Chemglass, Flasks, Supplies
-
Replacement vessel is supplied with black phenolic, rubber lined caps for the 18mm side arms, polypropylene caps and pouring rings for the GL-32 and GL-45 side arms.
-
Round bottom 2-neck flask having standard taper outer joints, both being of the same size. Available with a choice of a 2mm high vacuum glass stopcock having a S.S. constant pressure retaining device or a 0-4mm Chem-Cap® Airfree® inlet valve. Side neck can be fitted with a CG-3022 septum…
-
Round bottom, HEAVY WALL, four-neck flask with standard taper outer joints on the center neck and vertical side necks. The third neck is a 10/30 outer joint for use with a CG-3506, 10/30 jointed thermometer. Flasks with 29/26 center necks have a groove tooled just below the grind to aid in the…
-
Round bottom, HEAVY WALL single long neck flask with a standard taper outer joint.
-
Baffle indents on the lower outside edge of the flask to help oxygen transfer to the culture medium when used on an orbital shaker.
-
Round bottom, HEAVY WALL three neck flask with standard taper outer joints on the center neck and 20º angled side necks. Flasks with 29/26 center necks have a groove tooled just below the grind to aid in clamping of the flask.
-
Water jacketed, flat bottomed spinner flasks consist of a water jacketed spinner flask, manufactured from Type 1 Class A borosilicate glass, and a microcarrier style impeller with glass shaft that extends through the cap and PTFE paddle. Flasks are typically used with a circulating water bath.…
-
Round bottom, HEAVY WALL, four neck flask with standard taper outer joints on the center and vertical side necks.
-
Extra deep baffle indents on the lower outside edge of the flask to maximize oxygen transfer to the culture medium when used on an orbital shaker.
-
Heavy wall, wide mouth flask with a GL80 glass thread and a 24/40 connecting adapter. Flasks have a heavy wall for vacuum applications and are balanced to prevent run-out during rotation. Unique design makes it easier to handle highly viscous liquids, powders, and solids. The large opening permits…
-
Glassblowers Flask Blanks, Round Bottom
ChemglassBlanks for fabrication of single or multi-neck round bottom flasks. NECK IS UNFINISHED, FLASK CANNOT BE USED WITHOUT MODIFICATION OF NECK.
-
Flasks, Dewar, Low Form, Foam
ChemglassFeatures: Increased SAFETY- Unbreakable Lightweight Design Each Dewar is Supplied with a Lid Patented Closed Cell Foam Construction (USPTO # 7,971,744) Lower Boil Off and Consumption of Liquid Nitrogen Patented foam dewars provide a safe and durable vessel for handling…
-
-
Erlenmeyer Polycarbonate Sterile Flasks
ChemglassErlenmeyer flasks are sterile, non-pyrogenic and manufactured with polycarbonate resin. Flasks are supplied with exclusive DuoCap® designed for both aerobic and anaerobic applications. For aerobic applications the cap utilizes a 0.22µm pore size PTFE membrane for sterile air exchange.…
-
Extra deep baffle indents on the lower outside edge of the flask to maximize oxygen transfer to the culture medium when used on an orbital shaker. Delong style neck is made to fit stainless steel or plastic closures, while the longer neck reduces the amount of splashing that would reach the closure.
-
Round bottom storage flask with a standard taper outer joint on the sidearm. The 50, 100 and 250mL sizes have a 0-4mm Chem-Vac™ Chem-Cap® valve while the 500 and 1000mL sizes have a 0-8mm valve size.
-
ADAPTERS, CLAISEN, MINUM-WARE®, Useful for addition of reagents to moisture sensitive reactions. Lower inner and top outer threaded joints all are 14/10 size. Supplied complete with two open-top screw caps (MW-102-33), PTFE faced septa (MW-104-33) and Viton o-rings (MW-100-08). CONDENSERSS,…
-
Round bottom, HEAVY WALL single short neck flask with a standard taper outer joint. The 29/26 flasks have a groove tooled just below the grind to aid in clamping of the flask. Please note: There are separate listings for different capacity single neck round bottom flasks.
-
Round bottom, HEAVY WALL flask with a standard taper outer joint and a #7 Chem-Thread as a side neck for insertion of thermometers or bleed tubes having an O.D. between 4 and 7mm.
-
Spinner Flask
ChemglassWater jacketed, flat bottomed spinner flasks consist of a water jacketed spinner flask, manufactured from Type 1 Class A borosilicate glass. Flasks are typically used with a circulating water bath. Jacket volumes are approximate and flasks are not graduated. Note: Paddle and Cap assembly are…
-
Flask has 6 baffles, 3 baffles on the lower outside edge of the flask and 3 baffles on the bottom surface of the flask to maximize oxygen transfer to the culture medium when used on an orbital shaker. Gray polypropylene vented cap has a 0.22µm (PTFE) hydrophobic membrane to allow gas exchange…
-
Heavy Wall Blank Filter Flasks
ChemglassExtra heavy, unmarked blanks for fabrication of filter apparatus. Top has a tooled finish to accept a rubber stopper or neoprene filter adapter.
-
Round bottom, HEAVY WALL, five-neck flask with standard taper outer joints on the center neck and vertical side necks.
-
Flask has 4 bottom baffles and a constriction just below the neck to prevent splashing from reaching the closure.
-
Fernbach 2800mL 3 Side Baffles Flasks
ChemglassFlasks are designed for culturing organisms that require a large surface area to volume ratio. Flask has 3 baffles on lower outside edge to help oxygen transfer to the culture medium. Available with a plain 59mm ID neck, 38mm OD Delong style neck or GL-45 screw neck supplied with a vented cap.
-
Round bottom, HEAVY WALL, three-neck flask with standard taper outer joints on the center neck and vertical side necks. Lower half of the flask is jacketed with two hose connections for circulation of heating or cooling liquid.
-
Unbreakable Dewar flask is made entirely of Stainless Steel. Dewar flask has many flexible laboratory applications including cooling of small samples and as an insulating flask. Furthermore, it can be used for storage and transport of liquid nitrogen LN2, dry ice CO2, and…
-
MicroCarrier spinner flasks promote optimal growth of suspension and microcarrier cultures. Indented bottom (100mL thru 1000mL) prevents accumulation of microcarrier beads under the impeller paddle. The 3L version does not have a dimple. The complete system includes a flask with two angled sidearms…
-
Minum-Ware® Round Bottom 3-Neck Flasks
ChemglassMicro round bottom 3-neck flask with all 14/10 threaded outer joints. Supplied complete with open-top screw caps (MW-102-33) and Viton O-rings (MW-100-08).
-
Flask has 6 bottom baffles to maximize oxygen transfer for bacterial, yeast and other cultures that require large amounts of oxygen for optimal growth. The 70mm vented cap has a 0.20µm PVDF hydrophobic membrane to allow for sterile gas exchange while preventing contamination. A silicone liner…
-
Flasks, Erlenmeyer, Stopper Tops
ChemglassErlenmeyer flask with standard taper stopper top. Available with or without stopper. For stoppers only see CG-3018.
-
Flasks, Heavy Wall, Pear Shaped
ChemglassPear shape HEAVY WALL flask with a standard taper outer joint.