Restek GC Equipment & Instruments
-
High-Capacity Moisture Trap
RestekPurged with ultra-high-purity helium; ready to use with any carrier gas including hydrogen Reduces water to less than 15 ppb Maximum operating pressure: 250 psi (1,724 kPa) Maximum flow: 1.25 L/min
-
Use for providing carrier, fuel, make-up, or auxiliary gases to laboratory instruments.
-
Valco fittings have been designed for the specific demands of instrumentation and manufactured with the tight tolerances and premium quality that analysts require. Connect two sizes of tubing, using zero-dead-volume fittings on each end. For 1/8" to 1/16" OD tubing. Stainless steel…
-
Restek Filter Base Plates
RestekEnd fittings available in brass or stainless steel Base plates fit all stand alone Super Clean gas filters offered Each single-position base plate unit measures: 4" x 4" x 1 7/8" (10.2 x 10.2 x 4.8 cm) Each 2-position base plate unit measures: 8" x 4" x 1 7/8"…
-
-
Fuel-grade high purity hydrogen generators are safer alternatives to high-pressure gas cylinders. The new Proton Exchange Membrane (PEM) cell eliminates the use of liquid electrolytes with hydrogen generators. Deionized water is all that is required to generate hydrogen for weeks of continuous…
-
Meets or exceeds original manufacturer's performance.
-
Valco fittings have been designed for the specific demands of instrumentation and manufactured with the tight tolerances and premium quality that analysts require.
-
CGA Fittings
RestekCGA-specified nuts and nipples with internal frit, 1/4-inch NPT nickel-plated brass.
-
-
Molecular Sieve S-Trap
RestekTraps water vapor; increases column and oxygen trap lifetime Reduces baseline noise from sensitive detectors such as ECDs and mass spectrometers Activated and ready to use Reduces water to less than 1 ppm Maximum flow: 1 L/min
-
Pocket Magnifier
RestekSmall and easy to handle 10x magnification makes it easy to see the column end to verify a square cut
-
Needle guide allows easy penetration and prevents septum coring Manual injection septum nut allows use of 26-gauge needles for on-column injections Made of high-quality stainless steel
-
Excellent thermal stability at injection port temperatures up to 450°C!
-
Rethreading Tool
RestekRepeated installation, removal, and temperature changes cause wear and damage to threads on GC parts. This can cause a poor seal, and oxygen can enter the system, compromising analytical results and possibly destroying expensive analytical columns. Repair worn or damaged threads Multiple…
-
-
Use with FID, TCD, NPD, and split/splitless inlets. Meets or exceeds original manufacturer’s performance.
-
Reduces the release of hazardous materials from the capillary split vent into the lab Includes connecting lines and mounting kit
-
Restek’s electronic maintenance indicator is a monitoring device that warns you when planned maintenance for a gas filter is due. Simply attach it to the consumable that you would like to monitor and the device will progressively display real-time filter status, allowing analysts to follow a…
-
Parker Female Connectors
RestekParker’s (A-Lok) fittings are ideal for installing new equipment, modifying existing instrumentation, or replacing worn connections. Fittings are available in brass and stainless steel. Siltek/Sulfinert treated or Silcosteel-CR treated fittings are also available. If there is a particular…
-
On-column injections can be performed only with 0.53 mm ID columns because 26-gauge needles do not fit into the bore of 0.32 mm ID columns, or into the Unliner liner taper. Reduces solvent tailing Versatile—0.53 mm ID version can be used in the direct (DI) or on-column (OC) injection…
-
Treated Hydroguard Deactivated Stainless Steel Tubing Hydroguard deactivation creates a high-density surface that is not readily attacked by aggressive hydrolysis. 304 Grade Stainless Steel and Seamless 316L Stainless Steel—Maximum continuous lengths are: 2,000 ft (1/16" OD),…