Ace Glass, Filters, Supplies
-
Tube, Pressure Filtering
Ace GlassUsed in filtering glucose, agar and serums. All porosities of a given size are priced the same. Top accepts #3 or #4 rubber stopper.
-
Tube, Sulphur Absorption
Ace GlassFor sulphur absorption chamber, after Edgar and Callingaert. Diameter of disc 30mm, height above disc 200mm, capacity 130mL. Will fit a No. 7 rubber stopper.
-
Tube, Gas Dispersion
Ace GlassOutside diameter of tube 8mm, total length of tube 150mm. All porosities of a given size are priced the same.
-
Tube, Allihn
Ace Glass,p>Diameter of disc 30mm, height above disc 100mm, diameter of bottom tube 8mm.
-
Tube, Filtering
Ace GlassWith fritted disc sealed on bottom. Overall length 125mm. All porosities of a given size are priced the same.,/p>
-
Tube, Gas Dispersion
Ace GlassWith porous fritted glass tip. Available in 150mm and 300mm lengths. O.D. of both lengths, 10mm. Fits through #11 Ace-Thred.
-
Tube, Gas Dispersion
Ace GlassDisc diameter 10mm, length 150mm. Disc approximately 2mm thick. Outside diameter of tube 7mm.
-
-
Tube, Gas Dispersion
Ace GlassFritted disc is angled approximately 15 degree from stem, which permits the small gas bubbles to rise from the disc surface without excessive formation of large bubbles. These tubes give a performance compared to a horizontal disc, but the method of co
-
Tube, Gas Dispersion
Ace GlassSupplied with 6, 7 or 8mm O.D. stem tubing, 150mm in length. Maximum O.D. of stem and filter disc is 20mm. Filter disc is 10mm diameter, porosity B (70-100 m).
-
Fritted filter disks for Ace Membrane Filtration Apparatus. Special tight outside diameter and tolerance to fit 3702-10 and 3700-10 filter adapters.
-
Tube, Straight
Ace GlassFor construction of special apparatus. All porosities of a given size are priced the same.
-
-
Filter Disc, Packing Support
Ace GlassFilter discs available in plate glass, polyethylene (100 micron) and fritted glass porosities A (145-174 microns), B (70-100 microns), C (25-50 microns), and D (10-20 microns).
-
Filter Material, Discs and Fabric
Ace GlassFilter material and discs (paper, PTFE, and polypropylene).
-
Tube Reduced Ace-Thred Ends
Ace GlassFilter tube with #15 Ace Threds on ends and an integral fritted disc. Disc diameter is 50mm and is available in different porosities. Supplied with #15 nylon bushings and 1/4" polypropylene hose barbs.
-
Tube, Gas Dispersion
Ace GlassFor fine dispersion. Porous tip approximately 5mm or 7mm O.D. x 10mm. 7mm O.D. Tube fits #7 Ace-Thred. Offered with Porosity A (145-174 micron), Porosity B (70-100 micron), Porosity C (25-50 micron), Porosity D (10-20 micron), or Porosity E (4-8 micron
-
Glass Filter Disc
Ace GlassFilter discs, available in glass fiber or granular type. Glass fiber filter discs last longer, are more abrasion resistant, and are superior in performance than granular type discs. Granular discs for analytical and general bacteria filtration are avai
-
Tube, Gas Dispersion
Ace GlassOutside diameter of tube 8mm, total length of tube 150mm. All porosities of a given size are priced the same.
-
Filter/Regulator/Lubricator
Ace GlassSpace-saving, multiple unit. Element removes impurities down to 40 microns. 150 PSI maximum pressure range is adjustable through spring action of T-handle. Maximum operating temperature is 125 degree F. Manual drain. Shatter-proof polycarbonate bowls not recommended for use in atmospheres…
-
Tube, Gas Dispersion, 15 degree Angle
Ace GlassGas dispersion tube with porous fritted tip for use with #7 Ace-Threds. Tube is bent 15 degree to allow positioning inside flask to avoid stirring paddles and yet reach close to bottom of flask. Specify porosity and length or code when ordering.
-
Tube, Reduced Ends
Ace GlassThese filters are supplied in a range of sizes from the 20mm disc size to the 50mm disc size. The smaller sizes are used to remove end products of a reaction during recirculation of liquid reactants, the larger units are suitable for filtering operatio
![Site Search powered by SLI Systems](http://assets.resultspage.com/logos/sli_logo_2014.png)