Rod Clamp

Compare Tool

Select up to 3 products

Rod Clamp
1 - 32 of 239
Sort
View
Show
  • Large Rod "Muff" Clamps

    Humboldt

    These Rod Clamps are otherwise known as the "muff" portion only and can be used to create custom clamps to satisfy a wide range clamping applications.

  • Rod "Muff" Clamps

    Humboldt

    These Rod Clamps are otherwise known as the "muff" portion only and can be used to create custom clamps to satisfy a wide range clamping applications.

  • Swivel Clamp Holder

    Humboldt

    For attaching extension clamps to supports Aluminum construction Has swivel for rods up to 5/8” diameter

  • Threaded Base Plates

    Humboldt

    …to a tabletop or inverted into a recessed hole for flush mounting. Models are available with either a threaded hole completely through the center or with an unthreaded thru-hole. These die-cast units are supplied without rod. Other sizes are available on request with threaded or straight holes.

  • Labjaws Aluminum Frame Rods

    Troemner

    Centerless ground for precision fit and chamfered ends for easy assembly. Hard tempered surface is corrosion resistant and has a melting point of 1100 °F. 13 mm diameter rods are available up to 244 cm long.

  • Stainless Steel Closed Lab Rod Connector

    Lee Engineering

    Accommodates (1/2") rod. Locked with 14"-20 hex screws.

  • Burette Clamp

    United Scientific Supplies

    This clamp features plastic coverd spring jaws. Accepts burettes up to 35mm OD, and support rods up to 0.5" OD. Available as a single or double burette clamp.

  • SYNTHWARE Thermometer Clamp

    Kemtech America

    Thermometer Clamp, Synthware, Extension Rod Diameter: 10mm, Overall length: 200mm.

  • Ultra Clamps

    Ohaus

    Strong Aluminum Alloy Fitted with Over-sized knobs Rods supported on 4 inch long surface to avoid vibration and wobble

  • Labjaws Connectors and Mounting Brackets

    Ohaus

    Rod End Connector (2824E29) Holds rods firmly at 90°. Use when semi-permanent installations are required. Comes with two set screws and is precision bored for close fit. S-Connector (2824E33) Clamps lab frame rods at 90° angle. Twin angled screws allow independent rod

  • Support Stand Clamps

    Ohaus

    … Accommodates 1/2 inch to 5/8 inch diameter shaft of Talboys motor support and rod of 8596B10 support stand Stainless Steel Construction Strong aluminum alloy with a brushed finish and large knobs facilitate easy tightening Rods supported on 4 inch long surface to avoid vibration and wobble

  • Clamp and Support Rods

    Humboldt

    Designed to allow users to mount rod vertically or horizontally. The clamp is cast iron with a black enamel finish. Supplied complete with a 3/8" x 20" (10mm x 508mm) rod (H-21350) or a 1/2" x 24" (13mm x 610mm) rod (H-21360).

  • Pendulum Clamp

    Humboldt

    This unit clamps to any horizontal or vertical support rod up to 3/4" (19mm) in diameter. The clamp is designed to hold three pendulums spaced 2-1/8" (54mm) apart with points for suspending cords on the same horizontal line, each individually adjustable. The overall length is 10-1/2" (267mm) by 3/4"…

  • Table Clamp

    Humboldt

    The Table Clamp is designed to support meter sticks and other round or square rods, either vertically or horizontally up to 1" (25mm) thick. The Vee's are milled at right angles and the clamp can be mounted on table edges up to 1-3/4" (45mm) thick. Each jaw can be adjusted separately. Heavy cast…

  • 3-Prong Heavy Duty Extension Clamp

    United Scientific Supplies

    This extension clamp features heavy-duty electroplated zinc alloy construction and dual prong adjustments. The 5" long extension rod is constructed of stainless steel Prongs open to about 4", have a recommended maximum grip size of about 3.25", and feature double keyed…

  • Conical Flange Vessel Clamp

    Wilmad LabGlass

    This clamp is designed for reaction vessels/kettles with a conical flange. The top clamp is easily removed without disturbing the cover or body of reaction flask. Disassemble by loosening nuts. Includes extension rod for clamping to a laboratory stand. NOTE: Use with LG-8010 to LG-8050 vessels…

  • Universal U-Shaped Support Base And Rod

    Eberbach

    …No. 7560 - 3/4" dia x 34" L 2 section nickel-plated steel support is mounted in iron base Base has 5 threaded holes for convenient rod placement Breaks down into compact unit Package size 18-1/2" x 4" x 2" Larger bases available, call for details Units…

  • Clamp, Lattice

    Harvard Apparatus

    Of glass-filled nylon Has two open sides which take (and lock in place, at right angles) rods up to 1/2” (13mm) diameter Locking screws are M5 (5 mm) thread Allen set screws 1/2” (13 mm) long; without rod

  • Clamp and Support Rod

    Humboldt

    Highly versatile, the rod height can be locked into any position by a simple thumbscrew located on the outer edge of the clamp. The clamp features a sturdy handle for tightening the unit on the edge of a table top up to 1-1/2" (38mm) thick. The plated, solid steel rod is 1/2" (13mm) in diameter by…

  • Talboys Support Rod and Clamp Kit

    Troemner

    …for holding temperature probes, thermometers or other glass tubes. Includes an 18" (45.7cm) aluminum support rod, thermometer/temperature probe extension clamp, 3-prong medium swivel clamp, and hook connector. Recommended for Professional, Advanced or Basic Hotplates or Hotplate-Stirrers.

  • Stronghold Support Glass-Filled Nylon Jaw Clamps

    Harvard Apparatus

    clamps have fixed screw action and open to 5/8” (16 mm), for thermometers, burets, rods, etc. Jaws close down to completely shut. 8847T02 clamp has extension stem 5” x 1/4” diameter (125 mm x 6.4 mm); 8847T04 Clamp has male connector; 8847T06 has ball joint adapter. Medium clamps

  • Swivel Clamp

    United Scientific Supplies

    Chrome plated steel double clamp. Accepts rods up to 0.75" (19mm) in diameter. One clamp can be rotated 360° about long axis and clamped in any position.

  • 4-Prong Extension Clamp

    United Scientific Supplies

    Features a 4-prong die-cast clamp attached to a chrome-plated steel rod. Jaws are lined with cork. Overall length is 8".

  • Rod Coupler, Stainless Steel

    Lee Engineering

    Extend the length of your lab frame rods. This strong, corrosion-resistant aluminum alloy connector permits end-to-end joining of 12.7 cm rods in diameter. Precision machining ensures rod alignment. Comes with two tee handles for adjustment.

  • Rod Arms for Clamps

    Troemner

  • Clamp, Rod mounted, Swing Latch

    Ace Glass

    Bolt latch clamp secures the top of Scale-Up Series™ reaction flask to our stand.

  • Radleys Starfish Monifolds, Clamps and Support Rods

    Heidolph

    …The detachable Velcro straps allow the clamping of a wide range of glassware from 20 mm to 60 mm in diameter. Users have a choice of two support rods, both 12 mm in diameter: the 650 mm one-piece rod and the two-piece 650 mm split rod. The split rod has a threaded joint halfway along its body,…

  • Clamp Holders

    United Scientific Supplies

    Clamp holders for rods up to 19mm (0.75") in diameter. Available in Cast Iron or Brass.

  • Pendulum Clamp

    United Scientific Supplies

    Connect this clamp to any support rod and set up to three separate pendulum demonstrations. Includes individual cord clamps.

  • Universal Clamp

    GSC International, Inc.

    Both sides of the clamp have screw type fitting that allow you to lock release or tighten as needed. The boss head clamp can be used on a stand rod up to 1.9 cm in diameter.

  • Suspension Clamp

    Troemner

    …Price: $33.94 Holds thermometers, potash bulbs, drying tubes and other apparatus. Suspends item 10 cm from support rod. Integral post clamp accepts up to 21 mm diameter rod. * Sale price valid only on current stock. Additional units may be available for purchase at original price.…

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.