Ace Glass
-
Air Sampling Sweep Elbow
Ace GlassSweep elbow, available with one end threaded, the other end reduced for use with 7506 bushing or both ends threaded for use with either 7506 bushing or 5841 coupling.
-
-
Distilling round-bottom flask coated with Ace Instatherm. Designed to operate up to 360 & deg; C, heating response time is very rapid, (5° per minute), with very low thermal lag. Has vertical standard taper reinforced outer center neck and angled standard taper reinforced outer side neck.…
-
Adapter, Sublimation
Ace GlassUnique device for carrying out sublimation directly in round bottom reaction flask; simply remove condenser, stirrer, etc. from joint, insert sublimation adapter and begin. Coolant connection at top and side vacuum connection are 9.5 mm (3/8") O.D. Vacuum connection is controlled by 1:5 PTFE 2 mm…
-
Stopcock adapter, inner joint bottom, #7 top, stopcock side arm with PTFE plug and hose connection end. Supplied bushing and FETFE o-ring allows compression seal with thermometers, bleed tubes, etc. Will accomodate thermometers or tubes up to 7mm OD. F
-
Micro Soxhlet, Improved Design
Ace GlassDesigned for small chemical applications. Improved design permits greater condensing capacity. Condenser approximately 139mm jacket length. Joint between condenser and extractor is 24/25. Flask joint is 14/20. Designed to accommodate paper thimble, size 10 x 50 mm. Flask is 30mL capacity. Hose…
-
Precision ground glass stirring shaft with attached vanes, 10mm. For use when agitation and gas introduction are desired at the same time. Agitator will fit through a 45/50 joint. Designed for use with our 9523 Trubore bearing and 9443 or 9446 mini-lab flask heads. Introduced gas exits the hollow…
-
-
Agitator, PTFE, Large scale, Turbine
Ace GlassA turbine type agitator, available for 19mm and 28mm shafts. 19mm six blade agitators are open in the center to allow custom positioning on drilled type or knob type 8076, 8078 & 8079 shafts. 28mm four blade agitators are supplied with a PTFE nut & bolt set for securing to 8080 shafts. Shaft is not included.
-
Beaker, Kilo Scale with pourout
Ace GlassLarge size graduated beaker for batch operations and mixing large volumes of measured liquids.
-
Reaction Assembly, Portable, 12 and 22L
Ace GlassComplete self-supporting pilot plant assembly. Needs only to be located near coolant and electrical outlet. When not in use, entire assembly can be intact, without breakdown. Features flask, self-standing mechanical or air motor, flat-sided powder funn
-
Pressure Vessels, Tubes & Bottles
Ace GlassAce Glass pressure tubes and bottles are the premier glass pressure vessels in the industry. Flat-bottomed bottles are rated at 60psi at room temperature while our tubes are rated at 150psi at as much as 120 degrees C. Due to varying conditions, Ace cannot guarantee glass vessels from breaking…
-
Condenser, Air Reflux
Ace GlassMicroscale air condenser normally used in reflux experiments. When packed with desiccant material, condenser becomes a drying tube. With inner joint at bottom, outer joint at top. Codes -10, -14 and -17 supplied with drip tip for use with 9595 Spinning Band Column. Effective length, approximately…
-
Distilling Head
Ace GlassAutomatic, reflux control via solenoid valve arrangement. Reflux control is effected by an adjustable time switch and solenoid takeoff valve. Reflux ratio is a time function and independent of throughput except when a single drop is a significant part of the condensate. Viscous liquids cause no…
-
Offset gearbox and motors complete with right angle drive unit for pilot plant systems. Motors with right-angle drive save headspace and work well where height is restricted. Available for standard or hazardous duty applications. Available in either 1/4hp or 1/2hp with a digital 115/230v 50/60Hz…
-
Heavy wall cylindrical reaction flask with Duran grooved flange opening. Flask has Zero Dead Space, (ZDS), bottom valve. The valve features no material hang-up in the fully open position. When closed, the valve seats flush with the bottom of the flask. Includes one CAPFE o-ring. See Ace 6517 for…
-
Standard Clamp
Ace GlassClamp is designed to fit 4 inch conical flanges, allowing the top half to be removed without disturing the lower half. Clamp features and extension arm (1/2 x 8 inch) suitable for attachment to an appropriate support stand or lab frame. Silicone liner will withstand temperatures up to 500ºdegF.
-
Cell Window Holder
Ace GlassNylon cell window holder for use with 7894 Photochemical Cells and 7895 Cell Windows. The removable cell window is compressed between two FETFE O-Rings for a leak-tight fit. Holder is then threaded into end of a 7894 Cell until O-Ring compression seal is formed between the holder and the cell.…
-
Temperature Controller
Ace GlassTemperature controller ideal for two circuit mantles or general use. Features two front mounted outlets, 16 segment ramp and soak function, fuzzy logic auto tune PID, type 'J' thermocouple, dual 4 digit LED display, universal TC jack for "mini" or "standard" plugs. Unit is downsized, compact and…
-
Filter Material, Discs and Fabric
Ace GlassFilter material and discs (paper, PTFE, and polypropylene).
-
Temperature Sensors, Pt100 type
Ace GlassPt100 (100ohm platinum wire resistance temperature detector) probes provide measurement over a temperature range of -20 degrees C to 550 degrees C. Less economical than J or K type probes, however they are not susceptible to drift, aging or corrosion. Supplied with male phone plug ends. Code -23…
-
-
Condenser, Spiral
Ace GlassWith spiral condensing tube having both inlet and outlet connections at top, on same side. With standard taper joints. Length between joints is approximately 80-90 mm longer than the stated coil length.
-
Adapter, Thermometer, 10/20
Ace GlassMade of PTFE with Nylon knurled nut to adapt standard chemical thermometers. For use in 10/18 or 10/30 joints. Simple to use: insert thermometer to desired depth, tighten nut.
-
TUBE, Receiving, Graduated
Ace Glass100ml graduated, rotary evaporator receiving tube. Tapered bottom with 35/20 spherical outer joint top. Graduated in 0.5ml increments to 10ml, 5ml increments to 100ml.
-
Thomas Nos. 1165M15, 1165M16, 1165M17, 1165M18, 1165M19, 1165M20, 1165M21 Jacketed cylindrical flask with flush seal and beaded pipe²inlet and outlets. The flask is graduated on both sides²which allows for either left or right hand orientation.²Features a Schott-Duran style o-ring…
-
Truebore, Precision Glass Tubing
Ace GlassInside diameter tolerance of 0.0004", Trubore, a trademark of Ace Glass Incorporated, stands for precision bore tubing of the highest quality, maintained by production techniques, careful selection of raw materials, and step-by-step quality control. Trubore tubing is used in ACE items such as our…
-
Zero holdup, no-splash short path still for small quantity distillations with the accuracy of larger setups. Improved design eliminates even the minimal holdup experienced with original short path stills by further reducing wetted surfaces and travel p
-
Stirrer, Laboratory, Solid State
Ace GlassTotally enclosed, 1/40hp DC permanent magnet motor with dual 8 mm (5/16") armature and gear shafts with milled flats. Armature shaft with maximum speed of 4000rpm.; 18:1 ratio gear shaft rated 3.6in-lb torque, up to 333rpm. Motor supplied with 1.5 meter 3-wire cable for controller connection.…
-
Instatherm Desicator, Vacuum Oven
Ace Glass250mm dia with bottom Instatherm® heated,(low voltage: 40 volts, 10 amps max.) Top is not heated, but has insulation cover. May be used as a vacuum oven at temps up to 180 degrees C continuously. The top has an observation stripe for visibility & is supplied with vacuum take-off valve. Uncoated…
-
Distilling Receiver, Vacuum Type
Ace GlassWith standard taper joint at top. Capacity 100mL, in 1mL subdivisions.
-
Distilling Receiver, with Side Arm
Ace GlassGraduated to 15mL in 1/10mL subdivisions with lower 0.5mL contained in a precision tip for better accuracy with extremely small samples.