Bubbler

…assembly during mercury analysis Reagents injected by needle penetration of rubber stopper diaphragm; dispersed into sample through fritted bubbler tube Ground glass joint fits into neck on standard 300 mL BOD bottle (see Thomas number 1781N43) Air inlet and outlet, 5 mm o.d.;…

Identical to 7531-10 with the exception that the nozzle is replaced by a sintered glass filter, porosity A (145-175 microns). Used in determination of Acrolein: 4-Hexylresorcinol Method #1. Bottle has encircling graduations from 0 to 25mL or 0 to 30mL in 5mL divisions. Inlet/ outlet are 7mm O.D. For…

With small ball joints to prevent mineral oil being sucked back under sudden negative pressure in the system.

Features and Benefits Threaded Midget Bubbler - 20mm threads. Fritted glass stem. Back pressure <7 in. of water with 15mL water. 6-dram vial (22mL) included. General description These borosilicate glass impingers (for particles) and bubblers (for gases and vapors) are ideal for NIOSH…

BUBBLERS, HIGH CAPACITY, CHECK VALVES, High capacity check valve bubbler keeps oil and air from being drawn into a reaction system when negative pressure is developed. Bubbler has two 1/2" swagelock type fittings on top permitting one side to be connected to the nitrogen source and one side to…

Used with mineral oil to observe gaseous addition to reactions. May be used to vent a reaction mixture to the atmosphere. Tubing connections are 8 mm O.D. and may be used with 179730-0808 or 179920-0808 to join multiple bubblers if necessary.

Sparging accessory for vertical sidearm spinner flasks. Manufactured from 316l stainless steel with electropolish finish. Includes polypropylene cap with 1/4? white compression fitting and white silicone gasket. .040 inch hole for aeration of fermentation cultures where shear force is less critical.

Sparging accessory for vertical sidearm spinner flasks. Manufactured from 316l stainless steel with electropolish finish. Includes polypropylene cap with 1/4? white compression fitting and white silicone gasket. .040 inch hole for aeration of fermentation cultures where shear force is less critical.

Used to make a vent to the atmosphere. May also be used with mercury when adequate ventilation is available. Reservoir head prevents oil from being sucked back into the system. With 8mm O.D. tubing connections. Volume approximately 40mL below side arm.

Bubbler, Ground Joints, Top Joint: 29/42, Bottom Joint: 14/20 OR 24/40, Length: 157mm **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**

Synthware adapter with oil bubbler. With standard taper inner joint. Horizontal design allows for in line connection for apparatus purging.

…removable hose connections for easy connect/disconnect. Impinger nozzle calibrated to deliver 0.09 to 0.11 CFM at 30.5cm (12") H2O vacuum. Bubbler nozzle has sintered glass filter, porosity A (145-175 microns) or porosity B (70-100 microns). Bottle has encircling graduations from 0 to 25mL or…

…particles) and bubblers (for gases and vapors) are ideal for NIOSH and OSHA methods that require collection of airborne contaminants by drawing them into a solution. Available with ground glass joints or threaded PTFE micro-connectors. Synonyms: Impinger/Bubbler; Midget bubbler w/frit, 24/40 gr…

Mineral Oil Bubbler, Body OD: 26mm,Overall Height: 185mm OR 500mm, Hose Connection: 10mm **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**

Push-fit onto a 1/8" OD tube for a quick connection These reservoir filters and bubbler provide simple and effective solvent filtration. A 10 µm filter ensures even the smallest particulates are removed from the solvent supply line. Bottom-of-bottle filters have slots in the body…

Bubbler with metering valve for precise control of inert gas introduction and features 9mm OD tube-end side arms for use with 3/8in ID vacuum tubing.

Bubbler with either fritted tip or plain orifice stopper. Bottle has 24/40 joint and 10 cm tube below bulge. Stopper has 12/5 outer joint on inlet arm and 12/5 inner on outlet arm. Fritted tip is porosity C (25-50m). Orifice tip is 1.5mm capillary with end tapered. Approximate capacity, with stopper…

Bubbler has an adjustable inner tube with a #9 Chem-Thread. Taper at bottom of reservoir allows for use of a minimal amount of oil. Complete bubbler consists of the lower reservoir, adjustable inner tube, compression cap and Viton o-ring.

Horizontal design of bubbler allows for in line connection and purging of apparatus. Hose connection has a 9mm OD middle serration. Complete with standard taper inner joint.

Similar in design to AF-0513 but with two oil reservoirs. Bubbler is approx 125mm W x 135mm H. Hose connections are 9mm OD at the middle serration.

…reactions while providing a vent to the atmosphere. Bubbler has a "T" connection at the top to allow it to be mounted in-line while the reservoir head prevents oil from being sucked back into the system. Volume below the sidearm is approx 40mL. Bubbler has 8mm OD top and side tubulations.

With completely adjustable 7mm inner tube. Tube has a pulled tip and is secured by a #7 Ace- Thred. Volume approximately 40mL. Tapered bottom of vessel allows for use with small volumes. Nylon bushing supplied with FETFE O-Ring. Available modified with #7 Ace-Threds on inlet/outlet for use with…

Used to monitor gas flow to reactions while providing a vent to the atmosphere. Reservoir head prevents oil from being sucked back into the system. Volume below the sidearm is approx 40mL. Bubbler has an 8mm OD top and side tubulations.

…head prevents oil from being sucked back into the system. Standard taper inner joint is for use in single or multi-neck flasks. Hose connection has a 9mm OD middle serration. The 24/40 jointed bubbler is available in two sizes; the larger for use in vessels having a capacity greater than 100mL.

Micro impinger designed for sampling of small volumes of air at low jet velocity, as per EPA Method 6. Impinger bottle is graduated from 5 to 30mL in 5mL subdivisions. Both the bottle and stopper have 24/40 standard taper joints. The nozzle being replaced with an extra coarse fritted gas dispersion…

Manufactured from 316L electropolished 1/4" stainless steel with hose barb. Ideal use for sparging of vertical sidearm spinner flasks. Includes polypropylene cap with 1/4" compression fitting and white silicone gasket. 10 Micron porosity frit for cell cultures where shear is critical. …

Bubbler has an integral valve to control the flow of inert gas into the system. Bubbler requires a minimal amount of oil due to the inner tube being within 5mm of the bottom. Both sidearms are 9mm OD for use with 3/8" Cajon®; fittings. Overall height is approx. 220mm.

Unique design of bubbler allows for fine control of purge gas within an inert gas system such as a manifold. Purge gas enters bubbler through hose connection (A) and exits thru connection (B) which is connected to manifold. The large capacity of the main chamber (C) allows for rapid purging with…

Sparging accessory for vertical sidearm spinner flasks. Manufactured from 316l stainless steel with electropolish finish. Includes polypropylene cap with 1/4? white compression fitting and white silicone gasket. .040 inch hole for aeration of fermentation cultures where shear force is less critical.…

L-Bubbler Tube w/ 10 .040 Holes, 15L Vertical Sidearm Vessels. Manufactured from 316L stainless steel. Supplied with cap and compression fitting. Specifications: Material: 316l Stainless Steel Ra 32 Finish Or Better Dimensions: 18 1/2" X 4 3/4" X.250" Tube With Hose Barb End .040…

Sparging accessory for vertical sidearm spinner flasks. Manufactured from 316l stainless steel with electropolish finish. Includes polypropylene cap with 1/4? white compression fitting and white silicone gasket. .040 inch hole for aeration of fermentation cultures where shear force is less critical.…

Sparger for vertical sidearm spinner flasks. Includes polypropylene cap with 1/4? compression fitting and white silicone gasket. Material: 316l stainless steel with electropolish finish Ra 32 finish or better Size: 21?