Labconco

Fast-Freeze Flasks attach with adapters to valve ports on Labconco Drying Chambers and Manifolds. A complete Fast-Freeze Flask consists a rubber top, glass bottom and a supply of filter paper. Tops, bottoms and filter paper are available separately as replacement components. Adapters are available...

Canister W/Stand For Chem Trap

The Protector Downdraft Powder Station keeps users safe by containing powders during fi ngerprint processing. The open-sided, open-top work station provides unrestricted operator movement and accommodates oversized evidence. Available in 2' and 3' widths, two or more Stations may be placed...

Solvent Vent Kit

Blue anodized aluminum blocks hold tubes of various sizes in an aluminum bead bath Aluminum construction promotes the conduction of heat or cold from the Temp-Zone area to help maintain sample temperature Beads sold separately

Protector Stainless Steel Double Controlled Atmosphere Glove Boxes Protector Controlled Atmosphere Glove Boxes provide a leak-tight environment to perform work with contamination-sensitive materials under vacuum or in an inert environment. Fiberglass-lined models are performance tested to maintain...

Rodent Barricade

Solid Epoxy Dished Work Surfaces are available in 2', 3', 4', 5' and 6' widths. They may be used to support a variety of Labconco enclosures including Paramount Ductless Enclosures, Purifier Class I Enclosures, Purifier HEPA Filtered Enclosures, Purifier Filtered PCR Enclosures,...

Protector Pass-Through Laboratory Hoods offer sashes on two sides allowing operation on either side of the fume hood. An audible alarm sounds to prevent simultaneous opening of both sashes. With unobstructed visibility from either side, this hood is ideal for conducting chemistry demonstrations. An...

Rotary Vane Vacuum Pump, 195 liters/minute displacement at 60 Hz. 1.3 x 10-4 mBar partial pressure. Direct-drive, two-stage, oil-sealed, sliding-vane. Includes on/off switch, inlet and outlet ports, mode selector (High Vacuum and High Throughput), gas-ballast control (Closed, Low Flow and High Flow)...

Compact, corrosion-resistant housing Inherently safe design An accessory for the Demonstration Hood, XPert Balance Enclosure, Protector® XVS Ventilation Station or Protector® Work Station, the FilterMate uses a HEPA filter, carbon-based filter or a combination of both filters to remove...

Fully assembled from 18 gauge, 1 inch square steel tubing 4 inch diameter casters which absorb vibration over rough, uneven floors. Two have toe-locks. Two or four wire basket racks Includes removable drip pan Ergonomic, extruded rubber handle grips Lightweight, vinyl-coated portable wire baskets...

Use the Sash-Glider to clean both sides of a biological safety cabinet's sash while it remains closed, to avoid contamination risks. Kit includes: magnetic outside and inside blades 2 microfiber sheets 10 disposable white scrubbing strips Applicable Products: PuriCare Procedure Stations (2013...

HEPA Filters are suitable for removing 0.3 micron particulates. 99.99% efficient Color-coded purple Flow Type: Exhaust Application: Particulate

Guardian™ Digital Airflow Monitor senses and alerts the operator to low airflow conditions. LCD displays actual airflow in fpm or m/sec. Audible/visual alarm alerts the user to sustained low velocity condition. Calibration instructions displayed on LCD. Each monitor also includes a...

Blue anodized aluminum blocks hold tubes upright and promote conduction of heat or cold from the Temp-Zone area on selected models of Purifier Cell Logic Biosafety Cabinets to help maintain sample temperature. Holds 96 each 1.5 ml microcentrifuge tubes, 10.5 mm in diameter

SpillStopper Work Surfaces are molded from a special formulation of corrosion-resistant epoxy resins. They are dished and contoured to conform to the interior liner of Protector Laboratory Hoods. The front edge has a large radius to aerodynamically direct airflow into the fume hood. Pre-drilled...

Kit includes copper tubing, brass valve and black knob/connector. Max. flow rate of 0.5 LBM/min. Max. working pressure of 40 psi. Kits mount on the right or left side of any Protector Premier, XStream, XL, XLE or PVC Hood. Each kit includes one remotely-controlled service fixture with valve and...