Heating And Stirring Mantles

Across International heating and stirring mantles come standard with digital display for the most accurate control. The large display interface makes it easy to quickly and precisely adjust temperature and rotation speeds. The DigiM mantle is equipped with two sets of thermocouples for proper…

…of stirring which widens the range of applications. Stirring operation is simply achieved by placing the correct size stir bar into the flask, turning the stir control to the minimum speed and ramping up slowly. If the magnetic coupling to the stir bar is lost for any reason, the stir speed…

Incorporates a stirring module that allows the solution to be stirred and heated at the same time Three positions for 100, 250, 500 or 1,000 mL flasks Designed to maximize safety Separate heating controls for each position Temperature range to 450°C Stirring speed: 50 to…

This series of analog heating mantles includes a built-in stirrer function. Separate knobs control the temperature level up to 400° C and stirring speed up to 800 rpm. Case is constructed of durable stainless steel and aluminum materials. Knitted mantle is made from glass fiber yarn and designed…

This series of digital heating mantles includes a built-in stirrer function. Separate knobs control the temperature level up to 400° C and stirring speed up to 800 rpm. The external probe allows the temperature of the contents of the flask to be directly measured. Case is constructed of durable…

…functionality of magnetic stirring. For convenience and safety, the electric circuitry for stirring is built into the base of the heater, enabling powerful stirring over a wide range of solution volumes and viscosities using a magnetic stir bar. Magnetic stirring Stirring operation is…

BriskHeat's All-in-one HM metal housed heating mantle with control and magnetic stirrer are fiberglass insulated round bottom flask heaters for laboratory and pilot laboratory applications. These heating mantles provide uniform heat distribution to a variety of round bottom shaped vessels, to either…

Economical and dependable. These mantles have a ceramic heat cavity (resistance wire completely embedded), a grounded metal housing for safer operation, a low profile that permits magnetic stirring, and can be operated at up to 550 C. May be used as an air or sand bath. All models have a 36 in.,…

Economical and dependable. These mantles have a ceramic heat cavity (resistance wire completely embedded), a grounded metal housing for safer operation, a low profile that permits magnetic stirring, and can be operated at up to 550 C. May be used as an air or sand bath. All models have a 36 in.,…

Economical and dependable. These mantles have a ceramic heat cavity (resistance wire completely embedded), a grounded metal housing for safer operation, a low profile that permits magnetic stirring, and can be operated at up to 550 C. May be used as an air or sand bath. All models have a 36 in.,…

…tubing with screw connectors. The heating mantle with stirrer features a polyurethane coated aluminum exterior and a high quality knitted mantle with glass fiber underlay for uniform distribution of heat. Maximum operating temperature is 400°C. Mantle can be used in a wide range of ambient…

…round bottom flask of 250ml, 500ml or 1000ml capacity to be stirred and heated up to an element temperature of 450°C through precise electronic control, giving an accurate measure of temperature and stirring. The modular design allows heating cartridges of different sizes to be interchanged using…

Used to control THERMOWELL heating mantles or other resistive heating circuits (hot plates, heat tapes, water baths, etc). Available in solid-state or proportional on/off models. All models are fused (without circuit breakers). Calibrated in terms of percent power level from 5 to 90% (i.e. when knob…

…Schlenk flask with a standard taper outer joint and a 0-4 mm high vacuum valve in the side arm. The valve has a PTFE o-ring at the tip. The Kjeldahl shape permits easy transfer of liquids and solids. The lower portion of the flasks fits standard heating mantles to facilitate heating and stirring.

SYNTHWARE modified Schlenk flask with a standard taper outer joint and 2mm bore glass stopcock in side arm. The Kjeldahl shape permits easy transfer of liquids and solids. The lower portion of the flasks fits standard heating mantles to facilitate heating and stirring.

SYNTHWARE modified Schlenk flask with a standard taper outer joint and a 2mm bore PTFE stopcock in side arm. The Kjeldahl shape permits easy transfer of liquids and solids. The lower portion of the flasks fits standard heating mantles to facilitate heating and stirring.

…outlet. Vessel top has a 25mm Ace-thred center neck and various multi-neck configurations. System is designed to perform positive pressure reactions at up to 45 psi at 100 degrees C. Included are a heating mantle and controller, stirring shaft and controller, addition funnel, condenser and manifold.

…a 100mm (4 in) head with (4) 24/40 joints, an allihn condenser, a pressure equalizing funnel, overhead glass stirring assembly with variable speed motor and controller, heating mantle with type J PTFE covered probe and controller. All wetted surfaces are glass or PTFE. A sturdy stand and all…

… Fine control of stirring speed; there is almost no variation; no speed increase in warming or slowdown in cooling Can be reproducibly set to any given speed; range 50 rpm to 740 rpm Two receptacles on back, which make it possible to use two stirring units at once "Synchrostart",…

…to heaters and, if applicable, supplied to stirrers Additional Features for Heater/Stirrer EMEA6 models Allow the solution to be stirred and heated simultaneously Provide stirring speeds of between 50 to 1000rpm One stirring control operates each set of three recesses

…for mantles with holes or very thin insulation that will accommodate separate stirring devices The optional EMC-4 StirControl II (Thomas number 5912M10) creates and synchronizes a rotating magnetic field within the StirMantle that drives the stir bar inside a flask Heating and stirring are…

…heat transfer and support Earth (ground) screen encloses the heater for added safety Individual heater cartridges are replaceable Neon lights indicate when power is on and supplied to heaters and stirrers. Allow the solution to be stirred and heated simultaneously Provide stirring…

…heat transfer and support Earth (ground) screen encloses the heater for added safety Individual heater cartridges are replaceable Neon lights indicate when power is on and supplied to heaters and stirrers. Allow the solution to be stirred and heated simultaneously Provide stirring…

…heat transfer and support Earth (ground) screen encloses the heater for added safety Individual heater cartridges are replaceable Neon lights indicate when power is on and supplied to heaters and stirrers. Allow the solution to be stirred and heated simultaneously Provide stirring…

…way to heat and stir a round bottom flask from 10 ml to 5 liters. Replace messy oil baths, heating mantles, avoid spills and make your chemistry safer, cleaner and faster It is accepted that oil baths and heating mantles are no longer the preferred choice of chemists to heat round bottom…

Rugged cylindrical flask with neck opening of 4" with side indents for improved stirring characteristics. Uses 6496 clamp for securing flask head. For use with 6478 heating mantles.

Kjeldahl shape facilitates heating and stirring while permitting easy transfer of liquids or solids. Lower portion of flask fits standard heating mantles. Available with a choice of a 2mm high vacuum glass stopcock having a S.S. constant pressure retaining device or a 0-4mm Chem-Cap®…

…flange. Indentations increase agitation of the contents of the vessel during stirring. Flange is also ground to permit a greased seal with any of the lids CG-1940 through CG-1946. Vessel will fit standard heating mantles CG-10000 through CG-12502. For clamp see CG-141 or CG-141-T. For o-ring see…

… Features a modified Kjeldahl shape that facilitates heating, stirring and solvent stripping without impairing ease of liquid and solid transfer The bottom of the flask is shaped to fit Kontes oil spherical heating mantles. Standard Taper joint size for Thomas numbers 4955L93 through…