylene (PP) Peg design allows easy viewing of tube contents Can be used to dry inverted tubes while minimizing collection of airborne contaminants Dimensions (L x W x H): 13mm: 179 x 127 x 64mm (7" x 5" x…