A high velocity impinger (Ref. AGI-4) which passes 12.3 to 12.6L/min. (corrected to engineering standard gas conditions) when the pressure drop across the orifice is 41cm Hg or greater. Stopper fits 24/25 125ml bottle and features a 11mm OD center tube, 8mm OD side arm with bulge, 0.05in capillary…

Adjustable bleed adapter used for reducing air flow in the Air Sampling Manifold to prevent a pressure drop across the sampling ports. Normally installed in front of the 7511 blower, in line with the manifold. Positioning of holes in threaded nylon plug controls the volume of air flow. Plug…

7493 air sampling cane 6.4mm mesh PTFE screen assembly. Only available for our 25mm OD canes. Place the screen within the retaining ring, unfasten the yoke's nut & bolt, pass the now open yoke around the funnel and then tighten the nut and bolt to secure the assembly. The screen is held in place…

Consists of bottle with hex base and 45/50 joint, SO2 bubbler stopper with 25 mm diameter Por. C (25-50m) fritted disc, and impinger stopper. Capacity, 275mL. Inlet/outlet are 8mm.

Borosilicate glass vacuum/NO-AIR trap. Simliar to 8755 traps but with No. 15 O-Ring side connecting joints. Ideal for vacuum cart and other vacuum or NO-AIR applications. Comes complete with stainless steel ball-joint clamp and Viton O-Ring.

Vacuum, NO-AIR adapter for vacuum cart, vacuum manifolds and Schlenk lines. Has No. 15 O-Ring joint side port with a Hi-Vac valve for precise flow control and an ACE-THRED bottom outlet.

Roof attachment for securing sampling cane to roof of van. Fabricated of Nylon with two O-Rings that make a watertight seal. Threaded length is 20.3cm (8").

Bubbler with either fritted tip or plain orifice stopper. Bottle has 24/40 joint and 10 cm tube below bulge. Stopper has 12/5 outer joint on inlet arm and 12/5 inner on outlet arm. Fritted tip is porosity C (25-50m). Orifice tip is 1.5mm capillary with end tapered. Approximate capacity, with…

Impingers used for sampling small air volumes at low velocities. Bottle with 24/40 stopper joint is available in 25 or 30ml sizes. The stopper is available with an open nozzle or one calibrated to deliver 0.09 to 0.11 CFM at 30.5cm (12in) vacuum. The stopper inlet is available as an open tube end,…

Collection bottle, usually connected to the bottom arm of the 7495 tee with reduced ends, to collect heavy particulates before they enter the manifold train.

Aluminum blower mount for connecting 7511 blower to glass manifold. With threaded stock.

Glass Manifold with #15 Ace-Thred at either end To allow switching 5853 vacuum connection to left or right side. Supplied with three or five, 4mm straight bore PTFE stopcock sampling ports. (Additional ports can be ordered.) Overall length of glass manifold is 230mm. Complete item consists of 8763…

All-glass check valve with ground seat and precision ground solid ball. Suitable with mercury in the vertical position, more sensitive to other fluids in the horizontal position. Connections are 8mm O.D.

Double tube vacuum manifold with 4 x #15 o-ring joint ends. Available in 3 or 4 port configuration with Easy Action 0-10MM stopcocks. The ports can be ordered with either 14/20, 24/40 inner joints or #15 o-ring joints. Distance between ports is 100MM which will allow for flasks up to 250mL. Please…

Schlenk style reaction tube for vacuum and No-Air applications. Available in many capacities, joint sizes and side arm configurations including a glass stopcock, 0-3 inlet valve or a 0-4 Hi-Vac valve.

Schlenk style reaction tube for vacuum and No-Air applications. Available in many capacities, joint sizes and side arm configurations including a glass stopcock, 0-3 inlet valve or a 0-4 Hi-Vac valve.

Straight tube type air sampling cane with polyethylene hood and stainless steel brackets. Codes -35 & -37 feature a #7 Ace-Thred port for introducing calibration gases.

An all-glass check valve with ground seat for liquid seal. Available in style A for vertical use, and style B for right angle connection. Connections are 8mm O.D.

Schlenk style flask for vacuum, NO-AIR or gas applications. Can be used for storage or reactions. Top is either a no.15 o-ring or outer standard taper joints. Side arm has either a 0-3 inlet valve or a 2mm or a 4mm glass stopcock.

Imhoff sedimentation cone for the determination of settleable matter in water. Either blunt tip or Ace-Thred tip for environmental applications. Graduated from 0-2ml in 0.1ml divisions, 2-10ml in 0.5ml divisions, 10-40ml in 1ml divisions, 40-100ml in 2ml divisions.

Sampling tee with top threaded, side and bottom tubes reduced for use with 7506 bushing.

Used for sampling air volumes at low jet velocity. Bottle joint is 24/40. Stopper uses #7 Ace-Safe removable hose connections for easy connect/disconnect. Impinger nozzle calibrated to deliver 0.09 to 0.11 CFM at 30.5cm (12") H2O vacuum. Bubbler nozzle has sintered glass filter, porosity A…

A rapid, efficient and foolproof Purge Valve for 100% replacement of air in reaction vessels with any desired gas (N2, H2, Ar, Cl2, etc.). No mercury used, no reducing valve needed on gas source, no high vacuum source necessary. No need to watch manometers, hand control gas flow, or install warning…

A high velocity impinger air sampling which passes 6L/min (corrected to engineering gas conditions) when the pressure drop across the orifice is 41cm Hg or greater. Stopper fits 24/25 125ml bottle and features a 11mm OD center tube, 8mm OD side arm with bulge, 0.035in capillary tip that is…

Vacuum/gas manifold with a Firestone Rapid Purge Valve at one end and 0-5mm High Vacuum, Easy Action PTFE Stopcock ports with 3/8" 0.D. Swagelok tubing connections. Each connection has an O-Ring groove (O-Rings supplied) for use with #11 Ace-Thred. Valve eliminates the need for a second tube.…

Filter support assembly for collecting dust particles in a stack sampling system. Available in either 51mm (2"), 76mm (3") or 102mm (4") (illustrated) size. Consists of: PART A, with 28/15 outer joint bent perpendicular to flow path; PART B, with seat for fritted disc and 28/15 inner…

Graduated Schlenk storage tube with 14/20 or 24/25 outer top joints, 14/35 or 24/40 inner joint side arms, stopcock inlet or hose barbed inlet valve. Reaction accessories include 7759 series filter tubes, 7807 series finger condenser, 9543 series stoppers and 13657-33 stirring magnet..

Glass Manifold with #15 Ace-Thred at either end to allow switching vacuum connection to left or right side. Supplied with three or five 0 - 4mm High Vacuum, Easy Action Stopcocks for sample ports. Plugs are PTFE with Nylon hooded handles and FETFE O-Rings. Ultimate vacuum of 10 - 7 can be realized…

Single tube vacuum manifold with #15 o-ring joint ends. Available with 3 or 4 high vacuum stopcock ports. Order with inner joint port ends (14/20 or 24/40) or #15 o-ring joints. The distance between ports is 95mm, ideal for flasks up to 250mL. Please see our various o-ring joint adapters such as…

Single tube vacuum manifold with 35/20 ball joint ends. Available with 3 or 4 high vacuum stopcock ports. Order with inner joint port ends (14/20 or 24/40) or #15 o-ring joints. The distance between the ports is 95mm, ideal for flasks up to 250mL. Please see our various o-ring joint adapters such…

Identical to 7531-10 with the exception that the nozzle is replaced by a sintered glass filter, porosity A (145-175 microns). Used in determination of Acrolein: 4-Hexylresorcinol Method #1. Bottle has encircling graduations from 0 to 25mL or 0 to 30mL in 5mL divisions. Inlet/ outlet are 7mm O.D.…

Air sampling cane with funnel at one end to avoid water droplets from collecting at edge and being sucked into manifold train. Bulge above the funnel is for glass wool or similar material to allow for filtering of particulates. Codes -22 & -26 feature a #7 Ace-Thred port for introducing calibration…