Ace Glass Shaft Stirrers
-
Bearing, Trubore, Pressure, 10mm
Ace GlassDesigned for use with #25 Ace-Thred. Consists of a Trubore bearing, pressure bushing, gland with two O-Rings and retainer bushing with o-ring. For use with our precision ground stirring shafts (8068,8070, 8071,8073,9532,9533) and reservoir as part of our 7898 Thin Film reaction system.
-
Stirring Shaft Coupling
Ace GlassStir shaft couplings for connecting glass or metal stir shafts to the adjustable chuck on an overhead stir motor. Compression connection is secured to various OD shafts via an Allen screw coupling. The Codes -22 and -24 are complete pass-thru assemblies that enable height adjustment on stir shafts…
-
Precision ground glass stirring shaft, 10mm OD, attached vanes. Vanes will fit through a 45/50 joint and are contoured for use with our 9448 and 9456 series Mini-Lab flasks. Use with Trubore bearings 8036, 8038, 8039, 8040, 8042, 8043, 8047, 8051, 8053 and 8055. Compatible with our 8050 mechanical…
-
Precision ground glass stirring shafts,10mm OD, crescent type. Useful for stirring viscous materials at low rpm. Available for round bottom flasks of 1, 3 and 5 liters. Code -19, 3 liter size will fit a 2 liter flask, but closely. Flask opening must be 29/42 or larger. Use with Trubore bearings…
-
Stirrer Blades, PTFE
Ace GlassPTFE stir blades for button type stir shafts. 10mm OD shafts can be found in our product series 8068, 8070, 8074 and 8075. 19mm OD shafts can be found in our 8076 and 8077 series.
-
PTFE, large-scale, multi-paddle agitator design to accept pinned bottom valves, like our 6482 flush-seal valve. The pin helps reduce wobble or flexing at higher rpm. 28mm agitators will fit drilled type 8080 shafts.
-
Button type, solid glass stirring shafts, 5 & 6mm OD. Precision ground shafts, codes -04 & -06, should be used in matching glass Trubore 9524 and 9527 bearings. Polished shaft, code -40, should be used only in our 8066-120, 6mm PTFE inner bearing. All accept our 9542 blades. Join to stirrer motor…
-
Glass bearing design for use with Ace-Thred pressure reactors and our 8075 glass, polished or 8074 bare, stainless steel 10mm stirring shafts. Both the top bushing and bottom coupling are PTFE. Maximum operating speed is 600 rpm.
-
316 stainless steel, football shaped, stir blades for 10mm OD button type stir shafts. Holed versions, codes -70 thru -74, provide even greater agitation. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.
-
Stirring shaft agitator combination available in either a solid, precision ground glass shaft or all PTFE knob type shaft with a PTFE snap-fit agitator designed to fit through 14/20 and 18/11 joints. Designed for use with our 5mm ID 9524 or 9527 bearings and flasks of 50ml and smaller.
-
Stirrer, Complete
Ace GlassTrubore stirrer assembly consists of the standard taper outer glass bearing, PTFE inner bearing, glass-filled PTFE bushing and lock nut, compression seal saddle o-ring, PTFE blade and either a glass or stainless stir shaft.
-
Trubore bearing, heavy duty, standard taper joint, self-aligning. Unique 3 piece design of Trubore inner bearing, compression seal nylon bushing and glass standard taper adapter allows for moderate misalignment of stir motor and the bearing cannot sieze the shaft. For use with 8077 & 8078 19mm od…
-
Fully flexible drive shaft facilitates isolation of the stirrer motor from the reactor. Complete units, code -30 (91.4cm) and code -32 (152.4cm), designed for use with 8mm (5/16in) motor shaft. Purchase the optional code -27 adapter for motors with 9.5mm (3/8in) shafts. Reactor end consists of a…
-
Bearing, Trubore, Gas Balancing, 10mm
Ace GlassThis bearing is supplied with tubulation for feeding inert gases around the bearing to balance any pressure possibly being developed in the flask. Can also be used for gas-liquid reactions and gas dispersions using our hollow precision ground stirring shafts (8068, 9532).
-
Agitator, PTFE, Large scale, Turbine
Ace GlassA turbine type agitator, available for 19mm and 28mm shafts. 19mm six blade agitators are open in the center to allow custom positioning on drilled type or knob type 8076, 8078 & 8079 shafts. 28mm four blade agitators are supplied with a PTFE nut & bolt set for securing to 8080 shafts. Shaft is not included.
-
Bearing, Trubore, Plain, 10mm
Ace GlassInterchangeable bearing designed to be used with our precision ground stirring shafts (8068,8070,8071,8073,9532,9533). Recommended top stirring speed with our 8117 Stir-Lube is 1500 rpm.
-
Bearing, Trubore, Water Cooled, 19mm
Ace GlassTrubore bearing, jacketed, spherical joint. Designed to accomodate our 8112-10 packing box. For use with 8077 & 8078 19mm od precision ground glass shafts or 8079 PTFE covered shafts. Spherical joint can be clamped to prevent rotation. Trubore length of 15.2cm or 6 inches.
-
Chuck, Flex-Grip®
Ace GlassNylon chuck for use with ACE stirring shafts or other shafts of the same dimensions. Chuck has flexible insert which allows for misalignment of shaft without danger of breakage.
-
PTFE covered stainless steel stirring shafts, 10mm OD, drilled type. If used unlubricated, 500 rpm max with water cooled 8040 bearing, 100 rpm max recommended with 8036, 8038, 8039, 8043, 8047, 8051 and 8055 bearings. With condensate film as added heat transfer agent, 2000 rpm can be attained.…
-
Chlorofluorocarbon grease for use at speeds up to 6000 r.p.m. with ACE standard glass assemblies. Use 8040 water-cooled type bearing for long-time stirring (over one hour). Below one hour, 8038 type may be used at 1500 r.p.m.; eight hours at 1000 r.p.m. High chemical inertness unaffected by strong…
-
STIR-LUBE®,Trubore® Stirrer Lubricant
Ace GlassA superior, low melting, silicone base lubricant which liquefies at body temperature. Because of its composition, you need apply only a very thin film of Stir-Lube® to a stirring shaft to increase bearing and shaft life at least three times over that of a bearing lubricated with glycerine.…
-
PTFE agitator with removable blade secured with a PTFE pin. Supplied 76mm long blade will fit through a 29/42 joint. Fits 10mm OD drilled type or beaded type 8068, 8071 and 8075 shafts.
-
PTFE, large-scale, multi-paddle agitator design to accept pinned bottom valves, like our 6482 flush-seal valve. The pin helps reduce wobble or flexing at higher rpm. 19mm agitators will fit drilled type or knob type 8076, 8078 and 8079 shafts.
-
Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8074 stainless steel or 8075 polished 10mm od glass shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…
-
Agitator, PTFE, Large Scale Multi-blade
Ace GlassThese heavy-duty PTFE agitators impart maximum energy and are offset at the bottom to accomodate slurries. 10mm agitators fit drilled type or knob type 8068, 8071 & 8075 shafts. 19mm agitators fit drilled type or knob type 8076, 8078 & 8079 shafts. 28mm agitators fit 8080 drilled shafts.
-
Precision ground glass stirring shafts, 10mm OD, paddled, button type and bead type. Button type shafts accept 8083, 8085, 8086, 8087 & 8096 stir blades. Beaded shafts accept 8088, 8089, 8090 & 8091 agitators. Use with Trubore bearings 8036, 8038, 8039, 8040, 8042, 8043, 8047, 8051, 8053 & 8055.…
-
Stirrer Bearing, PTFE, 6-10MM Shafts
Ace GlassPTFE stirrer bearing featuring a non-shedding, fully enclosed, anti-whip, chemically resistant design. Models available for 6, 8 and 10mm glass, metal or PTFE stir shafts. Can be used in slight pressure or vacuum applications. Maximum recommended speed for continuous operation is 500 rpm. Unlike…
-
Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8076 (19mm od) or 8080 (28mm od) polished glass stir shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…
-
Heavy duty, 28mm O.D. glass stirring shaft for use with ACE 12845 reactors. Shafts are pre-drilled to accommodate 8091,8093 & 8101 agitators for 28mm od shafts. Recommended for use with either our 8067 Trubore™ bearing with debris trap or our 8050 non-shedding bearing. For motor connection,…
-
Ultra-Vacuum stirrer bearing for applications up to 0.6 Torr. Non-shedding bearing is manufactured from PTFE, Rulon and PEEK materials. Equally good in both vacuum and pressure applications as low as 0.6 Torr. Rated for up to 400 rpm with both glass (polished rather than precision ground is best)…
-
Bearing, Trubore, 10mm
Ace GlassFor use with Flask Head 9443. By using precision bore tubing throughout the length of the bearing, a stirrer is produced that will hold to within 1mm of vacuum and withstand pressures in the flask up to 300mm. The 9532 Agitator, used with this bearing actually develops a negative pressure of 230mm…
-
Stirrer Blades, PTFE, Oval, 10mm Shafts
Ace GlassPTFE oval stir blades for 10mm OD button type stir shafts. 10mm OD shafts can be found in our 8068, 8070, 8074 and 8075 series.