Stirrers, Ace Glass, Chemicals
-
Stirrer, Complete
Ace GlassPrecision Trubore Stirrer Assembly consisting of 10 mm ID bearing, bushing, precision ground, button type glass shaft and blade. Available with either glass or PTFE stir blade.
-
Bearing, Trubore, Plain, 10mm
Ace GlassInterchangeable bearing designed to be used with our precision ground stirring shafts (8068,8070,8071,8073,9532,9533). Recommended top stirring speed with our 8117 Stir-Lube is 1500 rpm.
-
Chlorofluorocarbon grease for use at speeds up to 6000 r.p.m. with ACE standard glass assemblies. Use 8040 water-cooled type bearing for long-time stirring (over one hour). Below one hour, 8038 type may be used at 1500 r.p.m.; eight hours at 1000 r.p.m. High chemical inertness unaffected by strong…
-
Bearing, Trubore, 10mm
Ace GlassFor use with Flask Head 9443. By using precision bore tubing throughout the length of the bearing, a stirrer is produced that will hold to within 1mm of vacuum and withstand pressures in the flask up to 300mm. The 9532 Agitator, used with this bearing actually develops a negative pressure of 230mm…
-
Agitator, PTFE, Multi-Paddle, 10mm Shaft
Ace GlassPTFE multi-paddle agitator for 10mm OD drilled or knob type shafts. Paddles are replaceable. Fits 10mm OD drilled or knob type 8068, 8071 and 8079 shafts.
-
Precision ground glass stirring shaft with attached vanes, 10mm. For use when agitation and gas introduction are desired at the same time. Agitator will fit through a 45/50 joint. Designed for use with our 9523 Trubore bearing and 9443 or 9446 mini-lab flask heads. Introduced gas exits the hollow…
-
Agitator, PTFE, Large scale, Turbine
Ace GlassA turbine type agitator, available for 19mm and 28mm shafts. 19mm six blade agitators are open in the center to allow custom positioning on drilled type or knob type 8076, 8078 & 8079 shafts. 28mm four blade agitators are supplied with a PTFE nut & bolt set for securing to 8080 shafts. Shaft is not included.
-
Offset gearbox and motors complete with right angle drive unit for pilot plant systems. Motors with right-angle drive save headspace and work well where height is restricted. Available for standard or hazardous duty applications. Available in either 1/4hp or 1/2hp with a digital 115/230v 50/60Hz…
-
Stirrer, Laboratory, Solid State
Ace GlassTotally enclosed, 1/40hp DC permanent magnet motor with dual 8 mm (5/16") armature and gear shafts with milled flats. Armature shaft with maximum speed of 4000rpm.; 18:1 ratio gear shaft rated 3.6in-lb torque, up to 333rpm. Motor supplied with 1.5 meter 3-wire cable for controller connection.…
-
Agitator, PTFE, Large Scale Multi-blade
Ace GlassThese heavy-duty PTFE agitators impart maximum energy and are offset at the bottom to accomodate slurries. 10mm agitators fit drilled type or knob type 8068, 8071 & 8075 shafts. 19mm agitators fit drilled type or knob type 8076, 8078 & 8079 shafts. 28mm agitators fit 8080 drilled shafts.
-
Stirrer Blades, PTFE, Oval, 10mm Shafts
Ace GlassPTFE oval stir blades for 10mm OD button type stir shafts. 10mm OD shafts can be found in our 8068, 8070, 8074 and 8075 series.
-
Stirring bars with large, 25mm (1 inch) raisied center ring.
-
Bearing, Trubore, Pressure, 10mm
Ace GlassDesigned for use with #25 Ace-Thred. Consists of a Trubore bearing, pressure bushing, gland with two O-Rings and retainer bushing with o-ring. For use with our precision ground stirring shafts (8068,8070, 8071,8073,9532,9533) and reservoir as part of our 7898 Thin Film reaction system.
-
Agitator, PTFE, 4 Blade
Ace Glass4 Blade PTFE agitator available with either 45 or 90 degree blade angle. For use with glass or metal shafts and is secured using a compression style fitting allowing it to positioned anywhere along the length of the shaft.
-
Bearing, Trubore, Gas Balancing, 10mm
Ace GlassThis bearing is supplied with tubulation for feeding inert gases around the bearing to balance any pressure possibly being developed in the flask. Can also be used for gas-liquid reactions and gas dispersions using our hollow precision ground stirring shafts (8068, 9532).
-
Stirrer Assembly, Vacuum, Debris Free
Ace GlassRotating ball joint seal gives vacuum-tight connection good into the micron range. Ultimate vacuum is determined primarily by the tightness of the vinyl tubing connector which fastens the unground shaft to the ball member. Operate below 500 rpm. Use with unground stirring shafts (8134,9530).…
-
Bearing, Trubore, 5 & 6mm
Ace GlassTrubore bearing with standard taper joint for use with our 9534, 9535 and 9541 precision ground stir shafts. Lubricant well at top will accept enough 8117 Stir-Lube to provide hours of operation at up to 1000 rpm. Match bearing ID with stir shaft OD.
-
Precision ground glass stirring shafts,10mm OD, crescent type. Useful for stirring viscous materials at low rpm. Available for round bottom flasks of 1, 3 and 5 liters. Code -19, 3 liter size will fit a 2 liter flask, but closely. Flask opening must be 29/42 or larger. Use with Trubore bearings…
-
PTFE agitator with removable blade secured with a PTFE pin. Supplied 3.2x15.2cm blade will fit through a 45/50 joint. Fits 19mm od drilled type or knob type 8076, 8078 & 8079 shafts.
-
Stirring Shaft, PTFE Coated Glass, 10mm
Ace GlassPrecision ground glass stirring shafts, 10mm OD, button type, PTFE coating permits higher stirring speeds with Trubore bearings. If used unlubricated, 500 rpm max with water-cooled 8040 bearing. Compatible with 8036, 8038, 8039, 8043, 8047, 8051, 8055 and 13443 bearings. Button type shafts accept…
-
3/8HP Brushless DC motor for use on pilot plant reactors up ²to 200L. May be used with either the 120V or 240V BLDC ²motor controllers. Supplied with 6ft removable cable and ²mounting hardware.
-
Stirrer Bearing, PTFE, 6-10MM Shafts
Ace GlassPTFE stirrer bearing featuring a non-shedding, fully enclosed, anti-whip, chemically resistant design. Models available for 6, 8 and 10mm glass, metal or PTFE stir shafts. Can be used in slight pressure or vacuum applications. Maximum recommended speed for continuous operation is 500 rpm. Unlike…
-
Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8076 (19mm od) or 8080 (28mm od) polished glass stir shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…
-
Precision PTFE covered stainless steel stirring shafts, 19mm OD. Drilled type shafts accept 8091,8092,8093,8100 agitators and can be used in 19mm Trubore bearings (8059, 8060, 8061 & 8065). Not recommended for PTFE bearings 8050, 8067 and 13445. Join to stirrer motor using 8124 series chucks.
-
Stirring Shaft Coupling
Ace GlassStir shaft couplings for connecting glass or metal stir shafts to the adjustable chuck on an overhead stir motor. Compression connection is secured to various OD shafts via an Allen screw coupling. The Codes -22 and -24 are complete pass-thru assemblies that enable height adjustment on stir shafts…
-
Glass bearing design for use with Ace-Thred pressure reactors and our 8075 glass, polished or 8074 bare, stainless steel 10mm stirring shafts. Both the top bushing and bottom coupling are PTFE. Maximum operating speed is 600 rpm.
-
Agitator, PTFE, Turbine, For 10mm Shaft
Ace GlassAll-PTFE turbine type agitator. Unique locking arrangement assures positive grip. Agitator fits 10 mm shafts. Shaft opening is drilled straight thru to allow positioning of agitator at any drilled position on shaft as well as the bottom. For use with bead type glass shafts, 8068-G, 8075 or PTFE…
-
Stir Shaft, 4 Blade Propeller, PTFE
Ace GlassPTFE covered stainless steel shaft with solid PTFE, 4 blade screw propeller. Blades are pitched 45 degrees. For a better grip by the stir motor chuck, 50mm of stainless is left exposed.
-
Stirring Blade, For 5 & 6mm Shaft
Ace GlassPTFE stirring blades for use with our button type 9524 and 9527 stirring shafts. Blades are 41mm wide x 12mm high and are designed for use in flasks 250ml and less. Match blade to shaft OD.
-
Stirring shaft agitator combination available in either a solid, precision ground glass shaft or all PTFE knob type shaft with a PTFE snap-fit agitator designed to fit through 14/20 and 18/11 joints. Designed for use with our 5mm ID 9524 or 9527 bearings and flasks of 50ml and smaller.
-
Pass-Thru Rod, Flexible shaft
Ace GlassPass-thru rod for use with Caframo 13565 & 13566 stir motors attached to our 8081 flexible stirring shaft.
-
PTFE, large-scale, multi-paddle agitator design to accept pinned bottom valves, like our 6482 flush-seal valve. The pin helps reduce wobble or flexing at higher rpm. 28mm agitators will fit drilled type 8080 shafts.