SP Bel-Art, test tube
-
Constructed of a special blend of polypropylene, these autoclavable racks will sink in a water bath Interlocking feet allow racks to be stacked while not in use Racks feature end plates for labeling. Rows are numbered and lettered for tube identification. Outside dimensions: 9.7” x…
-
Autoclavable Rows are numbered and lettered Base plate has rounded wells with drain holes. Molded cutouts in end panels form handles. 9259L10 and L20 are 213 x 110 x 111 mm high; 9259L30 through L50 are 213 x 110 x 127 mm high.
-
Scienceware® No-Wire™ Test Tube Racks
SP Bel-ArtGreat alternative to wire racks Stackable Available for 6 standard tube diameters Available in 3 colors Dimensions: 246mm x 104mm x 64mm high (9.7" x 4.1" x 2.5") Autoclavable at 121°C (250°F) Rugged racks are molded of autoclavable polypropylene. Footprint dimensions…
-
No-Wire Test Tube Grip Racks
SP Bel-ArtTest Tubes ‘Hang in There’ in Any Position, Even Inverted! Retainer fingers hold tubes firmly in the rack plates with no fear of dislodging, making them perfect for both decanting and water bath work. • Fingers allow simultaneous decanting to save valuable…
-
Poxygrid® "Half-Size" Test Tube Racks
SP Bel-ArtExcellent space-savers for use in water baths, laminar flow hoods, fume hoods or any place where space is limited. Choice of three colors: orange for biohazard warning, green and blue for general lab use. Chemical and corrosion-resistant steel wire racks are coated with heat-cured epoxy …
-
Bel-Art® Poxygrid Test Tube Racks
SP Bel-ArtChoice of Four Colors and Multiple Sizes Chemical and corrosion-resistant steel wire racks are coated with heat-cured epoxy. Orange racks can be used for biohazard warning, yellow for radioactive warning. Epoxy coatings are unaffected by organic solvents, salts, weak acids and weak…
-
Stack Rack® Test Tube Rack
SP Bel-ArtWells are numbered and lettered for simple tube identification. Steam autoclavable at 121°C (250°F) Made of polycarbonate; with crystal clear decks – perfect for submersing in a water bath Interlocking end plates for safe stacking when loaded with tubes up to 10cm (4")…
-
Bel-Art® Poxygrid Test Tube Racks
SP Bel-ArtChoice of Four Colors and Multiple Sizes Chemical and corrosion-resistant steel wire racks are coated with heat-cured epoxy. Orange racks can be used for biohazard warning, yellow for radioactive warning. Epoxy coatings are unaffected by organic solvents, salts, weak acids and weak…
-
Full-View Test Tube Supports
SP Bel-ArtHold More Tubes, Waste Less Space This versatile polypropylene rack has pins for supporting or draining test tubes. Stores test tubes upright, full or empty Holds inverted test tubes over pins for draining The rack with 102 pins, 5 x 16 rows (9259G50), is excellent for drying…
-
Switch-Grid™ Test Tube Racks
SP Bel-ArtThis innovative, split-frame rack holds up to two different size tubes in the same rack and allows users to quickly switch grids to hold other sizes as needed. Each rack frame includes a set of grids in one size. Grid sets in alternate sizes can be purchased separately. 10mm to 30mm…
-
Scienceware® No-Wire™ Test Tube Half Racks
SP Bel-ArtCompact size polypropylene plastic racks save space in water baths, laminar flow hoods and fume hoods. Available in 5 grid sizes to accommodate the full range of laboratory test tubes Steam autoclavable at 121°C (250°F) Dimensions: 12.8 x 10.5 x 7.2cmH (5.1 x 4.1 x 2.8")
-
Poxygrid® "Rack and a Half" Test Tube Racks
SP Bel-ArtFor High Volume Work High quality epoxy-coated wire racks in convenient extra-long sizes for volume test tube work. Epoxy coated steel wire is chemical and corrosion resistant Steam autoclavable at 121°C (250°F)
-
Scienceware® Stack Rack® Test Tube Racks
SP Bel-ArtMatch Rack Material to Lab Use These sturdy, rigid racks feature interlocking end plates with handles for secure stacking when loaded with tubes up to 10cm (4") long. Rows are numbered and lettered for easy tube identification. All racks are steam autoclavable at 121°C (250°F). …