Ace Glass, Nucleic Acid Sample Preparation
-
Circulator Hose Support
Ace GlassAll stainless steel, fully adjustable clamps for securing and supporting circulator hoses used with jacketed pilot plants. The universal clamps adjust to any pipe style pilot plant stand, and the clip will accommodate any standard circulator hose size.
-
Condenser, Cold Finger
Ace GlassJacket length is measured from the lower shoulder of the bulb to the bottom of the finger. Diameter of tube is 14mm. Used in 6472 Pilot Plant Reactor.
-
Distilling Column, Jacketed
Ace GlassJacket length 250 mm, with indents for supporting glass beads or other packing.
-
Stainless steel, four post support stand for large scale chromatography columns. Each stand is designed to fit either 24", 48" or 72" length glass columns. Each stand has a PTFE collar at the bottom and an adjustable stainless steel collar at the top to support the column. All stands have locking…
-
Condenser, Allihn
Ace GlassBulb type, approximately one bulb per 50 mm, with 24/40 standard taper inner joint at bottom.
-
Condenser, West
Ace GlassWith top joint jacketed for water cooling. Jacket length measured from bottom of top joint.
-
Powerstat Mounting Bracket
Ace GlassMounting bracket permits easy and convenient mounting of 12080 or 12081 Powerstats on standard laboratory racks or stands having up to 16mm O.D. rods. Made of strong, rust and corrosion resistant aluminum alloys. Bracket is attached to the bottom of the powerstat by two screws and to the rack or…
-
Column, Chromatography
Ace GlassWith 24/40 standard taper joint at top and a 2 mm bore stopcock at the bottom.
-
Distilling Column
Ace GlassVacuum jacketed and silvered with observation stripe. Also available unsilvered. With an enlarged bulb knockdown section that removes high boiling ends without choking. Length of packing section is 100 or 200mm, I.D. approximately 10mm. With indents to
-
Rapid Preparative Chromatography System
Ace GlassRapid preparative chromatography system suitable for use to pressures of 50 psig, operation behind a shield is recommended. Resevoir is 2L or 3L capacity, epoxy coated and pressure tested. Complete item includes:Brass or glass manifold, pressure gauge, pressure relief valve, column, tubing, and…
-
Support Ring, Solid PTFE
Ace GlassUseful for supporting column, flasks, dishes, etc. Shaped with internal bevel.
-
Clamp, Rod mounted, Swing Latch
Ace GlassBolt latch clamp secures the top of Scale-Up Series™ reaction flask to our stand.
-
Micro cold finger condenser with drip tip on bottom for directing drops into the well of 14/10 jointed 9576 or 9599 Hickman Stills. Cold water is introduced into cold finger periodically by means of a Pasteur pipet. Complete item consists of cold finger condenser and multi- purpose vacuum adapter…
-
Condenser, Allihn
Ace GlassBulb type, approximately one bulb per 50 mm, with various joint sizes at bottom and top. Available with hose barbs or Ace-Safe connectors.,/p>
-
Support Stand, Kilo Scale Reactors
Ace GlassThomas No. 1165L75, 1165L76, 1165L77, 1165L78, 1165L79, 1165L80 Redesigned, modular Kilo scale reactor support stand Thomas No. 1165L81 Bracing set to further strengthen the Universal Stand²against the weight of our explosion proof motor. Set²consists of two braces. …
-
Replacement condenser for Buchi rotary evaporators. Available plain or safety coated. Includes PTFE hose barbs,GL caps and plug.
-
Distilling Column, Plain
Ace GlassPlain type, 10mm I.D. with indents for supporting glass beads or other packing.
-
Condensers/Coolers, Rotary Evaporator
Ace GlassReplacement, borosilicate glass components for R220 rotary evaporators Product offering includes triple coil condensers, Bullfrog condensers and the lower condensate coolers for rotary evaporators. Available in either plain or safety coated versions. Units include black SVL caps & red GL thread…
-
Simple absorption chromatography column for rapid preparative separations with moderate resolution. Allows separations of samples from 0.01 to 10.0g in 10-15 minutes. Column and reservoir, only, are Epoxy Coated. Reservoir connects between column and flow control adap-ter. Joints on column,…
-
Condenser, Air Reflux
Ace GlassMicroscale air condenser normally used in reflux experiments. When packed with desiccant material, condenser becomes a drying tube. With inner joint at bottom, outer joint at top. Codes -10, -14 and -17 supplied with drip tip for use with 9595 Spinning Band Column. Effective length, approximately…
-
Lab Stand Support Shelf
Ace GlassLab stand support shelf fits any stand with up to 5/8"od rod. Stand measures 7 x 10" and is available with or without 4" rubber-bordered center hole. Manufactued from light, cast aluminum and epoxy coated. Rod mounted codes -04 & -06 feature a 5/8in OD x 12in long stainless rod with a through hole…
-
Chromatographic column with integral reservoir and #15 Ace-Thred at top, and 2mm bore 1:5 taper PTFE plug at bottom. Column supplied with 7506-06 Nylon bushing and FETFE O-Ring. Complete item consists of column with bushing and O-Ring, and 5853-07 Tubing Connector for connecting 12.5 to 14mm O.D.…
-
Cold Finger Condenser
Ace GlassCold Finger accessory for standard distilling heads and systems. This cold finger has an inner joint that fits inside the upper outer joint and tube to provide added cooling ability and faster condensation. Fits into 6606, 6609, and 6613 distillation h
-
High performance, non-packed, low pressure liquid chromatography columns, epoxy-coated. Simple to assemble, PTFE (no O-rings), safe operation to 150psi with safety shield. Usable with various packing materials chemically inert, zero dead volume, leak free. For analytical or preparative…
-
Clamp, Quick Release
Ace GlassStainless Steel Quick Release clamp for use with two-piece Pressure Reaction Flasks and Heads with Duran flanges. Available with or without rod for clamping to support frame. Note: Ensure proper bottom support for your reactor, the clamp is only recommended for stabilization, not support.
-
Chromatographic Column, 1:5 PTFE Plug
Ace GlassChromatographic column with integral reservoir at top, and 2 mm bore 1:5 taper PTFE stopcock plug at bottom. Opening at top is either 24/40 outer joint or opening for #3 stopper. Available with or without porosity B (70-100micron), fritted disc sealed in.
-
Condenser, Friedrichs
Ace GlassWith molded spiral condensing surface and joint at bottom and top. Jacket length 250mm. Available in various joint sizes with hose barbs or Ace-Safe connectors.
-
-
Funnel, Addition
Ace GlassFor charging columns. The capacity is approximately 5 times the largest column volume. Size listed is Ace-thred designation which refers to I.D. of tubing above thread and corresponds to 5820 column dia- meter. Available in cylindrical or conical shapes.
-
Designed for metal recovery using Ion-Exchange resins such as Amborane. Borosilicate glass column has #25 Ace-Thred at both ends. Polypropylene end fittings form a leak-tight seal with FETFE O-Rings. Fittings have 1/4" npt female thread for connecting 3/8" O.D. flexible vinyl tubing from…
-
The improved design of ACE extractor condensers permits greater condensing capacity, cycling rates may be doubled over conventional style extractors. Complete consists of flask cap, condenser, extractor, and flask.
-
Standard Clamp
Ace GlassClamp is designed to fit 4 inch conical flanges, allowing the top half to be removed without disturing the lower half. Clamp features and extension arm (1/2 x 8 inch) suitable for attachment to an appropriate support stand or lab frame. Silicone liner will withstand temperatures up to 500ºdegF.