Corning PYREX

Graduated Capacity 5 mL in 0.1 mL divisions, with conical tip and Standard Taper 9 ground glass stopper, Thomas number 8770J22 Length including stopper, 140 mm; o.d. 13.5 mm

These 40mL capacity PYREX® homogenizers are designed for grinding small samples for pathological and biochemical work. The catch basin bulb has a 55mm outer diameter. Made in accordance with Federal Specification DD-T-363a. It may be used manually but is adaptable for use with a slow speed...

Color-coded Calibrated “to deliver” Graduated PYREX pipets are designed for cotton plugging. The uniform top-end openings permit performing of plugs and allow precise control of liquid column. Color-coded by size for easy identification and sorting. Colored graduations in 0.1 mL...

These flat, clear PYREX® dish covers will withstand repeated sterilization (wet or dry). Approximate dish cover diameter and height is 100x15mm. The edges are beaded to provide greater mechanical strength. The bead also provides a means to equally space t

Four sizes Borosilicate glass Wet or dry sterilization These PYREX roller bottles are available in four cell growth areas: 840, 1170, 1330 and 1585 cm 2 . Roller bottles are manufactured from borosilicate glass for the strength to withstand repeated wet or dry sterilization as well as optical...

These 250mL PYREX(r) low actinic flat bottom boiling flasks have full length outer 24/40 Standard Taper joints, but with shorter necks. Low actinic stained glass provides protection for materials sensitive to light. The protective color is an integral part of the flask, which retains the mechanical...

The PYREX® distilling condenser has 19/22 Standard Taper inner and outer joints, is simple in design and easy to use. Side tubulations are 10mm O.D. Distilling condensers are widely used in the lab, especially for fractionation. This condenser is also a replacement for organic chemistry kit No....

Available with 200 or 300 mm long heavy-wall outer jackets PYREX® West condensers are designed with a heavy-wall outer jacket to provide a sturdy, long-lasting unit, while the inner tube has a thinner wall for efficient heat transfer. The tubulations are on the same side to reduce breakage. The...

Narrow mouth PYREX® with glass stopper With ground neck With ground glass stoppers 125 mL and 250 mL bottles are furnished with a number 19 Standard Taper stopper; 500 mL bottles are furnished with a number 24 Standard Taper stopper; 1,000 mL and 2,000 mL bottles are furnished with a number 29...

Low actinic stained glass provides protection for materials sensitive to light. The protective color is an integral part of the flask, which retains the mechanical strength, chemical stability and thermal resistance of PYREX brand hardware.

These 125mL PYREX® cylindrical separatory funnels are graduated to show approximate capacity, The PTFE plug fits into the micro-finish barrel. The plug also reduces freezing problems and grease contamination.

These 50mL PYREX® conical centrifuge tubes have white enamel graduations and are graduated upward from tip to 10mL in 0.5mL divisions, and from 10 to 50 in 1mL divisions. The No. 16 Standard Taper pennyhead stopper is solid glass.

For aseptic filling of vessels Rubber tubing is attached to the top of the tubulation while the receiving vessel is placed inside the bell.

These PYREX(r) 250mL volumetric flasks provide improved lab convenience, broad selection and precise volume measurement. The strength of these flasks has been increased appreciably through machine-blown bodies to which are sealed heavy-tubing necks tooled

These 25x165mm PYREX® melting point tubes have a modified design to increase the rate of circulation.

Long and short stem funnels are ideal for filtering Molded to an accurate 60° angle for ease in fitting filter paper Beaded rim for mechanical strength Long stem, which is constructed of heavy wall tubing Molded to an exact 58° angle , which increases filtering speed High resistance to chemical...

Designed specially for handling and storing sterile culture media and sera where stability of the glass is of prime importance. Serum bottles are also suitable for storing distilled water and standard solutions. PYREX bottles have the strength to withstand hot air (dry) or steam (wet)...

Top edge is grounded flat within 0.25 mm to permit seal with flat cover Of PYREX borosilicate glass Without covers. Capacity and dimensions (L x W x D, mm) are given in listings.

These Drying Tubes are replacement parts for the 6949M series of PYREX® microchemistry kits.

This 1L PYREX® extractor body has a 45/50 Standard Taper outer top joint, a middle 35/25 Spherical Joint ball joint and a bottom 18/9 Spherical Joint socket joint. It is a component of the modular Continuous Heavier than Water Liquid/Liquid Extractor (Nos. 3922-M and 3924-M) and...

Calibrated to Class A ASTM E-542 and E-288 Supplied with a certificate of identification Traceable to NIST standards The graduation line is sharp and permanent. Large white block letters make it easy to read. Supplied with a Standard Taper stopper.

This 47mm fritted all-glass support base with tubulation is designed for assembly with either the 300 mL graduated glass funnel Cat. No. 33971-300 or 1000 mL graduated glass funnel Cat. No. 33971-1L. Disclaimer: This product is not intended to mitigate the presence of microorganisms on surfaces or...

Standard Taper 10/30 thermometer opening, distilling, three-way, Standard Taper joints Sidearm is at an angle approximately 75° from the lower part of the vertical tube The joint on the sidearm is at an angle approximately 105° from the sidearm The sidearm and lower tube are equipped with...

Transparent, permitting use on colored background, with shallow, concave wells 9 well plate is 85 x 100 mm; wells are 22 mm o.d. x 7 mm deep