Ace Glass, Chemicals, Stirrers
-
Stir Shaft, Retreat Agitator, PTFE
Ace GlassPTFE covered stainless steel shaft with a solid PTFE retreat curve agitator. Featuring a retreat angle of 30 degrees and, for a better grip by the stir motor chuck,50mm of exposed stainless.
-
Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8076 (19mm od) or 8080 (28mm od) polished glass stir shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…
-
Bearing, Trubore, Water Cooled, 19mm
Ace GlassTrubore bearing, jacketed, spherical joint. Designed to accomodate our 8112-10 packing box. For use with 8077 & 8078 19mm od precision ground glass shafts or 8079 PTFE covered shafts. Spherical joint can be clamped to prevent rotation. Trubore length of 15.2cm or 6 inches.
-
Stirrer Blades, PTFE, Oval, 10mm Shafts
Ace GlassPTFE oval stir blades for 10mm OD button type stir shafts. 10mm OD shafts can be found in our 8068, 8070, 8074 and 8075 series.
-
Air Motor, Heavy Duty
Ace GlassA compact, heavy duty air motor with highly damped muffler. Complete unit consists of an air hose with a snap coupling on motor end and shut-off valve on the other. Motor will develop 1.5 hp. at 90 lbs. air pressure. Speeds are variable from 300 to 3000 r.p.m. It consumes approximately 1.98m3 free…
-
316 stainless steel, football shaped, stir blades for 10mm OD button type stir shafts. Holed versions, codes -70 thru -74, provide even greater agitation. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.
-
PTFE, large-scale, multi-paddle agitator design to accept pinned bottom valves, like our 6482 flush-seal valve. The pin helps reduce wobble or flexing at higher rpm. 19mm agitators will fit drilled type or knob type 8076, 8078 and 8079 shafts.
-
Motor Controller, Solid State
Ace GlassRated 1 hp. for use with most stirrer motors. Not for use with shunt wound DC motors. A compact, lightweight, solid state, ring stand mountable control unit, both AC and DC outlets. Pulsed AC gives better low speed torque than voltage dropping devices such as rheostat or transformer. AC output: 120…
-
Agitator, PTFE, 4 Blade
Ace Glass4 Blade PTFE agitator available with either 45 or 90 degree blade angle. For use with glass or metal shafts and is secured using a compression style fitting allowing it to positioned anywhere along the length of the shaft.
-
Bearing, Trubore, Gas Balancing, 10mm
Ace GlassThis bearing is supplied with tubulation for feeding inert gases around the bearing to balance any pressure possibly being developed in the flask. Can also be used for gas-liquid reactions and gas dispersions using our hollow precision ground stirring shafts (8068, 9532).
-
PTFE covered stainless steel stirring shafts, 10mm OD, drilled type. If used unlubricated, 500 rpm max with water cooled 8040 bearing, 100 rpm max recommended with 8036, 8038, 8039, 8043, 8047, 8051 and 8055 bearings. With condensate film as added heat transfer agent, 2000 rpm can be attained.…
-
Stirring Shaft Coupling
Ace GlassStir shaft couplings for connecting glass or metal stir shafts to the adjustable chuck on an overhead stir motor. Compression connection is secured to various OD shafts via an Allen screw coupling. The Codes -22 and -24 are complete pass-thru assemblies that enable height adjustment on stir shafts…
-
Chuck, Flex-Grip®
Ace GlassNylon chuck for use with ACE stirring shafts or other shafts of the same dimensions. Chuck has flexible insert which allows for misalignment of shaft without danger of breakage.
-
Stirrer, Complete
Ace GlassPrecision Trubore Stirrer Assembly consisting of 10 mm ID bearing, bushing, precision ground, button type glass shaft and blade. Available with either glass or PTFE stir blade.
-
Bearing, Trubore, Plain, 10mm
Ace GlassInterchangeable bearing designed to be used with our precision ground stirring shafts (8068,8070,8071,8073,9532,9533). Recommended top stirring speed with our 8117 Stir-Lube is 1500 rpm.
-
Precision ground glass stirring shaft, 10mm OD, attached vanes. Vanes will fit through a 45/50 joint and are contoured for use with our 9448 and 9456 series Mini-Lab flasks. Use with Trubore bearings 8036, 8038, 8039, 8040, 8042, 8043, 8047, 8051, 8053 and 8055. Compatible with our 8050 mechanical…
-
Precision ground glass stirring shafts,10mm OD, crescent type. Useful for stirring viscous materials at low rpm. Available for round bottom flasks of 1, 3 and 5 liters. Code -19, 3 liter size will fit a 2 liter flask, but closely. Flask opening must be 29/42 or larger. Use with Trubore bearings…
-
Bearing, Trubore, 10mm
Ace GlassFor use with Flask Head 9443. By using precision bore tubing throughout the length of the bearing, a stirrer is produced that will hold to within 1mm of vacuum and withstand pressures in the flask up to 300mm. The 9532 Agitator, used with this bearing actually develops a negative pressure of 230mm…
-
Precision ground glass stirring shaft with attached vanes, 10mm. For use when agitation and gas introduction are desired at the same time. Agitator will fit through a 45/50 joint. Designed for use with our 9523 Trubore bearing and 9443 or 9446 mini-lab flask heads. Introduced gas exits the hollow…
-
Precision PTFE covered stainless steel stirring shafts, 19mm OD. Drilled type shafts accept 8091,8092,8093,8100 agitators and can be used in 19mm Trubore bearings (8059, 8060, 8061 & 8065). Not recommended for PTFE bearings 8050, 8067 and 13445. Join to stirrer motor using 8124 series chucks.
-
Agitator, PTFE, Large Scale Multi-blade
Ace GlassThese heavy-duty PTFE agitators impart maximum energy and are offset at the bottom to accomodate slurries. 10mm agitators fit drilled type or knob type 8068, 8071 & 8075 shafts. 19mm agitators fit drilled type or knob type 8076, 8078 & 8079 shafts. 28mm agitators fit 8080 drilled shafts.
-
Bearing, Trubore, Ace-Thred, 10mm
Ace GlassSelf-aligning, three-piece bearing. Complete consists of inner Trubore bearing, Nylon bushing with O-Ring, and threaded adapter. Unique design eliminates costly replacement since inner bearing will spin if shaft binds or will self-align at O-Ring seal in the event the motor is slightly cocked.…
-
Stirring Shaft, Glass, Polished, 10mm
Ace GlassPolished glass stirring shafts, 10mm OD. Recommended for use with only our 8050,8066,13443 and 13445 bearings. Join 8083,8085,8086,8087,8096 blades to button type shafts. Join 8088, 8089, 8090 & 8091 agitators to bead type shafts. Plain shafts will accept 8094 & 8095 agitators secured with a…
-
Fully flexible drive shaft facilitates isolation of the stirrer motor from the reactor. Complete units, code -30 (91.4cm) and code -32 (152.4cm), designed for use with 8mm (5/16in) motor shaft. Purchase the optional code -27 adapter for motors with 9.5mm (3/8in) shafts. Reactor end consists of a…
-
Agitator, PTFE, Turbine, For 10mm Shaft
Ace GlassAll-PTFE turbine type agitator. Unique locking arrangement assures positive grip. Agitator fits 10 mm shafts. Shaft opening is drilled straight thru to allow positioning of agitator at any drilled position on shaft as well as the bottom. For use with bead type glass shafts, 8068-G, 8075 or PTFE…
-
Stirrer, Laboratory, Solid State
Ace GlassTotally enclosed, 1/40hp DC permanent magnet motor with dual 8 mm (5/16") armature and gear shafts with milled flats. Armature shaft with maximum speed of 4000rpm.; 18:1 ratio gear shaft rated 3.6in-lb torque, up to 333rpm. Motor supplied with 1.5 meter 3-wire cable for controller connection.…
-
Stirring bars with large, 25mm (1 inch) raisied center ring.
-
Ultra-Vacuum stirrer bearing for applications up to 0.6 Torr. Non-shedding bearing is manufactured from PTFE, Rulon and PEEK materials. Equally good in both vacuum and pressure applications as low as 0.6 Torr. Rated for up to 400 rpm with both glass (polished rather than precision ground is best)…
-
Bearing, Trubore, 5 & 6mm
Ace GlassTrubore bearing with standard taper joint for use with our 9534, 9535 and 9541 precision ground stir shafts. Lubricant well at top will accept enough 8117 Stir-Lube to provide hours of operation at up to 1000 rpm. Match bearing ID with stir shaft OD.
-
Stirrer Bearing, PTFE, 6-10MM Shafts
Ace GlassPTFE stirrer bearing featuring a non-shedding, fully enclosed, anti-whip, chemically resistant design. Models available for 6, 8 and 10mm glass, metal or PTFE stir shafts. Can be used in slight pressure or vacuum applications. Maximum recommended speed for continuous operation is 500 rpm. Unlike…
-
3/8HP Brushless DC motor for use on pilot plant reactors up ²to 200L. May be used with either the 120V or 240V BLDC ²motor controllers. Supplied with 6ft removable cable and ²mounting hardware.
-
Pass-Thru Rod, Flexible shaft
Ace GlassPass-thru rod for use with Caframo 13565 & 13566 stir motors attached to our 8081 flexible stirring shaft.