Glass Joints, Glass, Supplies
-
Adapter Connecting, NO-AIR
Ace GlassY shaped, 3-way adpater. One outer joint, two inner standard taper joints. Great for adapting flasks and other Schlenk line components. All three joints are the same size.
-
Adapters, Inert Gas, Inner Joint
ChemglassAdapter has two hose connections 180° from one another to permit a flow of inert gas over the apparatus. Hose connection has an O.D. of 10mm at the largest serration.
-
These PYREX® angle connecting adapters have a sidearm at an approximately 75° angle from the lower joint. The lower end and sidearm are equipped with inner 14/20 Standard Taper joints, and the upper end with an outer 14/20 Standard Taper joint. This tube is also a replacement part for…
-
SYNTHWARE Microscale Vigreux Distilling Heads
Kemtech AmericaWith Vigreux Indentations, used with 25mm immersion thermometer, and D27 distillation receiver.
-
-
Similar to the AF-0072 adapter, but with two #15 o-ring joints. Available in 0-4mm, 0-8mm or 0-12mm valve sizes. Each adapter is supplied complete with (2) #116 Viton o-rings.
-
Single stage oil diffusion pump useful with manifolds such as AF-0450 through AF-0454. Will provide vacuum of 10 -5 torr, at a pumping rate of approx 8L/sec. Instead of the typical internal heating coil, boiler has a round bottom for use with CG-10000-02 or CG-12000-02 100mL heating mantle. Use of…
-
Distilling Receiver, Complete
ChemglassCow type design has three receivers 45° apart. Condensers with lower drip tip inner joints will protrude into the spherical section, permitting the distillate to fall directly into the receiving flasks. Distribution adapter has a serrated connection for attachment to vacuum source. Complete…
-
Baffles, Glass or PTFE
Ace GlassUse Ace-Thred adapters to mate glass or PTFE (stainless steel core) baffles to any standard taper joint. See 5028 & 5030 series adapters. Baffles can be adjusted vertically or rotated to increase agitation.
-
Adapter, 15mm o-ring joint to standard taper or ball joints with o-ring seals. Fetfe o-rings for both joints are supplied.
-
Joints, O-Ring Seal
ChemglassJoint has an o-ring groove to accept the listed o-ring size. Provides for a grease-free, vacuum seal when used with CG-150 clamps. Each joint is supplied with a Viton o-ring of the listed size.
-
Solid, virgin PTFE, standard taper, joint inserts. For 6467 series stainless steel, flat heads. Top of insert is outside standard taper joint that matches glass standard taper inner joints. Bottom is made with a reverse thread and comes with a PTFE collar and FETFE o-ring for attaching to the flat…
-
Used in the filtration and recrystallization of highly sensitive materials. Filter tube has 14/20 standard taper inner joints at both ends along with a 14/20 outer joint for the connection to the 90º adapter. Isolation valve is supplied with a CG-961-01 0-4mm Chem-Vac™ Chem-Cap®…
-
-
Vessel only, enables cooling of reactant material during photolysis plus the added feature of a 2mm bore, 1:5 PTFE stopcock at bottom for draining contents of vessel. Made of borosilicate glass to accommodate the immersion well. With one 14/20 angled joint for sparger tube, one 24/40 vertical joint…
-
Lower Reservoirs, Gas Scrubbers
Chemglass3L 5-Neck heavy wall, round bottom flask lower reservoir for gas scrubber. Flask has a 60mm Duran Flange center neck, 2ea 45/50 outer joints, and 2ea 24/40 outer joints. Drain valve is a 0-14mm with Perfluoro o-rings. Valve is offset from the bottom of the flask to permit solids to settle and…
-
Adapter has a #15 o-ring joint with a 0-4mm 1-Arm Chem-Vac™ Chem-Cap® valve. Side arm is 9mm OD medium wall tubing for use with 3/8" Cajon® connections. Approx overall height is 100mm. Each adapter is supplied complete with one #116 Viton o-ring.
-
Cylindrical vessel with a 2mm bore PTFE stopcock at top, GPI threaded angled side port, & #15 Ace-Thred at bottom that accepts a PTFE adapter with removable Por. C glass filter disc & a PTFE shut-off valve. PTFE adapter has front type seal using a CAPFE O-Ring to make a compression seal in the #15…
-
Adapter, Flow Control Inlet
DWK Life Sciences (Kimble)Stopcock available with glass or PTFE plug For regulating the flow of gases or liquids into reaction systems. Adapter consists of male standard taper joint fittng with stopcock and a 90° angle male hose barb. Thomas numbers 5738D01, D03, D15, and D17 take 1/4" i.d. flex tubing; Thomas…
-
Spherical Joints, O-Ring Ball Members
ChemglassBall joint with a Viton o-ring fitted into a groove tooled at the midpoint of the grind. Provides for a flexible, vacuum tight seal when used with CG-121-P polished socket joints. Supplied complete with one Viton o-ring of the listed size.
-
Adapter, Connecting Hose
Ace GlassAdapter with bent hose connection top and either a standard taper or ball joint inner bottom. Codes -110,-112,-114 have an integral porosity A fritted disc.
-
PTFE Sleeves, .38mm
Ace GlassDesigned for use with inner member regular joints with only a slight mismatch. Treated on inner surface so that it may be cemented to glass with ACE 7560 epoxy adhesive. Sleeves may also be used uncemented to replace lubricant at low pressure differentials. ACE PTFE sleeves are accurately shaped to…
-
Synthware Distilling Adapters, 105°
Kemtech AmericaSynthware distillation adapter with sealed in drip tip. Adapter is bent at 105 degrees. Standard taper top outer joint and lower inner joints.
-
Synthware Vacuum Take-Off Adapters
Kemtech AmericaSynthware vacuum take-off adapter with drip tip. The upper outer and lower inner standard taper joints are the same size.
-
-
Synthware Distillation Adapters, Vigreux
Kemtech AmericaSynthware Vigreux distillation connecting adapter. Indenstations in lower section improve liquid/vapor contact. The standard taper top outer joint accomodates a 76mm immersion thermometer. Bottom and side joints are standard taper inner joints.
-
These Drying Tubes are replacement parts for the 6949M series of PYREX® microchemistry kits.
-
Adapter, Vacuum Filtration
Ace GlassUsed for reduced pressure filtration with 7186 style, plain stem Buchner funnels. Top is tooled to accept a pluro stopper, bottom has a joint. Serrated hose connection has a second ring of 13.5mm O.D. Inserting the recommended size pluro stopper and th
-
Adapters, Inlet, Airfree®, Schlenk
ChemglassGas inlet adapter with a 2mm glass stopcock having a constant pressure retention device. Available with a choice of inner or outer standard taper joint. Top arm is 9mm O.D. medium wall tubing for use with CG-3022 septum. Overall height of the 14/20 size is approx. 95mm while the 24/40 is approx. 120mm.
-
Adapter, Offset
Ace GlassAdapter with #15Ace-Thred top and 14mm OD offset bottom tube with O-Ring grove. Used on small pressure reaction vessels and heads to allow for more space for columns, condensers and addition funnels.
-
Adapter Univ Sz 21 24/40
DWK Life Sciences (Kimble)For use with plain thermometers, pipets, syringes or other small items with an OD from 2 to 17 mm. A vacuum-tight seal is created with the open top compression cap and FKM o-ring to allow adjustable immersion of thermometers Cap is suitable for use to 150 °C To use it as a septum…
-
SYNTHWARE Solvent Still, Built-In Condenser
Kemtech AmericaSolvent Still, Built-In Condenser Capacity: 125mL Joints: 24/40 Threaded Side Port: 14/10