Supplies, Bellco Glass, General Lab Products
-
Bell-Flo IOB Assembly 100mL
Bellco GlassBell-Flo iob assembly was designed to be used with the bell-flo vessel with bottom indents and 3 vertical baffles for optimal mixing. Rugged stainless steel ptfe internal bearing impeller assemblies utilize a wing style impeller blade that increases mixing and oxygenation to your cell culture. Cap…
-
1.7in. Probe Holder 45mm
Bellco GlassBellco stainless steel probe holder is designed to be used with our 45mm blue polypropylene open top caps and white silicone gaskets. A wide variety of fittings are available to allow ph and do monitoring via insertion of these probes into the sidearms of the vessels. Threaded probe adapters are…
-
Large Flange Round Bottom Vessel 3L
Bellco GlassHeavy walled construction for cell culture and fermentation applications. Heavy duty o-ring flange creates positive seal for stainless steel head-plate. For use with stainless steel head-plate, o-ring, and locking clamp. Use with CellTrol ii only single or dual systems, and speed control modules.…
-
Low Profile 3-Port Thermowell Assembly 6L
Bellco GlassThermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube. Port Thermowell assembly For low profile 3l vessel Material: 316l…
-
Straight Harvesting Tube 10L 1/2"
Bellco GlassMaterial: 316l stainless steel with ra finish of 32 inch or better, inside and out Dimensions: od x id:1/2? x .430? x 10? long
-
-
3-Port Thermowell Assembly 8L
Bellco GlassThermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube. Port Thermowell assembly For low profile 3l vessel Material: 316l…
-
Large Flange O-Ring Only 200mm
Bellco Glass200 mm large flange 0-ring for use with SST flange clamp. 200 mm 0-ring Red silicone rubber construction
-
Baffle Assembly 7L Large Flange
Bellco Glass316l stainless steel baffle assembly for use on large flange 7 liter bioreactor vessel system. Attaches to the head plate. used to change the mixing characteristics within the bioreactor. 3 required per vessel 1/4? rod Silicone 0-ring
-
Glass Micro-Carrier Impeller Shaft 6-8L
Bellco GlassManufactured from type 1 class a Borosilicate glass. For spinner flasks 3l to 36l Dimensions: 9mm x 400mm long
-
Stainless Steel Probe Capseal 1L w/ PTFE IOB 4 Ports
Bellco GlassThe stainless steel 100mm iob probe cap seal is manufactured from 316l stainless steel and has a red-silicone sealing gasket with a 100mm blue polypropylene screw cap. The stainless steel probe cap seal has four accessory ports surrounding a centrally located internal impeller assembly. Two of…
-
Round Bottom Marine Impeller 8L
Bellco GlassDimensions: 1/2? od x 12 1/2? long Stainless steel 4? od right hand pitch marine prop & e-clip Material: 316l stainless steel with electropolish finish For round bottom omni vessel (1964-88405) Need l/f head plate, over head drive motor Size: 8l
-
Removable baffle for large flange vessels. Material: SST 36l with electropolish finish Dimensions: 1 1/2" wide x 10 1/2" long Fits on any 1/4" od SST tube inside vessel Recommend: 2 per vessel Z-shaped
-
3-Port Sparger Assembly w/ Frit 15L
Bellco Glass316-l stainless steel ra32 or better finish 10 micron porosity stainless steel frit for low profile vertical side arm vessels. Frit is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket Triple tube configuration with vent, fill/sample and sparge.
-
Bellco Heating Blanket 230V-36L-HW 1200 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 1200 - not to be use with CellTrol Watts: 1200 Dimension…
-
IOB Impeller Assembly 15L
Bellco GlassStainless steel shaft design prevents cell damage and minimizes magnetic decoupling. Sealed internal assembly requires less incubator space. For use with bellco 1965-series standard and water jacketed spinner flasks. Cap size: 100mm Flask size: 15l Paddle: 9 1/2" x 6"
-
Micro-Carrier Impeller Assembly 1-3L
Bellco GlassImpeller assembly for micro-carrier spinner flasks. Consist of magnet holder, silicone plug, magnet, and ptfe paddle. Impeller size: 1-3l Paddle dimensions: 1 3/4" x 4 1/4" Consist of: Magnet holder: a523-207 Silicone plug: a523-200 Magnet: 1975-0300a Ptfe paddle: a523-206
-
Process Micro-Carrier Insect System 3L 230v
Bellco GlassDesigned for growing insect cell cultures such as sf9 and sf21 cells. The system comes complete with all accessories needed to grow your insect culture line for expression. 7785-p2015 process 5-position magnetic stirrer, 115v 1965-03000 micro-carrier spinner flask complete, 3l 1965-20003r 2-port…
-
Compression Fitting 5/16in. For 1/2 Hole"
Bellco GlassBellco compression fittings are designed using our standard 45mm blue polypropylene open top caps and white silicone gaskets. A wide variety of fittings are available to allow ph and do monitoring via insertion of these probes into sidearms or vessels. Bellco probe adapters are designed to allow…
-
Metal Stone Sparger 5L For Flat Bottom Omni Vessels
Bellco GlassMetal stone sparger 5l for flat or round bottom omni vessels. Sparger inserts through stainless steel headplate fitting. 4 1/2?wide x 12? long 316 l stainless steel ra 32 finish or better Stainless steel frit
-
Glass Ball Impeller Only 100mL
Bellco GlassGlass ball houses a magnet for gentle agitation of micro-carrier beads and has a 70mm cap. Specially formed bottom indent prevents accumulation under the impeller Cap size: 70mm Size: 100ml
-
Straight Harvesting Tube 6L 1/4"
Bellco GlassMaterial: 316l stainless steel with ra finish of 32 inch or better, inside and out Dimensions: odxid:1/4? x 5/32? x 6.0? long
-
Stainless steel curved harvesting tube for 36l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 36l Dimensions: 1/4" x 5/32 x 24"
-
-
3-Port Sparger Assembly w/ Frit 36L
Bellco Glass316-l stainless steel ra32 or better finish 10 micron porosity stainless steel frit for low profile vertical side arm vessels. Frit is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket Triple tube configuration with vent, fill/sample and sparge.
-
Valley Heating Blanket 115V-15L-Low Watt 325 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 15l Watts: 325 - low wattage Dimension (in.): 5 x 33 1/4…
-
Stainless Steel Shaft Assembly 100mL
Bellco GlassManufactured from 316l stainless steel. Impeller assembly for micro-carrier spinner flasks. 1965 series micro-carrier spinner flask Size: 100ml
-
Large Flange Z/Z Paddle 15L
Bellco GlassManufactured from 316l stainless steel with electropolish finish. Ra 32 finish or better inside and out. Ideal use for cell culture and reduces shear in delicate cell culture. Blade dimension: 5 3/4 x 2 1/2? Shaft oal: 14 1/4? Constructed of 316l electropolished stainless steel Marine impeller…
-
Bellco compression fittings are designed using our standard 45mm blue polypropylene open top caps and white silicone gaskets. A wide variety of fittings are available to allow ph and do monitoring via insertion of these probes into sidearms or vessels. Bellco probe adapters are designed to allow…
-
Stainless Steel Shaft Assembly 1L
Bellco GlassManufactured from 316l stainless steel. Impeller assembly for micro-carrier spinner flasks. 1965 series micro-carrier spinner flask Size: 1l
-
Glass Ball Impeller Only 250mL
Bellco GlassGlass ball houses a magnet for gentle agitation of micro-carrier beads and has a 70mm cap. Specially formed bottom indent prevents accumulation under the impeller. Cap size: 70mm Size: 250ml
-
Stainless Steel Bent Harvesting Tube 36L 1/4"x20"
Bellco Glass316l stainless steel bent harvesting tube for 36l flat bottom omni vessel. Use with large flange head-plate. Size: 1/4" x 20" Id: 5/32"