Gas Chromatography

Compare Tool

Select up to 3 products

HomeAll Products

Restek Gas Chromatography

1 - 32 of 534
Sort
View
Show
  • 1/16" Tubing Cutter

    Restek

    Produces square, smooth cuts in 1/16-inch tubing Eliminates tubing distortion Cuts hard or soft copper, aluminum, brass, stainless steel, Monel alloy, or titanium Replaceable cutting wheel

  • Vial Rack for Headspace Vials

    Restek

    Securely holds up to 36 headspace vials (fits 6, 10, or 20 mL vials). Vials lock in rack for convenient one-handed cap removal. Openings in the bottom of each well facilitate drainage. Alphanumeric indexing on rack simplifies sample identification. Easy to clean and fully autoclavable.*…

  • Restek ProFLOW 6000 Electronic Flowmeter

    Restek

    Flowmeters that can measure flammable gases are becoming mandatory due to the increased use of hydrogen in chromatography. With its Ex rating, the Restek ProFLOW 6000 meter is designed specifically with explosive and flammable gases in mind. The Restek ProFLOW 6000 is the only flowmeter you…

  • Dual Vespel Ring Inlet Seals for Agilent GCs

    Restek

    Our patented dual Vespel ring inlet seal greatly improves injection port performance—it stays sealed, even after repeated temperature cycles, without retightening the reducing nut! This seal features two soft Vespel rings, one embedded in its top surface and the other embedded in its bottom…

  • Electronic Rechargeable Crimpers and Decappers

    Restek

    These electronic crimpers and decappers have a rechargeable 6.4-volt battery installed. The large battery allows for quick, powerful operation and a faster charge cycle, minimizing downtime. Charging the battery takes thirty minutes to two hours. The universal plug set includes U.S., European, UK,…

  • Helium-Specific Super Clean Filter and Kit

    Restek

    Specifically designed for purification of helium in GC-MS systems Traps are packed and conditioned using helium Uses standard single-position base plate

  • Shortix Capillary GC Column Cutter

    Restek

    Consistently make precise, clean, square cuts with a diamond blade Built-in magnifier to verify square cut Use with 0.25 mm ID to 0.53 mm ID tubing (0.78 mm OD maximum)

  • Nylon Tube Brushes and Pipe Cleaner

    Restek

    Use to remove small septum fragments and residue from dirty glass inlet liners. Brushes are 1/8-, 3/16-, and 1/4-inch in diameter; pipe cleaner is one foot (30 cm) long.

  • Indicating Oxygen Trap

    Restek

    Indicator changes from light green to grey as oxygen is trapped Heavy-walled glass body, protected by polycarbonate sleeve, prevents oxygen and water infusion Prepurged for fast stabilization 100 psi (689 kPa) maximum operating pressure Reduces oxygen to 0.1 ppm 10 µm frits at…

  • 2.0 mL, 9 mm Short-Cap, Screw-Vial Closures (Polypropylene, preassembled)

    Restek

    Choose preslit caps (available for some vials) to reduce the risk of needle bending, release vacuum from high-volume injections, and improve injection reproducibility when greater than 20% of vial volume is withdrawn.

  • Straight Seamless 316L Grade Stainless Steel Tubing (Treated)

    Restek

    Treated Straight, 6-Foot Length Stainless Steel Tubing Individual 6-foot (± 1/2") straight pieces. In response to customer requests, we offer 6-foot straight lengths of 1/8-, 1/4, and 3/8-inch treated tubing. This tubing can be cut to your exact requirements using a standard tubing cutter.

  • 2.0mL Sample Vial Racks

    Restek

    Racks feature alphanumeric indexing for easier vial identification. Racks can be stacked for efficient storage. Fits most 2.0 mL, 12 x 32 mm vials (vials sold separately).

  • Rinsed and Cleaned 304 Stainless Steel Tubing

    Restek

    Use for providing carrier, fuel, make-up, or auxiliary gases to laboratory instruments.

  • MXT-Union Connector Kits for Connecting Metal and/or Fused Silica GC Columns

    Restek

    These MXT connectors can be used with fused silica tubing because of a Valcon polyimide, 1/32-inch, one-piece fused silica adaptor. This unique graphite-reinforced composite allows a capillary column to slide into the adaptor and be locked in place simply by loosening and tightening the fitting. …

  • Dynamic Duo (Restek Leak Detector and ProFLOW 6000 Flowmeter)

    Restek

    Protect your instrument and improve data quality with this powerful pair from Restek. Checking for leaks and verifying flows before you start helps you avoid costly problems later. Restek’s New Leak Detector Redesigned and better than ever, our new leak detector is an essential tool for…

  • Make Life Easier (MLE) Capillary Tool Kit for PerkinElmer GCs

    Restek

    Includes: 1/8", 3/16", and 1/4" nylon brushes 1/4", 3/8", and 3/16" stainless steel wire tube brushes Stainless steel surface brush 6 stainless steel jet reamers (0.25–0.65 mm OD) 1/4" x 5/16" open end wrench 3/8" x 7/16"…

  • Mininert Precision Sampling Valves for Vials

    Restek

    Mininert valves are very convenient for repetitive sampling and limit content exposure to the silicon septum. Models are available for screw-cap and crimp-top vials. The crimp-top valve for 20 mm ID glassware slides into the neck of the vial. Turn the threaded flange to secure a tight fit.

  • Capillary-Grade Hydrocarbon Trap

    Restek

    Packed with an extremely high surface area, baked coconut shell–based activated carbon Purged with ultra-high-purity helium; ready to use with any carrier gas including hydrogen Reduces organics to 0.1 ppm (assuming 100 ppm input) Maximum operating pressure: 250 psi (1,724 kPa)

  • Reducing Ferrules

    Restek

    Available in graphite or Vespel/graphite material. Graphite Ferrules Preconditioned to eliminate outgassing High-purity, high-density graphite Smoother surface and cleaner edges than conventional graphite ferrules Contain no binders that can off-gas or adsorb analytes Stable…

  • Replacement Needles for A-2 Luer Gas-Tight Syringes

    Restek

  • Oven Flapper Assemblies for Agilent 5890/6890 GCs

    Restek

    Ensure even and consistent column heating when the insulation becomes damaged or worn Replacement Insulation Gasket and Hardware Kit includes the insulation gasket, 2 screws and 2 nuts Meets or exceeds original manufacturer's performance Insulation is replaceable, using Restek's…

  • EZ No-Vent GC Column-Mass Spectrometer Connector for Agilent GCs with 5971/5972,…

    Restek

    We designed the EZ No-Vent GC column-mass spectrometer connector to be simple and easy to use. A critical orifice in the EZ No-Vent connector minimizes the amount of oxygen allowed into the MS source, eliminating the need for purge gas as is required for other manufacturers' vent systems. This…

  • Parker Balston Zero Air Generators

    Restek

    Turn in-house compressed air into ultra-pure air (<0.1 ppm total hydrocarbons) Remove hydrocarbons to less than 0.1 ppm by catalytic oxidation Operate at 40–125 psi (276–862 kPa) Typical payback is less than one year, based on cylinder costs Install easily and take up…

  • Restek Electronic Leak Detector

    Restek

    Don't let a small leak turn into a costly repair—protect your analytical column by using a Restek leak detector. Backed by a one-year warranty, the Restek leak detector is the industry standard for performance and affordability in handheld leak detectors. Features & benefits…

  • Methane Cylinder Kit

    Restek

    Setting the column flow rate by injecting methane and optimizing linear velocity is a preferred method for establishing reproducible retention times (ASTM Method E1510-93). The kit includes a Scotty 14 cylinder containing 1% methane in helium, a MINICYL regulator, a syringe adaptor, and a package…

  • Refillable Hydrocarbon Trap

    Restek

    Removes trace impurities from carrier gas Reduces organics to 0.1 ppm (assuming 100 ppm input) 60 µm frit prevents gas contamination by purifier particles Good for purge-and-trap systems Refillable and rechargeable Maximum operating pressure: 125 psig (862 kPa) Maximum flow:…

  • Coiled 316L Grade Stainless Steel Tubing (Treated)

    Restek

    Treated Seamless 316L Grade Stainless Steel Tubing High durability tubing. Recommended for: Inert applications High temperatures High pressures Corrosive environments Zero bleed

  • Micro-Vials with Screw Threads

    Restek

    Tapered for high recovery of contents Work with Mininert sampling valves

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.