Condensers, Supplies, Corning
-
These PYREX® condensers have a high surface area per unit length of the 300mm long jacket with a 24/40 Standard Taper outer joint at the top and a plain drip tip at the bottom. They are primarily used in distillation assemblies. Condenser tubulations are approximately 10mm O.D.
-
These PYREX® West condensers are designed with a 190mm long jacket that has a 14/20 Standard Taper top joint. The bottom has 14/20 Standard Taper inner joint with a drip tip. The tubulations are on the same side to reduce breakage. The tubulation O.D. is approximately 10mm. This condenser is a…
-
PYREX Graham Condensers
CorningGraham Coiled condensing tube is sealed into water jacket Inlet and outlet tubes on opposite sides of jacket With Standard Taper drip tip joint at bottom and Standard Taper outer joint at top The 8” condenser has 19/38 joints; others have Standard Taper 24/40 joints
-
PYREX West Condensers
CorningAvailable with 200 or 300 mm long heavy-wall outer jackets PYREX® West condensers are designed with a heavy-wall outer jacket to provide a sturdy, long-lasting unit, while the inner tube has a thinner wall for efficient heat transfer. The tubulations are on the same side to reduce breakage.…
-
This specially designed PYREX® cold finger condenser is a replacement part for the PYREX® Cyanide Distilling Apparatus (Thomas No. 0320A91)
-
PYREX® Liebig Condensers
CorningSuitable for the use in vacuum distillations With Standard Taper drip tip joint at bottom and Standard Taper outer joint at top The 8” condenser has Standard Taper 19/38 joints; others have 24/40 joints
-
This Jacketed Reflux Condenser is a replacement part for the 6949M series of PYREX® microchemistry kits.
-
This PYREX® Friedrichs type condenser affords very efficient operation. The helical inner tube fits closely within the jacket. The vapor tube is sealed to the jacket at an angle of 75° and has an outer 24/40 Standard Taper joint.
-
Condenser 200 mm
CorningThese PYREX® condensers have a high surface area per unit length of the 200mm long jacket with a 19/38 Standard Taper outer joint at the top and a plain drip tip at the bottom. They are primarily used in distillation assemblies Condenser tubulations are approximately 10mm O.D.
-
Column 190 mm 19/22
CorningThe PYREX® distilling condenser has 19/22 Standard Taper inner and outer joints, is simple in design and easy to use. Side tubulations are 10mm O.D. Distilling condensers are widely used in the lab, especially for fractionation. This condenser is also a replacement for organic chemistry kit No.…
-
This simple PYREX® cold finger condenser, of relatively low efficiency, is often used to regulate refluxing by adjusting the flow of air or water through it (dephlegmation). The tubulation O.D. is approximately 10mm. This condenser has a 24/40 inner Standard Taper joint and is a replacement…
-
PYREX Liebig Condensers
CorningWith Standard Taper 24/40 joints Inlet and outlet tubes, 10 mm o.d. are on opposite sides, indentations at lower end of condenser tube support packing when used as fractionating column.
-
This PYREX® general purpose condenser can be used for either distillation or extraction. Although the condensing area per unit length of the 200mm long jacket is low, the large capacity water jacket gives efficient cooling. Condenser tubulations are approximately 10mm O.D. The adapter end is…
-
This specially designed PTFE condenser jacket is a replacement part for the PTFE Cyanide Distilling Apparatus (Thomas No. 0320A91)
-
This Air Reflux Condenser is a replacement part for the 6949M series of PYREX® microchemistry kits.
-
These 250mL PYREX® atomizers are used for spraying reagents onto thin layer chromatography plates. They have a full length 24/40 Standard Taper joint between the reservoir and spraying device. The PYREX® distilling condenser has 14/20 Standard Taper inner and outer joints, is simple in design…
-
PYREX® Allihn Condensers
CorningAllihn - suitable for use in vacuum distillations With condensing tube expanded by series of bulbs which increase condensing area and lengthen condensate path Inlet and outlet tubes are on opposite sides of the jacket All sizes take stopper size 3 and have Standard Taper drip…
-
PYREX Liebig Condensers
CorningSuitable for refluxing, extracting and distilling operations With Standard Taper 24/40 drip tip joint at bottom All sizes take stopper size 3