Glass, Supplies, Kemtech America
-
Synthware Distillation Adapters, Vigreux
Kemtech AmericaSynthware Vigreux distillation connecting adapter. Indenstations in lower section improve liquid/vapor contact. The standard taper top outer joint accomodates a 76mm immersion thermometer. Bottom and side joints are standard taper inner joints.
-
Synthware Thermometer Adapters
Kemtech AmericaSynthware thermometer adapter with a 5 degree offset and a serrated hose connection for vacuum. Joints are standard taper.
-
SYNTHWARE Distillation Cow Receiver
Kemtech AmericaDesigned for microscale application. With one female joint and four drip-tip male joints.
-
SYNTHWARE Solvent Still Head, High Vacuum Valves
Kemtech AmericaSolvent Still Head, High Vacuum Valves Capacity: 250mL Joints: 24/40 Valve Size: 0-4mm
-
Synthware Vacuum/Inert Gas Adapters
Kemtech AmericaAllows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. Hose connection is at a 90 degree angle to the standard taper inner joint.
-
SYNTHWARE Claisen Adapter
Kemtech AmericaClaisen Adapter, Microscale, Synthware, Joints: 14/10, supplied with two compression caps, two Viton O-rings and two PTFE-faced silicone septum.
-
Synthware Vacuum/Inert Gas Adapters with Glass Stopcocks
Kemtech AmericaSynthware vacuum or inert gas adapter has a T-bore glass stopcock allowing vessels with a standard taper outer joint to purged and evacuated. The stopcock has a constant pressure retention device and a 4 mm bore.
-
Synthware Inlet/Thermometer Adapters
Kemtech AmericaAdapter has a Nylon compression cap and a Viton o-ring to form a vacumm tight seal. Cap accommodates 5.0 - 7.5mm O.D. thermometer or gas inlet tube. To use it as a syringe port, simply replace the o-ring with a PTFE-lined septum. Supplied with one Nylon cap and one Viton o-ring.
-
Synthware Inlet Adapters with Extended Length Lower Tubes
Kemtech AmericaSynthware inlet adapter with extended length lower tube. Allows for the introduction of reactants below the interior surface. Tube extends 153mm (6 inches) below the joint. Tubing has the same O.D. on both ends of the joint.
-
SYNTHWARE Jacketed Micro Vigreux Distillation Head
Kemtech AmericaDistillation Head, Vigreux, Jacketed Thermometer Joint: 10/18 Joints: 14/20, use with 25mm immersion thermometer
-
Synthware Distillation Adapters, 75°
Kemtech AmericaSynthware distillation adapter bent at 75 degrees. Both ends are standard taper inner joints and are the same size.
-
SYNTHWARE Distilling Receivers with Tubes
Kemtech AmericaSupplied with distribution adapter, three 12mL receiver tubes and three plastic joint clip. With 135° angle between top outer joint and lower inner joint.
-
SYNTHWARE T-Shaped Connecting Tubes
Kemtech AmericaConnecting Tube, T-shaped, Synthware, Tubing OD: 8 and 10mm available.
-
Synthware Chemistry Vacuum Distilling Adapters
Kemtech AmericaWith two standard taper inner joints that are parallel and at a 75 degree angle to the connecting tube. Distance between joints is 100mm.
-
SYNTHWARE Solvent Still Head with Drainage Port
Kemtech AmericaSolvent Still Head Capacity: 500 and 1000mL available Top Joint: 24/40 Bottom Joint: 24/40 and 29/42 available Side Joint: 14/20 Drainage Port Joint: 14/20
-
Synthware Flushing Adapters
Kemtech AmericaSynthware flushing adapter is used to flush and fill attached vessels with an inert gas to provide protective storage. A ballon is connected to the top hose connection. An inert gas is connected to the side hose connection. The ballon can be expanded with inert gas at the same time as the vessel or…
-
Synthware Inert Gas Adapters with 2 Hose Connections
Kemtech AmericaSynthware Inert Gas Adapter has two hose connections 180 degrees from one another to provide a flow of inert gas over the apparatus. The joints are standard taper inner joints.
-
Synthware Distillation Adapters with Threaded Thermometer Ports
Kemtech AmericaSynthware distillation adapter with threaded thermometer port. The threaded port will accommodate a 6-7.5mm O.D. plain thermometer. The adapter has standard taper top outer joint and inner joints for the bottom and side. All joints are the same size.
-
Peptide Synthesis Vessel, Solid Phase, Synthware, Capacity: 10-100mL available, Frit Porosity: Coarse or Medium available, Frit Diameter: 15-40mm Available, GL Thread: 14 or 25, Arm OD: 8mm, Supplied with a PTFE lined cap and T-bore PTFE stopcock with 2mm bore.
-
-
SYNTHWARE Shortpath Distilling Head for Volatile Distillants
Kemtech AmericaWith the condenser being a combination of a cold coil and Leibig. Top outer joint is a 10/18 for use with a 50mm immersion thermometer. With Vigreux Indentations.
-
Synthware Inlet Adapters with Hose Connection
Kemtech AmericaAdapter has a Nylon compression cap and a Viton o-ring to form a vacuum tight seal. Cap accommodates 5.0 - 7.5mm O.D. thermometer or gas inlet tube. The 8mm hose connection can be used for N2/Ar introduction or vacuum. Supplied with one Nylon cap and one Viton o-ring.
-
SYNTHWARE Vacuum Jacketed Vigreux Distillation Heads
Kemtech AmericaVacuum jacketed Vigreux distillation head having a sealed on condenser, braced for strength. Vacuum adapter has an inner joint and a sealed in drip tip. To be used with a 25mm immersion thermometer .
-
SYNTHWARE Distilling Heads for 76mm Thermometers
Kemtech AmericaThermometer joint is 10/18 for 76mm immersion thermometer. Side arm is at 75° angle.
-
Peptide Synthesis Vessel, Solid Phase, Vacuum, Synthware, Capacity: 10-100mL available, Frit Porosity: Medium abd Coarse availabe, Frit OD: 15-40mm available, GL Thread: 14 or 25 available, Hose Connection OD: 8mm, Supplied with PTFE lined screw cap and straight bore stopcock with 2mm bore.
-
Synthware Rotary Evaporator Anti-Splash Traps, Modified
Kemtech AmericaTrap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With two 4mm drain holes at the base of the inner tube to allow solvent to drain back into the evaporation flask. Has upper outer and lower inner standard taper joints.
-
SYNTHWARE Inlet/Thermometer Adapter
Kemtech AmericaThermometer Adapter, Microscale, Synthware, Joints: 14/10, Thermometer OD: 5.0-7.5mm, supplied with one compression cap and one Viton O-ring.
-
SYNTHWARE Short Path Vacuum Jacketed Distillation Apparatus
Kemtech AmericaVacuum jacketed design for more efficiency. When a thermometer is inserted in the top of this apparatus, the bulb and stem serve as column packing. The close coupled condenser and vacuum connection offer and extremely short condensate travel path. Used with 25mm immersion thermometer, and D27…
-
SYNTHWARE Dean Stark Distillation Receivers
Kemtech AmericaFor easy separation of water from reaction or distillation system.
-
Synthware Straight Drying Tubes
Kemtech AmericaSynthware straight drying tube. With top outer and lower inner standard taper joints of the same size.
-
Synthware Distillation Connecting Adapters
Kemtech AmericaSynthware distillation connecting adapter. With standard taper top outer joint and inner joints at bottom and the side arm. Bottom and side arm joints are angled at 75 degrees to one another.
-
Synthware Kjeldahl Distilling Trap Adapters
Kemtech AmericaAdapter is placed above flask to prevent carry-over of reactions which have a tendency to foam. With top outer and lower inner standard taper joints.